ingenic_regs.h revision 1.13
1 /* $NetBSD: ingenic_regs.h,v 1.13 2015/04/21 19:19:31 macallan Exp $ */ 2 3 /*- 4 * Copyright (c) 2014 Michael Lorenz 5 * All rights reserved. 6 * 7 * Redistribution and use in source and binary forms, with or without 8 * modification, are permitted provided that the following conditions 9 * are met: 10 * 1. Redistributions of source code must retain the above copyright 11 * notice, this list of conditions and the following disclaimer. 12 * 2. Redistributions in binary form must reproduce the above copyright 13 * notice, this list of conditions and the following disclaimer in the 14 * documentation and/or other materials provided with the distribution. 15 * 16 * THIS SOFTWARE IS PROVIDED BY THE NETBSD FOUNDATION, INC. AND CONTRIBUTORS 17 * ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED 18 * TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR 19 * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE FOUNDATION OR CONTRIBUTORS 20 * BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR 21 * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF 22 * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS 23 * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN 24 * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) 25 * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE 26 * POSSIBILITY OF SUCH DAMAGE. 27 */ 28 29 #ifndef INGENIC_REGS_H 30 #define INGENIC_REGS_H 31 32 /* for wbflush() */ 33 #include <mips/locore.h> 34 35 /* UARTs, mostly 16550 compatible with 32bit spaced registers */ 36 #define JZ_UART0 0x10030000 37 #define JZ_UART1 0x10031000 38 #define JZ_UART2 0x10032000 39 #define JZ_UART3 0x10033000 40 #define JZ_UART4 0x10034000 41 42 /* LCD controller base addresses, registers are in jzfb_regs.h */ 43 #define JZ_LCDC0_BASE 0x13050000 44 #define JZ_LCDC1_BASE 0x130a0000 45 46 /* watchdog */ 47 #define JZ_WDOG_TDR 0x10002000 /* compare */ 48 #define JZ_WDOG_TCER 0x10002004 49 #define TCER_ENABLE 0x01 /* enable counter */ 50 #define JZ_WDOG_TCNT 0x10002008 /* 16bit up count */ 51 #define JZ_WDOG_TCSR 0x1000200c 52 #define TCSR_PCK_EN 0x01 /* PCLK */ 53 #define TCSR_RTC_EN 0x02 /* RTCCLK - 32.768kHz */ 54 #define TCSR_EXT_EN 0x04 /* EXTCLK - 48MHz */ 55 #define TCSR_PRESCALE_M 0x38 56 #define TCSR_DIV_1 0x00 57 #define TCSR_DIV_4 0x08 58 #define TCSR_DIV_16 0x10 59 #define TCSR_DIV_64 0x18 60 #define TCSR_DIV_256 0x20 61 #define TCSR_DIV_1024 0x28 62 63 /* timers and PWMs */ 64 #define JZ_TC_TER 0x10002010 /* TC enable reg, ro */ 65 #define JZ_TC_TESR 0x10002014 /* TC enable set reg. */ 66 #define TESR_TCST0 0x0001 /* enable counter 0 */ 67 #define TESR_TCST1 0x0002 /* enable counter 1 */ 68 #define TESR_TCST2 0x0004 /* enable counter 2 */ 69 #define TESR_TCST3 0x0008 /* enable counter 3 */ 70 #define TESR_TCST4 0x0010 /* enable counter 4 */ 71 #define TESR_TCST5 0x0020 /* enable counter 5 */ 72 #define TESR_TCST6 0x0040 /* enable counter 6 */ 73 #define TESR_TCST7 0x0080 /* enable counter 7 */ 74 #define TESR_OST 0x8000 /* enable OST */ 75 #define JZ_TC_TECR 0x10002018 /* TC enable clear reg. */ 76 #define JZ_TC_TFR 0x10002020 77 #define TFR_FFLAG0 0x00000001 /* channel 0 */ 78 #define TFR_FFLAG1 0x00000002 /* channel 1 */ 79 #define TFR_FFLAG2 0x00000004 /* channel 2 */ 80 #define TFR_FFLAG3 0x00000008 /* channel 3 */ 81 #define TFR_FFLAG4 0x00000010 /* channel 4 */ 82 #define TFR_FFLAG5 0x00000020 /* channel 5 */ 83 #define TFR_FFLAG6 0x00000040 /* channel 6 */ 84 #define TFR_FFLAG7 0x00000080 /* channel 7 */ 85 #define TFR_OSTFLAG 0x00008000 /* OS timer */ 86 #define JZ_TC_TFSR 0x10002024 /* timer flag set */ 87 #define JZ_TC_TFCR 0x10002028 /* timer flag clear */ 88 #define JZ_TC_TMR 0x10002030 /* timer flag mask */ 89 #define JZ_TC_TMSR 0x10002034 /* timer flag mask set */ 90 #define JZ_TC_TMCR 0x10002038 /* timer flag mask clear*/ 91 92 #define JZ_TC_TDFR(n) (0x10002040 + (n * 0x10)) /* FULL compare */ 93 #define JZ_TC_TDHR(n) (0x10002044 + (n * 0x10)) /* HALF compare */ 94 #define JZ_TC_TCNT(n) (0x10002048 + (n * 0x10)) /* count */ 95 96 #define JZ_TC_TCSR(n) (0x1000204c + (n * 0x10)) 97 /* same bits as in JZ_WDOG_TCSR */ 98 99 /* operating system timer */ 100 #define JZ_OST_DATA 0x100020e0 /* compare */ 101 #define JZ_OST_CNT_LO 0x100020e4 102 #define JZ_OST_CNT_HI 0x100020e8 103 #define JZ_OST_CTRL 0x100020ec 104 #define OSTC_PCK_EN 0x0001 /* use PCLK */ 105 #define OSTC_RTC_EN 0x0002 /* use RTCCLK */ 106 #define OSTC_EXT_EN 0x0004 /* use EXTCLK */ 107 #define OSTC_PRESCALE_M 0x0038 108 #define OSTC_DIV_1 0x0000 109 #define OSTC_DIV_4 0x0008 110 #define OSTC_DIV_16 0x0010 111 #define OSTC_DIV_64 0x0018 112 #define OSTC_DIV_256 0x0020 113 #define OSTC_DIV_1024 0x0028 114 #define OSTC_SHUTDOWN 0x0200 115 #define OSTC_MODE 0x8000 /* 0 - reset to 0 when = OST_DATA */ 116 #define JZ_OST_CNT_U32 0x100020fc /* copy of CNT_HI when reading CNT_LO */ 117 118 static inline void 119 writereg(uint32_t reg, uint32_t val) 120 { 121 *(int32_t *)MIPS_PHYS_TO_KSEG1(reg) = val; 122 wbflush(); 123 } 124 125 static inline uint32_t 126 readreg(uint32_t reg) 127 { 128 wbflush(); 129 return *(int32_t *)MIPS_PHYS_TO_KSEG1(reg); 130 } 131 132 /* extra CP0 registers */ 133 static inline uint32_t 134 MFC0(uint32_t r, uint32_t s) 135 { 136 uint32_t ret = 0x12345678; 137 138 __asm volatile("mfc0 %0, $%1, %2; nop;" : "=r"(ret) : "i"(r), "i"(s)); 139 return ret; 140 } 141 142 #define MTC0(v, r, s) __asm volatile("mtc0 %0, $%1, %2; nop;" :: "r"(v), "i"(r), "i"(s)) 143 144 #define CP0_CORE_CTRL 12 /* select 2 */ 145 #define CC_SW_RST0 1 /* reset core 0 */ 146 #define CC_SW_RST1 2 /* reset core 1 */ 147 #define CC_RPC0 0x100 /* dedicater reset entry core 0 */ 148 #define CC_RPC1 0x200 /* -- || -- core 1 */ 149 #define CC_SLEEP0M 0x10000 /* mask sleep core 0 */ 150 #define CC_SLEEP1M 0x20000 /* mask sleep core 1 */ 151 152 /* cores status, 12 select 3 */ 153 #define CS_MIRQ0_P 0x00001 /* mailbox IRQ for 0 pending */ 154 #define CS_MIRQ1_P 0x00002 /* || core 1 */ 155 #define CS_IRQ0_P 0x00100 /* peripheral IRQ for core 0 */ 156 #define CS_IRQ1_P 0x00200 /* || core 1 */ 157 #define CS_SLEEP0 0x10000 /* core 0 sleeping */ 158 #define CS_SLEEP1 0x20000 /* core 1 sleeping */ 159 160 /* cores reset entry & IRQ masks - 12 select 4 */ 161 #define REIM_MIRQ0_M 0x00001 /* allow mailbox IRQ for core 0 */ 162 #define REIM_MIRQ1_M 0x00002 /* allow mailbox IRQ for core 1 */ 163 #define REIM_IRQ0_M 0x00100 /* allow peripheral IRQ for core 0 */ 164 #define REIM_IRQ1_M 0x00200 /* allow peripheral IRQ for core 1 */ 165 #define REIM_ENTRY_M 0xffff0000 /* reset exception entry if RPCn=1 */ 166 167 #define CP0_CORE_MBOX 20 /* select 0 for core 0, 1 for 1 */ 168 169 /* power management */ 170 #define JZ_CPCCR 0x10000000 /* Clock Control Register */ 171 #define JZ_PDIV_M 0x000f0000 /* PCLK divider mask */ 172 #define JZ_PDIV_S 16 /* PCLK divider shift */ 173 #define JZ_CPMPCR 0x00000014 /* MPLL */ 174 #define JZ_PLLM_S 19 /* PLL multiplier shift */ 175 #define JZ_PLLM_M 0xfff80000 /* PLL multiplier mask */ 176 #define JZ_PLLN_S 13 /* PLL divider shift */ 177 #define JZ_PLLN_M 0x0007e000 /* PLL divider mask */ 178 #define JZ_PLLP_S 9 /* PLL postdivider shift */ 179 #define JZ_PLLP_M 0x00001700 /* PLL postdivider mask */ 180 #define JZ_PLLON 0x00000010 /* PLL is on and stable */ 181 #define JZ_PLLBP 0x00000002 /* PLL bypass */ 182 #define JZ_PLLEN 0x00000001 /* PLL enable */ 183 #define JZ_CLKGR0 0x10000020 /* CLocK Gating Registers */ 184 #define JZ_OPCR 0x10000024 /* Oscillator Power Control Reg. */ 185 #define OPCR_IDLE_DIS 0x80000000 /* don't stop CPU clk on idle */ 186 #define OPCR_GPU_CLK_ST 0x40000000 /* stop GPU clock */ 187 #define OPCR_L2CM_M 0x0c000000 188 #define OPCR_L2CM_ON 0x00000000 /* L2 stays on in sleep */ 189 #define OPCR_L2CM_RET 0x04000000 /* L2 retention mode in sleep */ 190 #define OPCR_L2CM_OFF 0x08000000 /* L2 powers down in sleep */ 191 #define OPCR_SPENDN0 0x00000080 /* OTG port forced down */ 192 #define OPCR_SPENDN1 0x00000040 /* UHC port forced down */ 193 #define OPCR_BUS_MODE 0x00000020 /* 1 - bursts */ 194 #define OPCR_O1SE 0x00000010 /* EXTCLK on in sleep */ 195 #define OPCR_PD 0x00000008 /* P0 down in sleep */ 196 #define OPCR_ERCS 0x00000004 /* 1 RTCCLK, 0 EXTCLK/512 */ 197 #define OPCR_CPU_MODE 0x00000002 /* 1 access 'accelerated' */ 198 #define OPCR_OSE 0x00000001 /* disable EXTCLK */ 199 #define JZ_CLKGR1 0x10000028 /* CLocK Gating Registers */ 200 #define JZ_USBPCR 0x1000003c 201 #define PCR_USB_MODE 0x80000000 /* 1 - otg */ 202 #define PCR_AVLD_REG 0x40000000 203 #define PCR_IDPULLUP_MASK 0x30000000 204 #define PCR_INCR_MASK 0x08000000 205 #define PCR_TCRISETUNE 0x04000000 206 #define PCR_COMMONONN 0x02000000 207 #define PCR_VBUSVLDEXT 0x01000000 208 #define PCR_VBUSVLDEXTSEL 0x00800000 209 #define PCR_POR 0x00400000 210 #define PCR_SIDDQ 0x00200000 211 #define PCR_OTG_DISABLE 0x00100000 212 #define PCR_COMPDISTN_M 0x000e0000 213 #define PCR_OTGTUNE 0x0001c000 214 #define PCR_SQRXTUNE 0x00003800 215 #define PCR_TXFSLSTUNE 0x00000780 216 #define PCR_TXPREEMPHTUNE 0x00000040 217 #define PCR_TXHSXVTUNE 0x00000030 218 #define PCR_TXVREFTUNE 0x0000000f 219 #define JZ_USBRDT 0x10000040 /* Reset Detect Timer Register */ 220 #define JZ_USBPCR1 0x10000048 221 #define PCR_SYNOPSYS 0x10000000 /* Mentor mode otherwise */ 222 #define PCR_REFCLK_CORE 0x0c000000 223 #define PCR_REFCLK_XO25 0x04000000 224 #define PCR_REFCLK_CO 0x00000000 225 #define PCR_CLK_M 0x03000000 /* clock */ 226 #define PCR_CLK_192 0x03000000 /* 19.2MHz */ 227 #define PCR_CLK_48 0x02000000 /* 48MHz */ 228 #define PCR_CLK_24 0x01000000 /* 24MHz */ 229 #define PCR_CLK_12 0x00000000 /* 12MHz */ 230 #define PCR_DMPD1 0x00800000 /* pull down D- on port 1 */ 231 #define PCR_DPPD1 0x00400000 /* pull down D+ on port 1 */ 232 #define PCR_PORT0_RST 0x00200000 /* port 0 reset */ 233 #define PCR_PORT1_RST 0x00100000 /* port 1 reset */ 234 #define PCR_WORD_I_F0 0x00080000 /* 1: 16bit/30M, 8/60 otherw. */ 235 #define PCR_WORD_I_F1 0x00040000 /* same for port 1 */ 236 #define PCR_COMPDISTUNE 0x00038000 /* disconnect threshold */ 237 #define PCR_SQRXTUNE1 0x00007000 /* squelch threshold */ 238 #define PCR_TXFSLSTUNE1 0x00000f00 /* FS/LS impedance adj. */ 239 #define PCR_TXPREEMPH 0x00000080 /* HS transm. pre-emphasis */ 240 #define PCR_TXHSXVTUNE1 0x00000060 /* dp/dm voltage adj. */ 241 #define PCR_TXVREFTUNE1 0x00000017 /* HS DC voltage adj. */ 242 #define PCR_TXRISETUNE1 0x00000001 /* rise/fall wave adj. */ 243 244 #define JZ_UHCCDR 0x1000006c /* UHC Clock Divider Register */ 245 #define JZ_SPCR0 0x100000b8 /* SRAM Power Control Registers */ 246 #define JZ_SPCR1 0x100000bc 247 #define JZ_SRBC 0x100000c4 /* Soft Reset & Bus Control */ 248 249 /* interrupt controller */ 250 #define JZ_ICSR0 0x10001000 /* raw IRQ line status */ 251 #define JZ_ICMR0 0x10001004 /* IRQ mask, 1 masks IRQ */ 252 #define JZ_ICMSR0 0x10001008 /* sets bits in mask register */ 253 #define JZ_ICMCR0 0x1000100c /* clears bits in mask register */ 254 #define JZ_ICPR0 0x10001010 /* line status after masking */ 255 256 #define JZ_ICSR1 0x10001020 /* raw IRQ line status */ 257 #define JZ_ICMR1 0x10001024 /* IRQ mask, 1 masks IRQ */ 258 #define JZ_ICMSR1 0x10001028 /* sets bits in mask register */ 259 #define JZ_ICMCR1 0x1000102c /* clears bits in maks register */ 260 #define JZ_ICPR1 0x10001030 /* line status after masking */ 261 262 #define JZ_DSR0 0x10001034 /* source for PDMA */ 263 #define JZ_DMR0 0x10001038 /* mask for PDMA */ 264 #define JZ_DPR0 0x1000103c /* pending for PDMA */ 265 266 #define JZ_DSR1 0x10001040 /* source for PDMA */ 267 #define JZ_DMR1 0x10001044 /* mask for PDMA */ 268 #define JZ_DPR1 0x10001048 /* pending for PDMA */ 269 270 /* memory controller */ 271 #define JZ_DMMAP0 0x13010024 272 #define JZ_DMMAP1 0x13010028 273 #define DMMAP_BASE 0x0000ff00 /* base PADDR of memory chunk */ 274 #define DMMAP_MASK 0x000000ff /* mask which bits of PADDR are 275 * constant */ 276 /* USB controllers */ 277 #define JZ_EHCI_BASE 0x13490000 278 #define JZ_OHCI_BASE 0x134a0000 279 #define JZ_DWC2_BASE 0x13500000 280 281 /* Ethernet */ 282 #define JZ_DME_BASE 0x16000000 283 #define JZ_DME_IO 0 284 #define JZ_DME_DATA 2 285 286 /* GPIO */ 287 #define JZ_GPIO_A_BASE 0x10010000 288 #define JZ_GPIO_B_BASE 0x10010100 289 #define JZ_GPIO_C_BASE 0x10010200 290 #define JZ_GPIO_D_BASE 0x10010300 291 #define JZ_GPIO_E_BASE 0x10010400 292 #define JZ_GPIO_F_BASE 0x10010500 293 294 /* GPIO registers per port */ 295 #define JZ_GPIO_PIN 0x00000000 /* pin level register */ 296 /* 0 - normal gpio, 1 - interrupt */ 297 #define JZ_GPIO_INT 0x00000010 /* interrupt register */ 298 #define JZ_GPIO_INTS 0x00000014 /* interrupt set register */ 299 #define JZ_GPIO_INTC 0x00000018 /* interrupt clear register */ 300 /* 301 * INT == 1: 1 disables interrupt 302 * INT == 0: device select, see below 303 */ 304 #define JZ_GPIO_MASK 0x00000020 /* port mask register */ 305 #define JZ_GPIO_MASKS 0x00000024 /* port mask set register */ 306 #define JZ_GPIO_MASKC 0x00000028 /* port mask clear register */ 307 /* 308 * INT == 1: 0 - level triggered, 1 - edge triggered 309 * INT == 0: 0 - device select, see below 310 */ 311 #define JZ_GPIO_PAT1 0x00000030 /* pattern 1 register */ 312 #define JZ_GPIO_PAT1S 0x00000034 /* pattern 1 set register */ 313 #define JZ_GPIO_PAT1C 0x00000038 /* pattern 1 clear register */ 314 /* 315 * INT == 1: 316 * PAT1 == 0: 0 - trigger on low, 1 - trigger on high 317 * PAT1 == 1: 0 - trigger on falling edge, 1 - trigger on rising edge 318 * INT == 0: 319 * MASK == 0: 320 * PAT1 == 0: 0 - device 0, 1 - device 1 321 * PAT1 == 1: 0 - device 2, 1 - device 3 322 * MASK == 1: 323 * PAT1 == 0: set gpio output 324 * PAT1 == 1: pin is input 325 */ 326 #define JZ_GPIO_PAT0 0x00000040 /* pattern 0 register */ 327 #define JZ_GPIO_PAT0S 0x00000044 /* pattern 0 set register */ 328 #define JZ_GPIO_PAT0C 0x00000048 /* pattern 0 clear register */ 329 /* 1 - interrupt happened */ 330 #define JZ_GPIO_FLAG 0x00000050 /* flag register */ 331 #define JZ_GPIO_FLAGC 0x00000058 /* flag clear register */ 332 /* 1 - disable pull up/down resistors */ 333 #define JZ_GPIO_DPULL 0x00000070 /* pull disable register */ 334 #define JZ_GPIO_DPULLS 0x00000074 /* pull disable set register */ 335 #define JZ_GPIO_DPULLC 0x00000078 /* pull disable clear register */ 336 /* the following are uncommented in the manual */ 337 #define JZ_GPIO_DRVL 0x00000080 /* drive low register */ 338 #define JZ_GPIO_DRVLS 0x00000084 /* drive low set register */ 339 #define JZ_GPIO_DRVLC 0x00000088 /* drive low clear register */ 340 #define JZ_GPIO_DIR 0x00000090 /* direction register */ 341 #define JZ_GPIO_DIRS 0x00000094 /* direction register */ 342 #define JZ_GPIO_DIRC 0x00000098 /* direction register */ 343 #define JZ_GPIO_DRVH 0x000000a0 /* drive high register */ 344 #define JZ_GPIO_DRVHS 0x000000a4 /* drive high set register */ 345 #define JZ_GPIO_DRVHC 0x000000a8 /* drive high clear register */ 346 347 static inline void 348 gpio_as_output(uint32_t g, int pin) 349 { 350 uint32_t mask = 1 << pin; 351 uint32_t reg = JZ_GPIO_A_BASE + (g << 8); 352 353 writereg(reg + JZ_GPIO_INTC, mask); /* use as gpio */ 354 writereg(reg + JZ_GPIO_MASKS, mask); 355 writereg(reg + JZ_GPIO_PAT1C, mask); /* make output */ 356 } 357 358 static inline void 359 gpio_set(uint32_t g, int pin, int level) 360 { 361 uint32_t mask = 1 << pin; 362 uint32_t reg = JZ_GPIO_A_BASE + (g << 8); 363 364 reg += (level == 0) ? JZ_GPIO_PAT0C : JZ_GPIO_PAT0S; 365 writereg(reg, mask); 366 } 367 368 static inline void 369 gpio_as_dev0(uint32_t g, int pin) 370 { 371 uint32_t mask = 1 << pin; 372 uint32_t reg = JZ_GPIO_A_BASE + (g << 8); 373 374 writereg(reg + JZ_GPIO_INTC, mask); /* use as gpio */ 375 writereg(reg + JZ_GPIO_MASKC, mask); /* device mode */ 376 writereg(reg + JZ_GPIO_PAT1C, mask); /* select 0 */ 377 writereg(reg + JZ_GPIO_PAT0C, mask); 378 } 379 380 static inline void 381 gpio_as_dev1(uint32_t g, int pin) 382 { 383 uint32_t mask = 1 << pin; 384 uint32_t reg = JZ_GPIO_A_BASE + (g << 8); 385 386 writereg(reg + JZ_GPIO_INTC, mask); /* use as gpio */ 387 writereg(reg + JZ_GPIO_MASKC, mask); /* device mode */ 388 writereg(reg + JZ_GPIO_PAT1C, mask); /* select 1 */ 389 writereg(reg + JZ_GPIO_PAT0S, mask); 390 } 391 392 static inline void 393 gpio_as_dev2(uint32_t g, int pin) 394 { 395 uint32_t mask = 1 << pin; 396 uint32_t reg = JZ_GPIO_A_BASE + (g << 8); 397 398 writereg(reg + JZ_GPIO_INTC, mask); /* use as gpio */ 399 writereg(reg + JZ_GPIO_MASKC, mask); /* device mode */ 400 writereg(reg + JZ_GPIO_PAT1S, mask); /* select 2 */ 401 writereg(reg + JZ_GPIO_PAT0C, mask); 402 } 403 404 static inline void 405 gpio_as_dev3(uint32_t g, int pin) 406 { 407 uint32_t mask = 1 << pin; 408 uint32_t reg = JZ_GPIO_A_BASE + (g << 8); 409 410 writereg(reg + JZ_GPIO_INTC, mask); /* use as gpio */ 411 writereg(reg + JZ_GPIO_MASKC, mask); /* device mode */ 412 writereg(reg + JZ_GPIO_PAT1S, mask); /* select 3 */ 413 writereg(reg + JZ_GPIO_PAT0S, mask); 414 } 415 416 static inline void 417 gpio_as_intr_level(uint32_t g, int pin) 418 { 419 uint32_t mask = 1 << pin; 420 uint32_t reg = JZ_GPIO_A_BASE + (g << 8); 421 422 writereg(reg + JZ_GPIO_MASKS, mask); /* mask it */ 423 writereg(reg + JZ_GPIO_INTS, mask); /* use as interrupt */ 424 writereg(reg + JZ_GPIO_PAT1C, mask); /* level trigger */ 425 writereg(reg + JZ_GPIO_PAT0S, mask); /* trigger on high */ 426 writereg(reg + JZ_GPIO_FLAGC, mask); /* clear it */ 427 writereg(reg + JZ_GPIO_MASKC, mask); /* enable it */ 428 } 429 430 /* I2C / SMBus */ 431 #define JZ_SMB0_BASE 0x10050000 432 #define JZ_SMB1_BASE 0x10051000 433 #define JZ_SMB2_BASE 0x10052000 434 #define JZ_SMB3_BASE 0x10053000 435 #define JZ_SMB4_BASE 0x10054000 436 437 /* SMBus register offsets, per port */ 438 #define JZ_SMBCON 0x00 /* SMB control */ 439 #define JZ_STPHLD 0x80 /* Stop Hold Enable bit */ 440 #define JZ_SLVDIS 0x40 /* 1 - slave disabled */ 441 #define JZ_REST 0x20 /* 1 - allow RESTART */ 442 #define JZ_MATP 0x10 /* 1 - enable 10bit addr. for master */ 443 #define JZ_SATP 0x08 /* 1 - enable 10bit addr. for slave */ 444 #define JZ_SPD_M 0x06 /* bus speed control */ 445 #define JZ_SPD_100KB 0x02 /* 100kBit/s mode */ 446 #define JZ_SPD_400KB 0x04 /* 400kBit/s mode */ 447 #define JZ_MD 0x01 /* enable master */ 448 #define JZ_SMBTAR 0x04 /* SMB target address */ 449 #define JZ_SMATP 0x1000 /* enable 10bit master addr */ 450 #define JZ_SPECIAL 0x0800 /* 1 - special command */ 451 #define JZ_START 0x0400 /* 1 - send START */ 452 #define JZ_SMBTAR_M 0x03ff /* target address */ 453 #define JZ_SMBSAR 0x08 /* SMB slave address */ 454 #define JZ_SMBDC 0x10 /* SMB data buffer and command */ 455 #define JZ_CMD 0x100 /* 1 - read, 0 - write */ 456 #define JZ_DATA 0x0ff 457 #define JZ_SMBSHCNT 0x14 /* Standard speed SMB SCL high count */ 458 #define JZ_SMBSLCNT 0x18 /* Standard speed SMB SCL low count */ 459 #define JZ_SMBFHCNT 0x1C /* Fast speed SMB SCL high count */ 460 #define JZ_SMBFLCNT 0x20 /* Fast speed SMB SCL low count */ 461 #define JZ_SMBINTST 0x2C /* SMB Interrupt Status */ 462 #define JZ_ISTT 0x400 /* START or RESTART occured */ 463 #define JZ_ISTP 0x200 /* STOP occured */ 464 #define JZ_TXABT 0x40 /* ABORT occured */ 465 #define JZ_TXEMP 0x10 /* TX FIFO is low */ 466 #define JZ_TXOF 0x08 /* TX FIFO is high */ 467 #define JZ_RXFL 0x04 /* RX FIFO is at JZ_SMBRXTL*/ 468 #define JZ_RXOF 0x02 /* RX FIFO is high */ 469 #define JZ_RXUF 0x01 /* RX FIFO underflow */ 470 #define JZ_SMBINTM 0x30 /* SMB Interrupt Mask */ 471 #define JZ_SMBRXTL 0x38 /* SMB RxFIFO Threshold */ 472 #define JZ_SMBTXTL 0x3C /* SMB TxFIFO Threshold */ 473 #define JZ_SMBCINT 0x40 /* Clear Interrupts */ 474 #define JZ_CLEARALL 0x01 475 #define JZ_SMBCRXUF 0x44 /* Clear RXUF Interrupt */ 476 #define JZ_SMBCRXOF 0x48 /* Clear RX_OVER Interrupt */ 477 #define JZ_SMBCTXOF 0x4C /* Clear TX_OVER Interrupt */ 478 #define JZ_SMBCRXREQ 0x50 /* Clear RDREQ Interrupt */ 479 #define JZ_SMBCTXABT 0x54 /* Clear TX_ABRT Interrupt */ 480 #define JZ_SMBCRXDN 0x58 /* Clear RX_DONE Interrupt */ 481 #define JZ_SMBCACT 0x5c /* Clear ACTIVITY Interrupt */ 482 #define JZ_SMBCSTP 0x60 /* Clear STOP Interrupt */ 483 #define JZ_SMBCSTT 0x64 /* Clear START Interrupt */ 484 #define JZ_SMBCGC 0x68 /* Clear GEN_CALL Interrupt */ 485 #define JZ_SMBENB 0x6C /* SMB Enable */ 486 #define JZ_ENABLE 0x01 487 #define JZ_SMBST 0x70 /* SMB Status register */ 488 #define JZ_SLVACT 0x40 /* slave is active */ 489 #define JZ_MSTACT 0x20 /* master is active */ 490 #define JZ_RFF 0x10 /* RX FIFO is full */ 491 #define JZ_RFNE 0x08 /* RX FIFO not empty */ 492 #define JZ_TFE 0x04 /* TX FIFO is empty */ 493 #define JZ_TFNF 0x02 /* TX FIFO is not full */ 494 #define JZ_ACT 0x01 /* JZ_SLVACT | JZ_MSTACT */ 495 #define JZ_SMBABTSRC 0x80 /* SMB Transmit Abort Status Register */ 496 #define JZ_SMBDMACR 0x88 /* DMA Control Register */ 497 #define JZ_SMBDMATDL 0x8c /* DMA Transmit Data Level */ 498 #define JZ_SMBDMARDL 0x90 /* DMA Receive Data Level */ 499 #define JZ_SMBSDASU 0x94 /* SMB SDA Setup Register */ 500 #define JZ_SMBACKGC 0x98 /* SMB ACK General Call Register */ 501 #define JZ_SMBENBST 0x9C /* SMB Enable Status Register */ 502 #define JZ_SMBSDAHD 0xD0 /* SMB SDA HolD time Register */ 503 #define JZ_HDENB 0x100 /* enable hold time */ 504 505 #endif /* INGENIC_REGS_H */ 506
Indexes created Wed Oct 01 15:09:59 GMT 2025