GENERIC revision 1.163
1# $NetBSD: GENERIC,v 1.163 2004/09/04 23:29:57 manu Exp $ 2# 3# GENERIC machine description file 4# 5# This machine description file is used to generate the default NetBSD 6# kernel. The generic kernel does not include all options, subsystems 7# and device drivers, but should be useful for most applications. 8# 9# The machine description file can be customised for your specific 10# machine to reduce the kernel size and improve its performance. 11# 12# For further information on compiling NetBSD kernels, see the config(8) 13# man page. 14# 15# For further information on hardware support for this architecture, see 16# the intro(4) man page. For further information about kernel options 17# for this architecture, see the options(4) man page. For an explanation 18# of each device driver in this file see the section 4 man page for the 19# device. 20 21include "arch/sparc/conf/std.sparc" 22 23options INCLUDE_CONFIG_FILE # embed config file in kernel binary 24 25#ident "GENERIC-$Revision: 1.163 $" 26 27maxusers 32 28 29## System kernel configuration. See options(4) for more detail. 30 31 32# Options for variants of the Sun SPARC architecure. 33# We currently support three architecture types; at least one is required. 34options SUN4 # sun4/100, sun4/200, sun4/300 35options SUN4C # sun4c - SS1, 1+, 2, ELC, SLC, IPC, IPX, etc. 36options SUN4M # sun4m - SS10, SS20, Classic, etc. 37options SUN4D # sun4d - SS1000, SC2000 38 39options SUN4_MMU3L # sun4/400 3-level MMU 40 41## System options specific to the sparc machine type 42 43# Blink the power LED on some machines to indicate the system load. 44#options BLINK 45 46## Use a faster console than the PROM's slow drawing routines. Not needed 47## for headless (no framebuffer) machines. 48options RASTERCONSOLE # fast rasterop console 49options FONT_GALLANT12x22 # the console font 50#options FONT_BOLD8x16 # a somewhat smaller font 51## default console colors: black-on-white; this can be changed 52## using the following two options. 53#options RASTERCONSOLE_FGCOL=WSCOL_BLACK 54#options RASTERCONSOLE_BGCOL=WSCOL_WHITE 55 56#### System options that are the same for all ports 57 58## Root device configuration: change the ?'s if you are going to use a 59## nonstandard root partition (other than where the kernel is booted from) 60## and/or nonstandard root type (not ffs or nfs). Normally this can be 61## automagically determined at boot time. 62 63config netbsd root on ? type ? 64 65## System call tracing (see ktrace(1)). 66options KTRACE 67options SYSTRACE # system call vetting via systrace(1) 68 69## Collect statistics on kernel malloc's and free's. This does have a 70## significant performance hit on slower machines, so it is intended for 71## diagnostic use only. 72#options KMEMSTATS 73 74## System V compatible IPC subsystem. (msgctl(2), semctl(2), and shmctl(2)) 75options SYSVMSG # System V message queues 76options SYSVSEM # System V semaphores 77#options SEMMNI=10 # number of semaphore identifiers 78#options SEMMNS=60 # number of semaphores in system 79#options SEMUME=10 # max number of undo entries per process 80#options SEMMNU=30 # number of undo structures in system 81options SYSVSHM # System V shared memory 82#options SHMMAXPGS=1024 # 1024 pages is the default 83options P1003_1B_SEMAPHORE # p1003.1b semaphore support 84 85## Loadable kernel module support; still under development. 86options LKM 87 88options USERCONF # userconf(4) support 89#options PIPE_SOCKETPAIR # smaller, but slower pipe(2) 90options SYSCTL_INCLUDE_DESCR # Include sysctl descriptions in kernel 91 92# Enable experimental buffer queue strategy for better responsiveness under 93# high disk I/O load. Use it with caution - it's not proven to be stable yet. 94#options NEW_BUFQ_STRATEGY 95 96## NFS boot options; tries DHCP/BOOTP then BOOTPARAM 97options NFS_BOOT_BOOTPARAM 98#options NFS_BOOT_BOOTP 99options NFS_BOOT_DHCP 100 101#### Debugging options 102 103## The DDB in-kernel debugger runs at panic (unless DDB_ONPANIC=0), or at 104## serial console break or keyboard reset, where the PROM would normally 105## intercept. DDB_HISTORY_SIZE adds up/down arrow command history. 106#options DDB # kernel dynamic debugger 107#options DDB_HISTORY_SIZE=100 # enable history editing in DDB 108#options DDB_ONPANIC=1 # see also sysctl(8): `ddb.onpanic' 109 110## You may also use gdb, on another computer connected to this machine over 111## a serial port. Both KGDB_DEV and KGDB_DEVRATE should be specified; 112## KGDB_DEV is a dev_t encoded device number of the serial port to use, where 113## the minor device number encodes the PROM enumeration of the serial ports, 114## i.e.: 115## 0xc00 = ttya, 0xc01 = ttyb, 0xc02 = ttyc, 0xc03 = ttyd. 116## (Note: ttyc and ttyd are available only on some sun4 models) 117#options KGDB # support for kernel gdb 118#options KGDB_DEV=0xc01 # kgdb device number (this is `ttyb') 119#options KGDB_DEVRATE=38400 # baud rate 120 121 122## Compile the kernel with debugging symbols (`netbsd.gdb' is the debug file), 123## such that gdb(1) can be used on a kernel coredump. 124 125#makeoptions DEBUG="-g" 126 127 128## Adds code to the kernel that does internal consistency checks, and will 129## cause the kernel to panic if corruption of internal data structures 130## is detected. 131#options DIAGNOSTIC # extra kernel sanity checking 132 133## Enable (possibly expensive) debugging code that may also display messages 134## on the system console 135#options DEBUG 136 137## Make SCSI error messages more verbose when explaining their meanings. 138options SCSIVERBOSE 139 140options MIIVERBOSE # verbose PHY autoconfig messages 141 142## `INSECURE' turns off the kernel security level (securelevel = 0 always). 143## This allows writing to /dev/mem, loading kernel modules while multi-user, 144## and other insecurities good only for development work. Do not use this 145## option on a production machine. 146#options INSECURE 147 148## `FDSCRIPTS' allows non-readable but executable scripts by providing a 149## pre-opened opaque file to the script interpreter. `SETUIDSCRIPTS', 150## which implies FDSCRIPTS, allows scripts to be set-user-id using the same 151## opaque file mechanism. Perl calls this "secure setuid scripts." 152 153#options FDSCRIPTS 154#options SETUIDSCRIPTS 155 156## Options for compatibility with previous releases foreign system binaries. 157## In the cases of COMPAT_SUNOS and COMPAT_SVR4, you may need to set up 158## additional user-level utilities or system configuration files. See 159## compat_sunos(8) and compat_svr4(8). 160 161options COMPAT_43 # 4.3BSD system interfaces 162options COMPAT_10 # NetBSD 1.0 binary compatibility 163options COMPAT_11 # NetBSD 1.1 binary compatibility 164options COMPAT_12 # NetBSD 1.2 binary compatibility 165options COMPAT_13 # NetBSD 1.3 binary compatibility 166options COMPAT_14 # NetBSD 1.4 binary compatibility 167options COMPAT_16 # NetBSD 1.6 binary compatibility 168options COMPAT_20 # NetBSD 2.0 binary compatibility 169options COMPAT_SUNOS # SunOS 4.x binary compatibility 170options COMPAT_SVR4 # SunOS 5.x binary compatibility 171 172## File systems. You probably need at least one of FFS or NFS. 173file-system FFS # Berkeley Fast Filesystem 174file-system NFS # Sun NFS-compatible filesystem client 175file-system KERNFS # kernel data-structure filesystem 176file-system NULLFS # NULL layered filesystem 177file-system OVERLAY # overlay file system 178file-system MFS # memory-based filesystem 179file-system FDESC # user file descriptor filesystem 180file-system UMAPFS # uid/gid remapping filesystem 181file-system LFS # Log-based filesystem (still experimental) 182file-system PORTAL # portal filesystem (still experimental) 183file-system PROCFS # /proc 184file-system CD9660 # ISO 9660 + Rock Ridge file system 185file-system UNION # union file system 186file-system MSDOSFS # MS-DOS FAT filesystem(s). 187file-system CODA # Coda File System; also needs vcoda (below) 188 189## File system options. 190options NFSSERVER # Sun NFS-compatible filesystem server 191options QUOTA # FFS quotas 192#options FFS_EI # FFS Endian Independent support 193options SOFTDEP # FFS soft updates support. 194 195## Network protocol support. In most environments, INET is required. 196options INET # IP (Internet Protocol) v4 197options INET6 # IPV6 198#options IPSEC # IP security 199#options IPSEC_ESP # IP security (encryption part; define w/IPSEC) 200#options IPSEC_DEBUG # debug for IP security 201#options GATEWAY # packet forwarding ("router switch") 202#options MROUTING # packet forwarding of multicast packets 203#options PIM # Protocol Independent Multicast 204#options DIRECTED_BROADCAST # allow broadcasts through routers 205options NS # Xerox NS networking 206#options NSIP # Xerox NS tunneling over IP 207options ISO,TPIP # OSI networking 208#options EON # OSI tunneling over IP 209#options CCITT,LLC,HDLC # X.25 packet switched protocol 210#options NETATALK # AppleTalk (over Ethernet) protocol 211options NTP # Network Time Protocol in-kernel support 212#options PPS_SYNC # Add serial line synchronization for NTP 213options PFIL_HOOKS # Add pfil(9) hooks, intended for custom LKMs. 214options IPFILTER_LOG # Add ipmon(8) logging for ipfilter device 215#options IPFILTER_DEFAULT_BLOCK # block all packets by default 216options PPP_BSDCOMP # Add BSD compression to ppp device 217options PPP_DEFLATE # Add deflate (libz) compression to ppp device 218options PPP_FILTER # Add active filters for ppp (via bpf) 219 220#options ALTQ # Manipulate network interfaces' output queues 221#options ALTQ_BLUE # Stochastic Fair Blue 222#options ALTQ_CBQ # Class-Based Queueing 223#options ALTQ_CDNR # Diffserv Traffic Conditioner 224#options ALTQ_FIFOQ # First-In First-Out Queue 225#options ALTQ_FLOWVALVE # RED/flow-valve (red-penalty-box) 226#options ALTQ_HFSC # Hierarchical Fair Service Curve 227#options ALTQ_LOCALQ # Local queueing discipline 228#options ALTQ_PRIQ # Priority Queueing 229#options ALTQ_RED # Random Early Detection 230#options ALTQ_RIO # RED with IN/OUT 231#options ALTQ_WFQ # Weighted Fair Queueing 232 233 234 235#### Main bus and CPU .. all systems. 236mainbus0 at root 237cpu0 at mainbus0 238cpuunit0 at mainbus0 # sun4d 239cpuunit* at mainbus0 # sun4d 240cpu0 at cpuunit0 # sun4d 241 242#### Bus types found on SPARC systems. 243 244sbus0 at mainbus0 # sun4c 245obio0 at mainbus0 # sun4 and sun4m 246sparcvme0 at mainbus0 # sun4 247iommu0 at mainbus0 # sun4m 248sbus0 at iommu0 # sun4m 249sparcvme0 at iommu0 # sun4m 250vme0 at sparcvme0 # MI VME attachment 251bootbus0 at cpuunit0 # sun4d 252bootbus* at cpuunit? # sun4d 253 254## SBus expander box 255xbox* at sbus? slot ? offset ? 256sbus* at xbox? 257 258## SBus to PCMCIA bridge 259nell* at sbus? slot ? offset ? # PCMCIA bridge 260pcmcia* at nell? 261 262#### Standard system devices -- all required for a given architecture 263 264## Auxiliary system registers on sun4c and sun4m 265auxreg0 at mainbus0 # sun4c 266auxreg0 at obio0 # sun4m 267auxiotwo0 at obio0 # only on Tadpole SPARCbook. 268 269## Power status and control register on Sun4m systems 270power0 at obio0 271 272## Mostek clock found on 4/300, sun4c, sun4m and sun4d systems. 273## The Mostek clock NVRAM is the "eeprom" on sun4/300 systems. 274clock0 at mainbus0 # sun4c 275clock0 at obio0 # sun4m 276clock0 at obio0 addr 0xf2000000 # sun4/300 277clock0 at bootbus0 # sun4d 278 279## Intersil clock found on 4/100 and 4/200 systems. 280oclock0 at obio0 addr 0xf3000000 # sun4/200 281oclock0 at obio0 addr 0x03000000 # sun4/100 282 283## Memory error registers. 284memreg0 at mainbus0 # sun4c 285memreg0 at obio0 # sun4m 286memreg0 at obio0 addr 0xf4000000 # sun4/200 and sun4/300 287memreg0 at obio0 addr 0x04000000 # sun4/100 288 289## ECC memory control 290eccmemctl0 at mainbus0 # sun4m 291 292## Timer chip found on 4/300, sun4c, and sun4m systems. 293timer0 at mainbus0 # sun4c 294timer0 at obio0 # sun4m 295timer0 at obio0 addr 0xef000000 # sun4/300 296 297## EEPROM found on 4/100 and 4/200 systems. Note that the 4/300 298## doesn't use this driver; the `EEPROM' is in the NVRAM on the 299## Mostek clock chip on 4/300 systems. 300eeprom0 at obio0 addr 0xf2000000 # sun4/200 301eeprom0 at obio0 addr 0x02000000 # sun4/100 302 303 304#### Serial port configuration 305 306## Zilog 8530 serial chips. Each has two-channels. 307## zs0 is ttya and ttyb. zs1 is the keyboard and mouse. 308zs0 at mainbus0 # sun4c 309zs0 at obio0 # sun4m 310zs0 at obio0 addr 0xf1000000 level 12 # sun4/200 and sun4/300 311zs0 at obio0 addr 0x01000000 level 12 # sun4/100 312zs0 at bootbus0 # sun4d 313zstty0 at zs0 channel 0 # ttya 314zstty1 at zs0 channel 1 # ttyb 315 316zs1 at mainbus0 # sun4c 317zs1 at obio0 # sun4m 318zs1 at obio0 addr 0xf0000000 level 12 # sun4/200 and sun4/300 319zs1 at obio0 addr 0x00000000 level 12 # sun4/100 320zs1 at bootbus0 # sun4d 321kbd0 at zs1 channel 0 # keyboard 322ms0 at zs1 channel 1 # mouse 323 324zs2 at obio0 addr 0xe0000000 level 12 # sun4/300 325zstty2 at zs2 channel 0 # ttyc 326zstty3 at zs2 channel 1 # ttyd 327 328zs* at bootbus? # sun4d 329zstty* at zs? 330 331## NS16x50 serial chips and clones. Present on the 332## Sun JavaStation-1 and Tadpole SPARCbook 3 333com* at obio0 # sun4m 334 335# Parallel port. 336bpp* at sbus? slot? offset ? 337 338## Magma Serial/Parallel driver 339magma* at sbus? slot ? offset ? 340mtty* at magma? 341mbpp* at magma? 342 343## SUNW,spif Serial/Parallel driver 344spif* at sbus? slot ? offset ? 345stty* at spif? 346sbpp* at spif? 347 348## PCMCIA serial interfaces 349#com* at pcmcia? 350#pcmcom* at pcmcia? 351#com* at pcmcom? 352 353#### Disk controllers and disks 354 355# 356 357## The following flags may be set for the NCR53c94 based esp driver: 358## bits 0-7: disable disconnect/reselect for the corresponding target 359## bits 8-15: disable synchronous negotiation for target [bit-8] 360 361## sun4/300, sun4c, sun4m on-board SCSI, and FSBE/S SBus SCSI cards. 362## Both `dma' and `esp' are needed in all cases. 363## Two kinds of additional SBus SCSI interfaces are available. One uses 364## "esp at sbus" like the sun4c on-board; the other uses "esp at dma". 365 366## sun4/300 SCSI - an NCR53c94 or equivalent behind 367## an LSI Logic DMA controller 368 369dma0 at obio0 addr 0xfa001000 level 4 # sun4/300 370esp0 at obio0 addr 0xfa000000 level 4 flags 0x0000 # sun4/300 371 372dma0 at sbus0 slot ? offset ? # sun4c/sun4m 373esp0 at sbus0 slot ? offset ? flags 0x0000 # sun4c 374esp0 at dma0 flags 0x0000 # sun4m 375 376# FSBE/S SCSI & SunSwift Sbus FAS366 377dma* at sbus? slot ? offset ? # SBus 378esp* at sbus? slot ? offset ? flags 0x0000 # SBus 379esp* at dma? flags 0x0000 # SBus 380 381scsibus* at esp? 382 383## Qlogic ISP SBus SCSI Card 384isp* at sbus? slot ? offset ? 385scsibus* at isp? 386 387## NCR5380-based "Sun SCSI 3" VME SCSI controller. 388## This driver has several flags which may be enabled by OR'ing 389## the values and using the "flags" directive. 390## Valid flags are: 391## 392## 0x01 Use DMA (may be polled) 393## 0x02 Use DMA completion interrupts 394## 0x04 Allow disconnect/reselect 395## 396## E.g. the following would enable DMA, interrupts, and reselect: 397## si0 at vme0 addr 0x200000 irq 3 vect 0x40 flags 0x07 398## 399## By default, DMA is enabled in the driver. 400 401si0 at vme0 addr 0x200000 irq 2 vect 0x40 402scsibus* at si? 403 404## NCR5380-based "SCSI Weird" on-board SCSI interface found 405## on sun4/100 systems. The flags are the same as the "si" 406## controller. Note, while DMA is enabled by default, only 407## polled DMA works at this time, and reselects do not work 408## on this particular controller. 409 410sw0 at obio0 addr 0x0a000000 level 3 411scsibus* at sw? 412 413## PCMCIA SCSI controllers 414#aic* at pcmcia? 415#scsibus* at aic? 416 417 418## These entries find devices on all SCSI busses and assign 419## unit numbers dynamically. 420sd* at scsibus? target ? lun ? # SCSI disks 421st* at scsibus? target ? lun ? # SCSI tapes 422cd* at scsibus? target ? lun ? # SCSI CD-ROMs 423ch* at scsibus? target ? lun ? # SCSI changer devices 424ss* at scsibus? target ? lun ? # SCSI scanners 425ses* at scsibus? target ? lun ? # SCSI SES/SAF-TE 426uk* at scsibus? target ? lun ? # unknown SCSI 427 428 429## Xylogics 753 or 7053 VME SMD disk controllers and disks, found 430## on sun4 systems. 431xdc0 at vme0 addr 0xee80 irq 3 vect 0x44 432xdc1 at vme0 addr 0xee90 irq 3 vect 0x45 433xdc2 at vme0 addr 0xeea0 irq 3 vect 0x46 434xdc3 at vme0 addr 0xeeb0 irq 3 vect 0x47 435xd* at xdc? drive ? 436 437## Xylogics 451 or 451 VME SMD disk controllers and disks, found 438## on sun4 systems. 439xyc0 at vme0 addr 0xee40 irq 3 vect 0x48 440xyc1 at vme0 addr 0xee48 irq 3 vect 0x49 441xy* at xyc? drive ? 442 443 444## Floppy controller and drive found on SPARCstations. 445 446fdc0 at mainbus0 # sun4c controller 447fdc0 at obio0 # sun4m controller 448fd* at fdc0 # the drive itself 449 450## PCMCIA IDE controllers 451#wdc* at pcmcia? 452#atabus* at ata? 453#wd* at atabus? drive ? flags 0x0000 454 455## PCMCIA wavelan card 456#wi* at pcmcia? function ? # Lucent WaveLan IEEE (802.11) 457 458## A disk-like interface to files. Can be used to create floppy, CD, 459## miniroot images, etc. 460 461pseudo-device vnd 4 462 463## Concatenated and striped disks; with this, you can create a software-based 464## disk array similar to a "RAID 0" setup. See ccd(4). 465 466pseudo-device ccd 4 467 468## Cryptographic disk devices; See cgd(4) 469 470#pseudo-device cgd 4 471 472## RAIDframe disk driver: software RAID driver. See raid(4). 473 474pseudo-device raid 8 475options RAID_AUTOCONFIG # auto-configuration of RAID components 476# Options to enable various other RAIDframe RAID types. 477# options RF_INCLUDE_EVENODD=1 478# options RF_INCLUDE_RAID5_RS=1 479# options RF_INCLUDE_PARITYLOGGING=1 480# options RF_INCLUDE_CHAINDECLUSTER=1 481# options RF_INCLUDE_INTERDECLUSTER=1 482# options RF_INCLUDE_PARITY_DECLUSTERING=1 483# options RF_INCLUDE_PARITY_DECLUSTERING_DS=1 484 485 486## Memory disk device, used on boot floppies with compressed 487## kernel-plus-root-disk images. 488 489#pseudo-device md 1 490 491 492#### Network interfaces 493 494## LANCE Ethernet - an AMD 7990 LANCE behind specialized DMA glue 495## Three flavors of additional SBus ethernets are available. One attaches 496## directly like the sun4c on-board, one uses the ledma device like the 497## sun4m on-board, and one uses the lebuffer device. 498 499le0 at obio0 addr 0xf9000000 level 6 # sun4/300 500le0 at sbus0 slot ? offset ? # sun4c on-board 501ledma0 at sbus0 slot ? offset ? # sun4m on-board 502le0 at ledma0 # sun4m on-board 503le* at sbus? slot ? offset ? # SBus 504ledma* at sbus? slot ? offset ? # SBus 505le* at ledma? # SBus 506lebuffer0 at sbus? slot ? offset ? # SBus 507le0 at lebuffer? # SBus 508lebuffer* at sbus? slot ? offset ? # SBus 509le* at lebuffer? # SBus 510 511 512## sun4/100 and sun4/200 Ethernet - an Intel 82586 on-board 513## or on a Multibus/VME card. 514ie0 at obio0 addr 0xf6000000 level 6 # sun4/200 on-board 515ie0 at obio0 addr 0x06000000 level 6 # sun4/100 on-board 516## VME: the first [addr,len] pair specifies the device registers; 517## the second pair specifies the on-board memory buffer 518ie1 at vme0 addr 0xe88000,0xe00000 len -1,0x40000 irq 3 vect 0x75 519ie2 at vme0 addr 0x31ff02,0x300000 len -1,0x40000 irq 3 vect 0x76 520ie3 at vme0 addr 0x35ff02,0x300000 len -1,0x40000 irq 3 vect 0x77 521ie4 at vme0 addr 0x2dff02,0x200000 len -1,0x40000 irq 3 vect 0x7c 522 523## Quad Ethernet Controller with BigMac (be, 10/100MBd) and Mace Ethernet 524## (qe, 10MBd) attached. 525qec* at sbus? slot ? offset ? # Quad Ethernet Controller 526be* at qec? # BigMac Ethernet (10/100MBd) 527qe* at qec? # Mace Ethernet (10MBd) 528 529## Happy Meal Ethernet 530hme* at sbus? slot ? offset ? 531 532# midway ATM 533en0 at sbus? slot ? offset ? 534 535# PCMCIA ethernet devices 536#ep* at pcmcia? 537#mbe* at pcmcia? 538#ne* at pcmcia? 539#sm* at pcmcia? 540 541# MII/PHY support 542exphy* at mii? phy ? # 3Com internal PHYs 543icsphy* at mii? phy ? # Integrated Circuit Systems ICS189x 544inphy* at mii? phy ? # Intel 82555 PHYs 545lxtphy* at mii? phy ? # Level One LXT-970 PHYs 546nsphy* at mii? phy ? # NS83840 PHYs 547qsphy* at mii? phy ? # Quality Semiconductor QS6612 PHYs 548sqphy* at mii? phy ? # Seeq 80220/80221/80223 PHYs 549tlphy* at mii? phy ? # ThunderLAN PHYs 550ukphy* at mii? phy ? # generic unknown PHYs 551 552## Loopback network interface; required 553pseudo-device loop 554 555## SLIP and CSLIP interfaces, for IP over a serial line. 556pseudo-device sl 2 557 558## PPP, the successor to SLIP. See pppd(8). 559pseudo-device ppp 2 560 561## PPP over Ethernet (RFC 2516) 562pseudo-device pppoe 563 564## Starmode Radio IP, a special hardware network device. 565#pseudo-device strip 1 566 567## Network "tunnel" device, allowing protocol stacks to run in the userland. 568## This is used by the third-party user-mode "ppp" program, and others. 569pseudo-device tun 4 570 571## Generic L3 over IP tunnel 572#pseudo-device gre 2 # generic L3 over IP tunnel 573 574## Berkeley Packet Filter, required to run RARPD. A generic C-language 575## interface that allows selective examining of incoming packets. 576pseudo-device bpfilter 8 577 578## IP Filter, used in firewall and NAT applications. See ipnat(8) for 579## one example of the use of the IP Filter. 580pseudo-device ipfilter 581 582## for IPv6 583pseudo-device gif 4 # IPv[46] over IPv[46] tunnel (RFC1933) 584#pseudo-device faith 1 # IPv[46] tcp relay translation i/f 585#pseudo-device stf 1 # 6to4 IPv6 over IPv4 encapsulation 586 587## IEEE 802.1Q Virtual LAN encapsulation, see vlan(4). 588pseudo-device vlan 589 590## Simple inter-network traffic bridging 591pseudo-device bridge 592#options BRIDGE_IPF # bridge uses IP/IPv6 pfil hooks too 593 594#### Audio and video devices 595 596## /dev/audio support (`audioamd' plus `audio') 597## 598audioamd0 at mainbus0 # sun4c 599audioamd0 at obio0 # sun4m 600audioamd0 at sbus0 slot ? offset ? # sun4m 601audio* at audioamd0 602 603audiocs0 at sbus0 slot ? offset ? # SUNW,CS4231 604audio* at audiocs0 605 606 607## Sun "bwtwo" black and white framebuffer, found on sun4, sun4c, and sun4m 608## systems. If your sun4 system has a cgfour installed in the P4 slot, 609## the P4 entries for "bwtwo" will attach to the overlay plane of the 610## "cgfour". 611 612bwtwo0 at sbus0 slot ? offset ? # sun4c and sun4m 613bwtwo* at sbus? slot ? offset ? # 614bwtwo0 at obio0 addr 0xfd000000 level 4 # sun4/200 615bwtwo0 at obio0 addr 0xfb300000 level 4 # sun4/300 in P4 slot 616bwtwo0 at obio0 addr 0x0b300000 level 4 # sun4/100 in P4 slot 617 618## Sun "cgtwo" VME color framebuffer 619cgtwo0 at vme0 addr 0x400000 irq ? vect 0xa8 620 621## Sun "cgthree" Sbus color framebuffer 622cgthree0 at sbus? slot ? offset ? 623cgthree* at sbus? slot ? offset ? 624#cgthree0 at obio? slot ? offset ? # sun4m 625 626## Sun "cgfour" color framebuffer with overlay plane. See above comment 627## regarding overlay plane. 628cgfour0 at obio0 addr 0xfb300000 level 4 # sun4/300 P4 629cgfour0 at obio0 addr 0x0b300000 level 4 # sun4/100 P4 630 631## Sun "cgsix" accelerated color framebuffer. 632cgsix0 at sbus? slot ? offset ? 633cgsix* at sbus? slot ? offset ? 634cgsix0 at obio0 addr 0xfb000000 level 4 # sun4/300 P4 635cgsix0 at obio0 addr 0x0b000000 level 4 # sun4/100 P4 636 637## Sun "cgeight" 24-bit framebuffer 638cgeight0 at obio0 addr 0xfb300000 level 4 # sun4/300 P4 639cgeight0 at obio0 addr 0x0b300000 level 4 # sun4/100 P4 640 641## Sun "tcx" accelerated color framebuffer. 642tcx0 at sbus? slot ? offset ? 643tcx* at sbus? slot ? offset ? 644 645# Sun "cgfourteen" accelerated 24-bit framebuffer. 646cgfourteen0 at obio0 # sun4m 647 648# P9100-based display on Tadpole SPARCbook 3. 649pnozz0 at sbus? slot ? offset ? 650 651# Sun ZX/Leo 24-bit framebuffer 652zx* at sbus? slot ? offset ? 653 654#### Other device configuration 655 656# Tadpole microcontroller 657tctrl0 at obio0 658 659## Pseudo ttys, required for network logins and programs like screen. 660 661pseudo-device pty # pseudo-terminals 662 663## Random device, used to implement /dev/random (a source of random noise), 664## and generate randomness for some kernel formulae. 665 666pseudo-device rnd 667 668# a pseudo device needed for Coda # also needs CODA (above) 669pseudo-device vcoda 4 # coda minicache <-> venus comm. 670 671pseudo-device clockctl # user control of clock subsystem 672pseudo-device ksyms # /dev/ksyms 673#pseudo-device pf # PF packet filter 674#pseudo-device pflog # PF log if 675