GENERIC revision 1.162
1# $NetBSD: GENERIC,v 1.162 2004/08/01 10:45:23 mrg Exp $ 2# 3# GENERIC machine description file 4# 5# This machine description file is used to generate the default NetBSD 6# kernel. The generic kernel does not include all options, subsystems 7# and device drivers, but should be useful for most applications. 8# 9# The machine description file can be customised for your specific 10# machine to reduce the kernel size and improve its performance. 11# 12# For further information on compiling NetBSD kernels, see the config(8) 13# man page. 14# 15# For further information on hardware support for this architecture, see 16# the intro(4) man page. For further information about kernel options 17# for this architecture, see the options(4) man page. For an explanation 18# of each device driver in this file see the section 4 man page for the 19# device. 20 21include "arch/sparc/conf/std.sparc" 22 23options INCLUDE_CONFIG_FILE # embed config file in kernel binary 24 25#ident "GENERIC-$Revision: 1.162 $" 26 27maxusers 32 28 29## System kernel configuration. See options(4) for more detail. 30 31 32# Options for variants of the Sun SPARC architecure. 33# We currently support three architecture types; at least one is required. 34options SUN4 # sun4/100, sun4/200, sun4/300 35options SUN4C # sun4c - SS1, 1+, 2, ELC, SLC, IPC, IPX, etc. 36options SUN4M # sun4m - SS10, SS20, Classic, etc. 37options SUN4D # sun4d - SS1000, SC2000 38 39options SUN4_MMU3L # sun4/400 3-level MMU 40 41## System options specific to the sparc machine type 42 43# Blink the power LED on some machines to indicate the system load. 44#options BLINK 45 46## Use a faster console than the PROM's slow drawing routines. Not needed 47## for headless (no framebuffer) machines. 48options RASTERCONSOLE # fast rasterop console 49options FONT_GALLANT12x22 # the console font 50#options FONT_BOLD8x16 # a somewhat smaller font 51## default console colors: black-on-white; this can be changed 52## using the following two options. 53#options RASTERCONSOLE_FGCOL=WSCOL_BLACK 54#options RASTERCONSOLE_BGCOL=WSCOL_WHITE 55 56#### System options that are the same for all ports 57 58## Root device configuration: change the ?'s if you are going to use a 59## nonstandard root partition (other than where the kernel is booted from) 60## and/or nonstandard root type (not ffs or nfs). Normally this can be 61## automagically determined at boot time. 62 63config netbsd root on ? type ? 64 65## System call tracing (see ktrace(1)). 66options KTRACE 67options SYSTRACE # system call vetting via systrace(1) 68 69## Collect statistics on kernel malloc's and free's. This does have a 70## significant performance hit on slower machines, so it is intended for 71## diagnostic use only. 72#options KMEMSTATS 73 74## System V compatible IPC subsystem. (msgctl(2), semctl(2), and shmctl(2)) 75options SYSVMSG # System V message queues 76options SYSVSEM # System V semaphores 77#options SEMMNI=10 # number of semaphore identifiers 78#options SEMMNS=60 # number of semaphores in system 79#options SEMUME=10 # max number of undo entries per process 80#options SEMMNU=30 # number of undo structures in system 81options SYSVSHM # System V shared memory 82#options SHMMAXPGS=1024 # 1024 pages is the default 83options P1003_1B_SEMAPHORE # p1003.1b semaphore support 84 85## Loadable kernel module support; still under development. 86options LKM 87 88options USERCONF # userconf(4) support 89#options PIPE_SOCKETPAIR # smaller, but slower pipe(2) 90options SYSCTL_INCLUDE_DESCR # Include sysctl descriptions in kernel 91 92# Enable experimental buffer queue strategy for better responsiveness under 93# high disk I/O load. Use it with caution - it's not proven to be stable yet. 94#options NEW_BUFQ_STRATEGY 95 96## NFS boot options; tries DHCP/BOOTP then BOOTPARAM 97options NFS_BOOT_BOOTPARAM 98#options NFS_BOOT_BOOTP 99options NFS_BOOT_DHCP 100 101#### Debugging options 102 103## The DDB in-kernel debugger runs at panic (unless DDB_ONPANIC=0), or at 104## serial console break or keyboard reset, where the PROM would normally 105## intercept. DDB_HISTORY_SIZE adds up/down arrow command history. 106#options DDB # kernel dynamic debugger 107#options DDB_HISTORY_SIZE=100 # enable history editing in DDB 108#options DDB_ONPANIC=1 # see also sysctl(8): `ddb.onpanic' 109 110## You may also use gdb, on another computer connected to this machine over 111## a serial port. Both KGDB_DEV and KGDB_DEVRATE should be specified; 112## KGDB_DEV is a dev_t encoded device number of the serial port to use, where 113## the minor device number encodes the PROM enumeration of the serial ports, 114## i.e.: 115## 0xc00 = ttya, 0xc01 = ttyb, 0xc02 = ttyc, 0xc03 = ttyd. 116## (Note: ttyc and ttyd are available only on some sun4 models) 117#options KGDB # support for kernel gdb 118#options KGDB_DEV=0xc01 # kgdb device number (this is `ttyb') 119#options KGDB_DEVRATE=38400 # baud rate 120 121 122## Compile the kernel with debugging symbols (`netbsd.gdb' is the debug file), 123## such that gdb(1) can be used on a kernel coredump. 124 125#makeoptions DEBUG="-g" 126 127 128## Adds code to the kernel that does internal consistency checks, and will 129## cause the kernel to panic if corruption of internal data structures 130## is detected. 131#options DIAGNOSTIC # extra kernel sanity checking 132 133## Enable (possibly expensive) debugging code that may also display messages 134## on the system console 135#options DEBUG 136 137## Make SCSI error messages more verbose when explaining their meanings. 138options SCSIVERBOSE 139 140options MIIVERBOSE # verbose PHY autoconfig messages 141 142## `INSECURE' turns off the kernel security level (securelevel = 0 always). 143## This allows writing to /dev/mem, loading kernel modules while multi-user, 144## and other insecurities good only for development work. Do not use this 145## option on a production machine. 146#options INSECURE 147 148## `FDSCRIPTS' allows non-readable but executable scripts by providing a 149## pre-opened opaque file to the script interpreter. `SETUIDSCRIPTS', 150## which implies FDSCRIPTS, allows scripts to be set-user-id using the same 151## opaque file mechanism. Perl calls this "secure setuid scripts." 152 153#options FDSCRIPTS 154#options SETUIDSCRIPTS 155 156## Options for compatibility with previous releases foreign system binaries. 157## In the cases of COMPAT_SUNOS and COMPAT_SVR4, you may need to set up 158## additional user-level utilities or system configuration files. See 159## compat_sunos(8) and compat_svr4(8). 160 161options COMPAT_43 # 4.3BSD system interfaces 162options COMPAT_10 # NetBSD 1.0 binary compatibility 163options COMPAT_11 # NetBSD 1.1 binary compatibility 164options COMPAT_12 # NetBSD 1.2 binary compatibility 165options COMPAT_13 # NetBSD 1.3 binary compatibility 166options COMPAT_14 # NetBSD 1.4 binary compatibility 167options COMPAT_16 # NetBSD 1.6 binary compatibility 168options COMPAT_20 # NetBSD 2.0 binary compatibility 169options COMPAT_SUNOS # SunOS 4.x binary compatibility 170options COMPAT_SVR4 # SunOS 5.x binary compatibility 171 172## File systems. You probably need at least one of FFS or NFS. 173file-system FFS # Berkeley Fast Filesystem 174file-system NFS # Sun NFS-compatible filesystem client 175file-system KERNFS # kernel data-structure filesystem 176file-system NULLFS # NULL layered filesystem 177file-system OVERLAY # overlay file system 178file-system MFS # memory-based filesystem 179file-system FDESC # user file descriptor filesystem 180file-system UMAPFS # uid/gid remapping filesystem 181file-system LFS # Log-based filesystem (still experimental) 182file-system PORTAL # portal filesystem (still experimental) 183file-system PROCFS # /proc 184file-system CD9660 # ISO 9660 + Rock Ridge file system 185file-system UNION # union file system 186file-system MSDOSFS # MS-DOS FAT filesystem(s). 187file-system CODA # Coda File System; also needs vcoda (below) 188 189## File system options. 190options NFSSERVER # Sun NFS-compatible filesystem server 191options QUOTA # FFS quotas 192#options FFS_EI # FFS Endian Independent support 193options SOFTDEP # FFS soft updates support. 194 195## Network protocol support. In most environments, INET is required. 196options INET # IP (Internet Protocol) v4 197options INET6 # IPV6 198#options IPSEC # IP security 199#options IPSEC_ESP # IP security (encryption part; define w/IPSEC) 200#options IPSEC_DEBUG # debug for IP security 201#options GATEWAY # packet forwarding ("router switch") 202#options MROUTING # packet forwarding of multicast packets 203#options DIRECTED_BROADCAST # allow broadcasts through routers 204options NS # Xerox NS networking 205#options NSIP # Xerox NS tunneling over IP 206options ISO,TPIP # OSI networking 207#options EON # OSI tunneling over IP 208#options CCITT,LLC,HDLC # X.25 packet switched protocol 209#options NETATALK # AppleTalk (over Ethernet) protocol 210options NTP # Network Time Protocol in-kernel support 211#options PPS_SYNC # Add serial line synchronization for NTP 212options PFIL_HOOKS # Add pfil(9) hooks, intended for custom LKMs. 213options IPFILTER_LOG # Add ipmon(8) logging for ipfilter device 214#options IPFILTER_DEFAULT_BLOCK # block all packets by default 215options PPP_BSDCOMP # Add BSD compression to ppp device 216options PPP_DEFLATE # Add deflate (libz) compression to ppp device 217options PPP_FILTER # Add active filters for ppp (via bpf) 218 219#options ALTQ # Manipulate network interfaces' output queues 220#options ALTQ_BLUE # Stochastic Fair Blue 221#options ALTQ_CBQ # Class-Based Queueing 222#options ALTQ_CDNR # Diffserv Traffic Conditioner 223#options ALTQ_FIFOQ # First-In First-Out Queue 224#options ALTQ_FLOWVALVE # RED/flow-valve (red-penalty-box) 225#options ALTQ_HFSC # Hierarchical Fair Service Curve 226#options ALTQ_LOCALQ # Local queueing discipline 227#options ALTQ_PRIQ # Priority Queueing 228#options ALTQ_RED # Random Early Detection 229#options ALTQ_RIO # RED with IN/OUT 230#options ALTQ_WFQ # Weighted Fair Queueing 231 232 233 234#### Main bus and CPU .. all systems. 235mainbus0 at root 236cpu0 at mainbus0 237cpuunit0 at mainbus0 # sun4d 238cpuunit* at mainbus0 # sun4d 239cpu0 at cpuunit0 # sun4d 240 241#### Bus types found on SPARC systems. 242 243sbus0 at mainbus0 # sun4c 244obio0 at mainbus0 # sun4 and sun4m 245sparcvme0 at mainbus0 # sun4 246iommu0 at mainbus0 # sun4m 247sbus0 at iommu0 # sun4m 248sparcvme0 at iommu0 # sun4m 249vme0 at sparcvme0 # MI VME attachment 250bootbus0 at cpuunit0 # sun4d 251bootbus* at cpuunit? # sun4d 252 253## SBus expander box 254xbox* at sbus? slot ? offset ? 255sbus* at xbox? 256 257## SBus to PCMCIA bridge 258nell* at sbus? slot ? offset ? # PCMCIA bridge 259pcmcia* at nell? 260 261#### Standard system devices -- all required for a given architecture 262 263## Auxiliary system registers on sun4c and sun4m 264auxreg0 at mainbus0 # sun4c 265auxreg0 at obio0 # sun4m 266auxiotwo0 at obio0 # only on Tadpole SPARCbook. 267 268## Power status and control register on Sun4m systems 269power0 at obio0 270 271## Mostek clock found on 4/300, sun4c, sun4m and sun4d systems. 272## The Mostek clock NVRAM is the "eeprom" on sun4/300 systems. 273clock0 at mainbus0 # sun4c 274clock0 at obio0 # sun4m 275clock0 at obio0 addr 0xf2000000 # sun4/300 276clock0 at bootbus0 # sun4d 277 278## Intersil clock found on 4/100 and 4/200 systems. 279oclock0 at obio0 addr 0xf3000000 # sun4/200 280oclock0 at obio0 addr 0x03000000 # sun4/100 281 282## Memory error registers. 283memreg0 at mainbus0 # sun4c 284memreg0 at obio0 # sun4m 285memreg0 at obio0 addr 0xf4000000 # sun4/200 and sun4/300 286memreg0 at obio0 addr 0x04000000 # sun4/100 287 288## ECC memory control 289eccmemctl0 at mainbus0 # sun4m 290 291## Timer chip found on 4/300, sun4c, and sun4m systems. 292timer0 at mainbus0 # sun4c 293timer0 at obio0 # sun4m 294timer0 at obio0 addr 0xef000000 # sun4/300 295 296## EEPROM found on 4/100 and 4/200 systems. Note that the 4/300 297## doesn't use this driver; the `EEPROM' is in the NVRAM on the 298## Mostek clock chip on 4/300 systems. 299eeprom0 at obio0 addr 0xf2000000 # sun4/200 300eeprom0 at obio0 addr 0x02000000 # sun4/100 301 302 303#### Serial port configuration 304 305## Zilog 8530 serial chips. Each has two-channels. 306## zs0 is ttya and ttyb. zs1 is the keyboard and mouse. 307zs0 at mainbus0 # sun4c 308zs0 at obio0 # sun4m 309zs0 at obio0 addr 0xf1000000 level 12 # sun4/200 and sun4/300 310zs0 at obio0 addr 0x01000000 level 12 # sun4/100 311zs0 at bootbus0 # sun4d 312zstty0 at zs0 channel 0 # ttya 313zstty1 at zs0 channel 1 # ttyb 314 315zs1 at mainbus0 # sun4c 316zs1 at obio0 # sun4m 317zs1 at obio0 addr 0xf0000000 level 12 # sun4/200 and sun4/300 318zs1 at obio0 addr 0x00000000 level 12 # sun4/100 319zs1 at bootbus0 # sun4d 320kbd0 at zs1 channel 0 # keyboard 321ms0 at zs1 channel 1 # mouse 322 323zs2 at obio0 addr 0xe0000000 level 12 # sun4/300 324zstty2 at zs2 channel 0 # ttyc 325zstty3 at zs2 channel 1 # ttyd 326 327zs* at bootbus? # sun4d 328zstty* at zs? 329 330## NS16x50 serial chips and clones. Present on the 331## Sun JavaStation-1 and Tadpole SPARCbook 3 332com* at obio0 # sun4m 333 334# Parallel port. 335bpp* at sbus? slot? offset ? 336 337## Magma Serial/Parallel driver 338magma* at sbus? slot ? offset ? 339mtty* at magma? 340mbpp* at magma? 341 342## SUNW,spif Serial/Parallel driver 343spif* at sbus? slot ? offset ? 344stty* at spif? 345sbpp* at spif? 346 347## PCMCIA serial interfaces 348#com* at pcmcia? 349#pcmcom* at pcmcia? 350#com* at pcmcom? 351 352#### Disk controllers and disks 353 354# 355 356## The following flags may be set for the NCR53c94 based esp driver: 357## bits 0-7: disable disconnect/reselect for the corresponding target 358## bits 8-15: disable synchronous negotiation for target [bit-8] 359 360## sun4/300, sun4c, sun4m on-board SCSI, and FSBE/S SBus SCSI cards. 361## Both `dma' and `esp' are needed in all cases. 362## Two kinds of additional SBus SCSI interfaces are available. One uses 363## "esp at sbus" like the sun4c on-board; the other uses "esp at dma". 364 365## sun4/300 SCSI - an NCR53c94 or equivalent behind 366## an LSI Logic DMA controller 367 368dma0 at obio0 addr 0xfa001000 level 4 # sun4/300 369esp0 at obio0 addr 0xfa000000 level 4 flags 0x0000 # sun4/300 370 371dma0 at sbus0 slot ? offset ? # sun4c/sun4m 372esp0 at sbus0 slot ? offset ? flags 0x0000 # sun4c 373esp0 at dma0 flags 0x0000 # sun4m 374 375# FSBE/S SCSI & SunSwift Sbus FAS366 376dma* at sbus? slot ? offset ? # SBus 377esp* at sbus? slot ? offset ? flags 0x0000 # SBus 378esp* at dma? flags 0x0000 # SBus 379 380scsibus* at esp? 381 382## Qlogic ISP SBus SCSI Card 383isp* at sbus? slot ? offset ? 384scsibus* at isp? 385 386## NCR5380-based "Sun SCSI 3" VME SCSI controller. 387## This driver has several flags which may be enabled by OR'ing 388## the values and using the "flags" directive. 389## Valid flags are: 390## 391## 0x01 Use DMA (may be polled) 392## 0x02 Use DMA completion interrupts 393## 0x04 Allow disconnect/reselect 394## 395## E.g. the following would enable DMA, interrupts, and reselect: 396## si0 at vme0 addr 0x200000 irq 3 vect 0x40 flags 0x07 397## 398## By default, DMA is enabled in the driver. 399 400si0 at vme0 addr 0x200000 irq 2 vect 0x40 401scsibus* at si? 402 403## NCR5380-based "SCSI Weird" on-board SCSI interface found 404## on sun4/100 systems. The flags are the same as the "si" 405## controller. Note, while DMA is enabled by default, only 406## polled DMA works at this time, and reselects do not work 407## on this particular controller. 408 409sw0 at obio0 addr 0x0a000000 level 3 410scsibus* at sw? 411 412## PCMCIA SCSI controllers 413#aic* at pcmcia? 414#scsibus* at aic? 415 416 417## These entries find devices on all SCSI busses and assign 418## unit numbers dynamically. 419sd* at scsibus? target ? lun ? # SCSI disks 420st* at scsibus? target ? lun ? # SCSI tapes 421cd* at scsibus? target ? lun ? # SCSI CD-ROMs 422ch* at scsibus? target ? lun ? # SCSI changer devices 423ss* at scsibus? target ? lun ? # SCSI scanners 424ses* at scsibus? target ? lun ? # SCSI SES/SAF-TE 425uk* at scsibus? target ? lun ? # unknown SCSI 426 427 428## Xylogics 753 or 7053 VME SMD disk controllers and disks, found 429## on sun4 systems. 430xdc0 at vme0 addr 0xee80 irq 3 vect 0x44 431xdc1 at vme0 addr 0xee90 irq 3 vect 0x45 432xdc2 at vme0 addr 0xeea0 irq 3 vect 0x46 433xdc3 at vme0 addr 0xeeb0 irq 3 vect 0x47 434xd* at xdc? drive ? 435 436## Xylogics 451 or 451 VME SMD disk controllers and disks, found 437## on sun4 systems. 438xyc0 at vme0 addr 0xee40 irq 3 vect 0x48 439xyc1 at vme0 addr 0xee48 irq 3 vect 0x49 440xy* at xyc? drive ? 441 442 443## Floppy controller and drive found on SPARCstations. 444 445fdc0 at mainbus0 # sun4c controller 446fdc0 at obio0 # sun4m controller 447fd* at fdc0 # the drive itself 448 449## PCMCIA IDE controllers 450#wdc* at pcmcia? 451#atabus* at ata? 452#wd* at atabus? drive ? flags 0x0000 453 454## PCMCIA wavelan card 455#wi* at pcmcia? function ? # Lucent WaveLan IEEE (802.11) 456 457## A disk-like interface to files. Can be used to create floppy, CD, 458## miniroot images, etc. 459 460pseudo-device vnd 4 461 462## Concatenated and striped disks; with this, you can create a software-based 463## disk array similar to a "RAID 0" setup. See ccd(4). 464 465pseudo-device ccd 4 466 467## Cryptographic disk devices; See cgd(4) 468 469#pseudo-device cgd 4 470 471## RAIDframe disk driver: software RAID driver. See raid(4). 472 473pseudo-device raid 8 474options RAID_AUTOCONFIG # auto-configuration of RAID components 475# Options to enable various other RAIDframe RAID types. 476# options RF_INCLUDE_EVENODD=1 477# options RF_INCLUDE_RAID5_RS=1 478# options RF_INCLUDE_PARITYLOGGING=1 479# options RF_INCLUDE_CHAINDECLUSTER=1 480# options RF_INCLUDE_INTERDECLUSTER=1 481# options RF_INCLUDE_PARITY_DECLUSTERING=1 482# options RF_INCLUDE_PARITY_DECLUSTERING_DS=1 483 484 485## Memory disk device, used on boot floppies with compressed 486## kernel-plus-root-disk images. 487 488#pseudo-device md 1 489 490 491#### Network interfaces 492 493## LANCE Ethernet - an AMD 7990 LANCE behind specialized DMA glue 494## Three flavors of additional SBus ethernets are available. One attaches 495## directly like the sun4c on-board, one uses the ledma device like the 496## sun4m on-board, and one uses the lebuffer device. 497 498le0 at obio0 addr 0xf9000000 level 6 # sun4/300 499le0 at sbus0 slot ? offset ? # sun4c on-board 500ledma0 at sbus0 slot ? offset ? # sun4m on-board 501le0 at ledma0 # sun4m on-board 502le* at sbus? slot ? offset ? # SBus 503ledma* at sbus? slot ? offset ? # SBus 504le* at ledma? # SBus 505lebuffer0 at sbus? slot ? offset ? # SBus 506le0 at lebuffer? # SBus 507lebuffer* at sbus? slot ? offset ? # SBus 508le* at lebuffer? # SBus 509 510 511## sun4/100 and sun4/200 Ethernet - an Intel 82586 on-board 512## or on a Multibus/VME card. 513ie0 at obio0 addr 0xf6000000 level 6 # sun4/200 on-board 514ie0 at obio0 addr 0x06000000 level 6 # sun4/100 on-board 515## VME: the first [addr,len] pair specifies the device registers; 516## the second pair specifies the on-board memory buffer 517ie1 at vme0 addr 0xe88000,0xe00000 len -1,0x40000 irq 3 vect 0x75 518ie2 at vme0 addr 0x31ff02,0x300000 len -1,0x40000 irq 3 vect 0x76 519ie3 at vme0 addr 0x35ff02,0x300000 len -1,0x40000 irq 3 vect 0x77 520ie4 at vme0 addr 0x2dff02,0x200000 len -1,0x40000 irq 3 vect 0x7c 521 522## Quad Ethernet Controller with BigMac (be, 10/100MBd) and Mace Ethernet 523## (qe, 10MBd) attached. 524qec* at sbus? slot ? offset ? # Quad Ethernet Controller 525be* at qec? # BigMac Ethernet (10/100MBd) 526qe* at qec? # Mace Ethernet (10MBd) 527 528## Happy Meal Ethernet 529hme* at sbus? slot ? offset ? 530 531# midway ATM 532en0 at sbus? slot ? offset ? 533 534# PCMCIA ethernet devices 535#ep* at pcmcia? 536#mbe* at pcmcia? 537#ne* at pcmcia? 538#sm* at pcmcia? 539 540# MII/PHY support 541exphy* at mii? phy ? # 3Com internal PHYs 542icsphy* at mii? phy ? # Integrated Circuit Systems ICS189x 543inphy* at mii? phy ? # Intel 82555 PHYs 544lxtphy* at mii? phy ? # Level One LXT-970 PHYs 545nsphy* at mii? phy ? # NS83840 PHYs 546qsphy* at mii? phy ? # Quality Semiconductor QS6612 PHYs 547sqphy* at mii? phy ? # Seeq 80220/80221/80223 PHYs 548tlphy* at mii? phy ? # ThunderLAN PHYs 549ukphy* at mii? phy ? # generic unknown PHYs 550 551## Loopback network interface; required 552pseudo-device loop 553 554## SLIP and CSLIP interfaces, for IP over a serial line. 555pseudo-device sl 2 556 557## PPP, the successor to SLIP. See pppd(8). 558pseudo-device ppp 2 559 560## PPP over Ethernet (RFC 2516) 561pseudo-device pppoe 562 563## Starmode Radio IP, a special hardware network device. 564#pseudo-device strip 1 565 566## Network "tunnel" device, allowing protocol stacks to run in the userland. 567## This is used by the third-party user-mode "ppp" program, and others. 568pseudo-device tun 4 569 570## Generic L3 over IP tunnel 571#pseudo-device gre 2 # generic L3 over IP tunnel 572 573## Berkeley Packet Filter, required to run RARPD. A generic C-language 574## interface that allows selective examining of incoming packets. 575pseudo-device bpfilter 8 576 577## IP Filter, used in firewall and NAT applications. See ipnat(8) for 578## one example of the use of the IP Filter. 579pseudo-device ipfilter 580 581## for IPv6 582pseudo-device gif 4 # IPv[46] over IPv[46] tunnel (RFC1933) 583#pseudo-device faith 1 # IPv[46] tcp relay translation i/f 584#pseudo-device stf 1 # 6to4 IPv6 over IPv4 encapsulation 585 586## IEEE 802.1Q Virtual LAN encapsulation, see vlan(4). 587pseudo-device vlan 588 589## Simple inter-network traffic bridging 590pseudo-device bridge 591#options BRIDGE_IPF # bridge uses IP/IPv6 pfil hooks too 592 593#### Audio and video devices 594 595## /dev/audio support (`audioamd' plus `audio') 596## 597audioamd0 at mainbus0 # sun4c 598audioamd0 at obio0 # sun4m 599audioamd0 at sbus0 slot ? offset ? # sun4m 600audio* at audioamd0 601 602audiocs0 at sbus0 slot ? offset ? # SUNW,CS4231 603audio* at audiocs0 604 605 606## Sun "bwtwo" black and white framebuffer, found on sun4, sun4c, and sun4m 607## systems. If your sun4 system has a cgfour installed in the P4 slot, 608## the P4 entries for "bwtwo" will attach to the overlay plane of the 609## "cgfour". 610 611bwtwo0 at sbus0 slot ? offset ? # sun4c and sun4m 612bwtwo* at sbus? slot ? offset ? # 613bwtwo0 at obio0 addr 0xfd000000 level 4 # sun4/200 614bwtwo0 at obio0 addr 0xfb300000 level 4 # sun4/300 in P4 slot 615bwtwo0 at obio0 addr 0x0b300000 level 4 # sun4/100 in P4 slot 616 617## Sun "cgtwo" VME color framebuffer 618cgtwo0 at vme0 addr 0x400000 irq ? vect 0xa8 619 620## Sun "cgthree" Sbus color framebuffer 621cgthree0 at sbus? slot ? offset ? 622cgthree* at sbus? slot ? offset ? 623#cgthree0 at obio? slot ? offset ? # sun4m 624 625## Sun "cgfour" color framebuffer with overlay plane. See above comment 626## regarding overlay plane. 627cgfour0 at obio0 addr 0xfb300000 level 4 # sun4/300 P4 628cgfour0 at obio0 addr 0x0b300000 level 4 # sun4/100 P4 629 630## Sun "cgsix" accelerated color framebuffer. 631cgsix0 at sbus? slot ? offset ? 632cgsix* at sbus? slot ? offset ? 633cgsix0 at obio0 addr 0xfb000000 level 4 # sun4/300 P4 634cgsix0 at obio0 addr 0x0b000000 level 4 # sun4/100 P4 635 636## Sun "cgeight" 24-bit framebuffer 637cgeight0 at obio0 addr 0xfb300000 level 4 # sun4/300 P4 638cgeight0 at obio0 addr 0x0b300000 level 4 # sun4/100 P4 639 640## Sun "tcx" accelerated color framebuffer. 641tcx0 at sbus? slot ? offset ? 642tcx* at sbus? slot ? offset ? 643 644# Sun "cgfourteen" accelerated 24-bit framebuffer. 645cgfourteen0 at obio0 # sun4m 646 647# P9100-based display on Tadpole SPARCbook 3. 648pnozz0 at sbus? slot ? offset ? 649 650# Sun ZX/Leo 24-bit framebuffer 651zx* at sbus? slot ? offset ? 652 653#### Other device configuration 654 655# Tadpole microcontroller 656tctrl0 at obio0 657 658## Pseudo ttys, required for network logins and programs like screen. 659 660pseudo-device pty # pseudo-terminals 661 662## Random device, used to implement /dev/random (a source of random noise), 663## and generate randomness for some kernel formulae. 664 665pseudo-device rnd 666 667# a pseudo device needed for Coda # also needs CODA (above) 668pseudo-device vcoda 4 # coda minicache <-> venus comm. 669 670pseudo-device clockctl # user control of clock subsystem 671pseudo-device ksyms # /dev/ksyms 672#pseudo-device pf # PF packet filter 673#pseudo-device pflog # PF log if 674