Copyright (c) 1985, 1991, 1993
The Regents of the University of California. All rights reserved.
Redistribution and use in source and binary forms, with or without
modification, are permitted provided that the following conditions
are met:
1. Redistributions of source code must retain the above copyright
notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright
notice, this list of conditions and the following disclaimer in the
documentation and/or other materials provided with the distribution.
3. Neither the name of the University nor the names of its contributors
may be used to endorse or promote products derived from this software
without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE REGENTS AND CONTRIBUTORS ``AS IS'' AND
ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
ARE DISCLAIMED. IN NO EVENT SHALL THE REGENTS OR CONTRIBUTORS BE LIABLE
FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
SUCH DAMAGE.
@(#)ping.8 8.2 (Berkeley) 12/11/93
.Dd September 10, 2011 .Dt PING 8 .Os .Sh NAME .Nm ping .Nd send .Tn ICMP ECHO_REQUEST packets to network hosts .Sh SYNOPSIS .Nm .Op Fl aCDdfLnoPQqRrv .Op Fl c Ar count .Op Fl E Ar policy .Op Fl g Ar gateway .Op Fl h Ar host .Op Fl I Ar srcaddr .Op Fl i Ar interval .Op Fl l Ar preload .Op Fl p Ar pattern .Op Fl s Ar packetsize .Op Fl T Ar ttl .Op Fl t Ar tos .Op Fl w Ar deadline .Ar host .Sh DESCRIPTION .Nm uses the .Tn ICMP protocol's mandatory .Tn ECHO_REQUEST datagram to elicit an .Tn ICMP ECHO_RESPONSE from a host or gateway. .Tn ECHO_REQUEST datagrams (``pings'') have an IP and .Tn ICMP header, followed by a .Dq struct timespec and then an arbitrary number of ``pad'' bytes used to fill out the packet. The options are as follows: l -tag -width Ds t Fl a Emit an audible beep (by sending an ascii BEL character to the standard error output) after each non-duplicate response is received. This is disabled for flood pings as it would probably cause temporary insanity. t Fl C Send timestamps in compat format; two 32 bit words in little endian format, the first one representing seconds, and the second one representing microseconds. t Fl c Ar count Stop after sending (and waiting the specified delay to receive) .Ar count .Tn ECHO_RESPONSE packets. t Fl D Set the .Dv Don't Fragment bit in the IP header. This can be used to determine the path MTU. t Fl d Set the .Dv SO_DEBUG option on the socket being used. t Fl E Ar policy Use IPsec policy specification string .Ar policy for packets. For the format of specification string, please refer .Xr ipsec_set_policy 3 . Please note that this option is same as .Fl P in KAME/FreeBSD and KAME/BSDI (as .Fl P was already occupied in .Nx ) . t Fl f Flood ping. Outputs packets as fast as they come back or one hundred times per second, whichever is more. For every .Tn ECHO_REQUEST sent a period ``.'' is printed, while for every .Tn ECHO_REPLY received a backspace is printed. This provides a rapid display of how many packets are being dropped. Only the super-user may use this option. f -emphasis This can be very hard on a network and should be used with caution. .Ef t Fl g Ar gateway Use Loose Source Routing to send the ECHO_REQUEST packets via .Ar gateway . t Fl h Ar host is an alternate way of specifying the target host instead of as the last argument. t Fl I Ar srcaddr Set the source IP address to .Ar srcaddr which can be a hostname or an IP number. For multicast datagrams, it also specifies the outgoing interface. t Fl i Ar interval Wait .Ar interval seconds .Em between sending each packet . The default is to wait for one second between each packet, except when the -f option is used the wait interval is 0.01 seconds. t Fl L Disable loopback when sending to multicast destinations, so the transmitting host doesn't see the ICMP requests. t Fl l Ar preload If .Ar preload is specified, .Nm sends that many packets as fast as possible before falling into its normal mode of behavior. Only the super-user may use this option. t Fl n Numeric output only. No attempt will be made to look up symbolic names for host addresses. t Fl o Exit successfully after receiving one reply packet. t Fl P Use a pseudo-random sequence for the data instead of the default, fixed sequence of incrementing 8-bit integers. This is useful to foil compression on PPP and other links. t Fl p Ar pattern You may specify up to 16 ``pad'' bytes to fill out the packet you send. This is useful for diagnosing data-dependent problems in a network. For example, .Dq Li -p ff will cause the sent packet to be filled with all ones. t Fl Q Do not display responses such as Network Unreachable ICMP messages concerning the ECHO_REQUESTs sent. t Fl q Quiet output. Nothing is displayed except the summary lines at startup time and when finished. t Fl R Record Route. Includes the .Tn RECORD_ROUTE option in the .Tn ECHO_REQUEST packet and displays the route buffer on returned packets. This should show the path to the target host and back, which is especially useful in the case of asymmetric routing. Note that the IP header is only large enough for nine such addresses, and only seven when using the .Fl g option. This is why it was necessary to invent .Xr traceroute 8 . Many hosts ignore or discard this option. t Fl r Bypass the normal routing tables and send directly to a host on an attached network. If the host is not on a directly-attached network, an error is returned. This option can be used to ping a local host through an interface that has no route through it (e.g., after the interface was dropped by .Xr routed 8 ) . t Fl s Ar packetsize Specifies the number of data bytes to be sent. The default is 56, which translates into 64 .Tn ICMP data bytes when combined with the 8 bytes of .Tn ICMP header data. The maximum allowed value is 65467 bytes. t Fl T Ar ttl Use the specified time-to-live. t Fl t Ar tos Use the specified hexadecimal type of service. t Fl v Verbose output. .Tn ICMP packets other than .Tn ECHO_RESPONSE that are received are listed. t Fl w Ar deadline Specifies a timeout, in seconds, before ping exits regardless of how many packets have been sent or received. .El
p When using .Nm for fault isolation, it should first be run on the local host, to verify that the local network interface is up and running. Then, hosts and gateways further and further away should be ``pinged''.
p Round-trip times and packet loss statistics are computed. If duplicate packets are received, they are not included in the packet loss calculation, although the round trip time of these packets is used in calculating the minimum/average/maximum round-trip time numbers.
p When the specified number of packets have been sent (and received) or if the program is terminated with a .Dv SIGINT , a brief summary is displayed. The summary information can be displayed while .Nm is running by sending it a .Dv SIGINFO signal (see the .Dq status argument for .Xr stty 1 for more information).
p .Nm continually sends one datagram per second, and prints one line of output for every ECHO_RESPONSE returned. On a trusted system with IP Security Options enabled, if the network idiom is not MONO, .Nm also prints a second line containing the hexadecimal representation of the IP security option in the ECHO_RESPONSE. If the .Fl c count option is given, only that number of requests is sent. No output is produced if there is no response. Round-trip times and packet loss statistics are computed. If duplicate packets are received, they are not included in the packet loss calculation, although the round trip time of these packets is used in calculating the minimum/average/maximum round-trip time numbers. When the specified number of packets have been sent (and received) or if the program is terminated with an interrupt (SIGINT), a brief summary is displayed. When not using the .Fl f (flood) option, the first interrupt, usually generated by control-C or DEL, causes .Nm to wait for its outstanding requests to return. It will wait no longer than the longest round trip time encountered by previous, successful pings. The second interrupt stops ping immediately.
p This program is intended for use in network testing, measurement and management. Because of the load it can impose on the network, it is unwise to use .Nm during normal operations or from automated scripts. .Sh ICMP PACKET DETAILS An IP header without options is 20 bytes. An .Tn ICMP .Tn ECHO_REQUEST packet contains an additional 8 bytes worth of .Tn ICMP header followed by an arbitrary amount of data. When a .Ar packetsize is given, this indicated the size of this extra piece of data (the default is 56). Thus the amount of data received inside of an IP packet of type .Tn ICMP .Tn ECHO_REPLY will always be 8 bytes more than the requested data space (the .Tn ICMP header).
p If the data space is at least .Dv sizeof(struct timespec) (16) large, .Nm uses the first .Dv sizeof(struct timespec) bytes to include a timestamp to compute round trip times. Otherwise if the data space is at least eight bytes large (or the .Fl C flag is specified), .Nm uses the first eight bytes of this space to include a timestamp to compute round trip times. If there are not enough bytes of pad no round trip times are given. .Sh DUPLICATE AND DAMAGED PACKETS .Nm will report duplicate and damaged packets. Duplicate packets should never occur, and seem to be caused by inappropriate link-level retransmissions. Duplicates may occur in many situations and are rarely (if ever) a good sign, although the presence of low levels of duplicates may not always be cause for alarm.
p Damaged packets are obviously serious cause for alarm and often indicate broken hardware somewhere in the .Nm packet's path (in the network or in the hosts). .Sh TRYING DIFFERENT DATA PATTERNS The (inter)network layer should never treat packets differently depending on the data contained in the data portion. Unfortunately, data-dependent problems have been known to sneak into networks and remain undetected for long periods of time. In many cases the particular pattern that will have problems is something that doesn't have sufficient ``transitions'', such as all ones or all zeros, or a pattern right at the edge, such as almost all zeros. It isn't necessarily enough to specify a data pattern of all zeros (for example) on the command line because the pattern that is of interest is at the data link level, and the relationship between what you type and what the controllers transmit can be complicated.
p This means that if you have a data-dependent problem you will probably have to do a lot of testing to find it. If you are lucky, you may manage to find a file that either can't be sent across your network or that takes much longer to transfer than other similar length files. You can then examine this file for repeated patterns that you can test using the .Fl p option of .Nm . .Sh TTL DETAILS The .Tn TTL value of an IP packet represents the maximum number of IP routers that the packet can go through before being thrown away. In current practice you can expect each router in the Internet to decrement the .Tn TTL field by exactly one.
p The .Tn TCP/IP specification states that the .Tn TTL field for .Tn TCP packets should be set to 60, but many systems use smaller values
o x 4.3 uses 30, x 4.2 used 15
c .
p The maximum possible value of this field is 255, and most x systems set the .Tn TTL field of .Tn ICMP ECHO_REQUEST packets to 255. This is why you will find you can ``ping'' some hosts, but not reach them with .Xr telnet 1 or .Xr ftp 1 .
p In normal operation ping prints the ttl value from the packet it receives. When a remote system receives a ping packet, it can do one of three things with the .Tn TTL field in its response: l -bullet t Not change it; this is what Berkeley x systems did before the x 4.3 tahoe release. In this case the .Tn TTL value in the received packet will be 255 minus the number of routers in the round-trip path. t Set it to 255; this is what current Berkeley x systems do. In this case the .Tn TTL value in the received packet will be 255 minus the number of routers in the path .Em from the remote system .Em to the .Nm Ns Em ing host. t Set it to some other value. Some machines use the same value for .Tn ICMP packets that they use for .Tn TCP packets, for example either 30 or 60. Others may use completely wild values. .El .Sh EXIT STATUS .Nm returns 0 on success (the host is alive), and non-zero if the arguments are incorrect or the host is not responding. .Sh SEE ALSO .Xr netstat 1 , .Xr icmp 4 , .Xr inet 4 , .Xr ip 4 , .Xr ifconfig 8 , .Xr routed 8 , .Xr spray 8 , .Xr traceroute 8 .Sh HISTORY The .Nm command appeared in x 4.3 . IPsec support was added by WIDE/KAME project. .Sh BUGS Flood pinging is not recommended in general, and flood pinging a broadcast or multicast address should only be done under very controlled conditions.
p The .Nm program has evolved differently under different operating systems, and in some cases the same flag performs a different function under different operating systems. The .Fl t flag conflicts with .Fx . The .Fl a , c , I , i , .Fl l , P , p , s , and .Fl t flags conflict with .Sy Solaris .
p Some hosts and gateways ignore the .Tn RECORD_ROUTE option.
p The maximum IP header length is too small for options like .Tn RECORD_ROUTE to be completely useful. There's not much that that can be done about this, however.
Indexes created Sat Sep 20 22:09:52 GMT 2025