README revision 1.8
1Configuring FAITH IPv6-to-IPv4 TCP relay 2 3Kazu Yamamoto and Jun-ichiro itojun Hagino 4$NetBSD: README,v 1.8 2000/07/04 20:08:32 thorpej Exp $ 5$KAME: README,v 1.5 2000/07/02 08:50:50 itojun Exp $ 6 7 8Introduction 9============ 10 11FAITH is a IPv6-to-IPv4 TCP relay. It performs tcp relay just as some of 12firewall-oriented gateway does, but between IPv6 and IPv4 with address 13translation. 14TCP connections has to be made from IPv6 node to IPv4 node. FAITH will 15not relay connections for the opposite direction. 16To perform relays, FAITH daemon needs to be executed on a router between 17your local IPv6 site and outside IPv4 network. The daemon needs to be 18invoked per each TCP services (TCP port number). 19 20 IPv4 node "dest" = 123.4.5.6 21 | 22 [[[[ outside IPv4 ocean ]]]] 23 | 24 node that runs FAITH-daemon (usually a router) 25 | 26 ==+=====+===+==== IPv6, or IPv4/v6 network in your site ^ 27 | | | connection 28 clients IPv6 node "src" | 29 30You will have to allocate an IPv6 address prefix to map IPv4 addresses into. 31The following description uses 3ffe:0501:1234:ffff:: as example. 32Please use a prefix which belongs to your site. 33FAITH will make it possible to make a IPv6 TCP connection From IPv6 node 34"src", toward IPv4 node "dest", by specifying FAITH-mapped address 353ffe:0501:1234:ffff::123.4.5.6 36(which is, 3ffe:0501:1234:ffff:0000:0000:7b04:0506). 37The address mapping can be performed by hand:-), by speical nameserver on 38the network, or by special resolver on the source node. 39 40 41Setup 42===== 43 44The following example assumes: 45- You have assigned 3ffe:0501:1234:ffff:: as FAITH adderss prefix. 46- You are willing to provide IPv6-to IPv4 TCP relay for telnet. 47 48<<On the translating router on which faithd runs>> 49 50(1) If you have IPv6 TCP server for the "telnet" service, i.e. telnetd via 51 inet6d, disable that daemon. Comment out the line from "inet6d.conf" 52 and send the HUP signal to "inet6d". 53 54(2) Execute sysctl as root to enable FAITH support in the kernel. 55 56 # sysctl -w net.inet6.ip6.keepfaith=1 57 58(3) Route packets toward FAITH prefix into "faith0" interface. 59 60 # ifconfig faith0 create up 61 # route add -inet6 3ffe:0501:1234:ffff:: -prefixlen 64 \ 62 fe80::xxxx:yyyy:zzzz:wwww%faith0 63 64(4) Execute "faithd" by root as follows: 65 66 # faithd telnet /usr/libexec/telnetd telnetd 67 68 1st argument is a service name you are willing to provide TCP relay. 69 (it can be specified either by number "23" or by string "telnet") 70 2nd argument is a path name for local IPv6 TCP server. If there is a 71 connection toward the router itself, this program will be invoked. 72 3rd and the following arguments are arguments for the local IPv6 TCP 73 server. (3rd argument is typically the program name without its path.) 74 75 More examples: 76 77 # faithd login /usr/libexec/rlogin rlogind 78 # faithd shell /usr/libexec/rshd rshd 79 # faithd ftpd /usr/libexec/ftpd ftpd -l 80 # faithd sshd 81 82 83<<Routing>> 84 85(4) Make sure that packets whose destinations match the prefix can 86reach from the IPv6 host to the translating router. 87 88<<On the IPv6 host>> 89 90There are two ways to translate IPv4 address to IPv6 address: 91 (a) Faked by DNS 92 (b) Faked by /etc/hosts. 93 94(5.a) Install "newbie" and set up FAITH mode. See kit/ports/newbie. 95 96(5.b) Add an entry into /etc/hosts so that you can resolve hostname into 97faked IPv6 addrss. For example, add the following line for www.netbsd.org: 98 99 3ffe:0501:1234:ffff::140.160.140.252 www.netbsd.org 100 101<<On the translating router on which faithd runs.>> 102 103(6) To see if "faithd" works, watch "/var/log/daemon". Note: please 104setup "/etc/syslog.conf" so that LOG_DAEMON messages are to be stored 105in "/var/log/daemon". 106 107 <e.g.> 108 daemon.* /var/log/daemon 109 110 111Advanced configuration 112====================== 113 114If you would like to restrict IPv4 destination for translation, you may 115want to do the following: 116 117 # route add -inet6 3ffe:0501:1234:ffff::123.0.0.0 -prefixlen 104 \ 118 -interface faith0 119 120By this way, you can restrict IPv4 destination to 123.0.0.0/8. 121You may also want to reject packets toward 3ffe:0501:1234:ffff::/64 which 122is not in 3ffe:0501:1234:ffff::123.0.0.0/104. This will be left as excerside 123for the reader. 124 125By doing this, you will be able to provide your IPv4 web server to outside 126IPv6 customers, without risks of unwanted open relays. 127 128 [[[[ IPv6 network outside ]]]] | 129 | | connection 130 node that runs FAITH-daemon (usually a router) v 131 | 132 ========+======== IPv4/v6 network in your site 133 | (123.0.0.0/8) 134 IPv4 web server 135