GENERIC revision 1.190
1 # $NetBSD: GENERIC,v 1.190 2006/08/12 15:29:54 christos Exp $ 2 # 3 # GENERIC machine description file 4 # 5 # This machine description file is used to generate the default NetBSD 6 # kernel. The generic kernel does not include all options, subsystems 7 # and device drivers, but should be useful for most applications. 8 # 9 # The machine description file can be customised for your specific 10 # machine to reduce the kernel size and improve its performance. 11 # 12 # For further information on compiling NetBSD kernels, see the config(8) 13 # man page. 14 # 15 # For further information on hardware support for this architecture, see 16 # the intro(4) man page. For further information about kernel options 17 # for this architecture, see the options(4) man page. For an explanation 18 # of each device driver in this file see the section 4 man page for the 19 # device. 20 21 include "arch/sparc/conf/std.sparc" 22 23 options INCLUDE_CONFIG_FILE # embed config file in kernel binary 24 25 #ident "GENERIC-$Revision: 1.190 $" 26 27 maxusers 32 28 29 ## System kernel configuration. See options(4) for more detail. 30 31 32 # Options for variants of the Sun SPARC architecure. 33 # We currently support three architecture types; at least one is required. 34 options SUN4 # sun4/100, sun4/200, sun4/300 35 options SUN4C # sun4c - SS1, 1+, 2, ELC, SLC, IPC, IPX, etc. 36 options SUN4M # sun4m - SS10, SS20, Classic, etc. 37 options SUN4D # sun4d - SS1000, SC2000 38 39 options SUN4_MMU3L # sun4/400 3-level MMU 40 41 ## System options specific to the sparc machine type 42 43 # Blink the power LED on some machines to indicate the system load. 44 #options BLINK 45 46 ## Use a faster console than the PROM's slow drawing routines. Not needed 47 ## for headless (no framebuffer) machines. 48 options RASTERCONSOLE # fast rasterop console 49 options FONT_GALLANT12x22 # the console font 50 #options FONT_BOLD8x16 # a somewhat smaller font 51 ## default console colors: black-on-white; this can be changed 52 ## using the following two options. 53 #options RASTERCONSOLE_FGCOL=WSCOL_BLACK 54 #options RASTERCONSOLE_BGCOL=WSCOL_WHITE 55 56 #### System options that are the same for all ports 57 58 ## Root device configuration: change the ?'s if you are going to use a 59 ## nonstandard root partition (other than where the kernel is booted from) 60 ## and/or nonstandard root type (not ffs or nfs). Normally this can be 61 ## automagically determined at boot time. 62 63 config netbsd root on ? type ? 64 65 ## System call tracing (see ktrace(1)). 66 options KTRACE 67 #options SYSTRACE # system call vetting via systrace(1) 68 69 ## Collect statistics on kernel malloc's and free's. This does have a 70 ## significant performance hit on slower machines, so it is intended for 71 ## diagnostic use only. 72 #options KMEMSTATS 73 74 ## System V compatible IPC subsystem. (msgctl(2), semctl(2), and shmctl(2)) 75 options SYSVMSG # System V message queues 76 options SYSVSEM # System V semaphores 77 #options SEMMNI=10 # number of semaphore identifiers 78 #options SEMMNS=60 # number of semaphores in system 79 #options SEMUME=10 # max number of undo entries per process 80 #options SEMMNU=30 # number of undo structures in system 81 options SYSVSHM # System V shared memory 82 #options SHMMAXPGS=1024 # 1024 pages is the default 83 options P1003_1B_SEMAPHORE # p1003.1b semaphore support 84 85 ## Loadable kernel module support; still under development. 86 options LKM 87 88 options USERCONF # userconf(4) support 89 #options PIPE_SOCKETPAIR # smaller, but slower pipe(2) 90 options SYSCTL_INCLUDE_DESCR # Include sysctl descriptions in kernel 91 92 # Enable experimental buffer queue strategy for better responsiveness under 93 # high disk I/O load. Use it with caution - it's not proven to be stable yet. 94 #options BUFQ_READPRIO 95 #options BUFQ_PRIOCSCAN 96 97 ## NFS boot options; tries DHCP/BOOTP then BOOTPARAM 98 options NFS_BOOT_BOOTPARAM 99 #options NFS_BOOT_BOOTP 100 options NFS_BOOT_DHCP 101 102 #### Debugging options 103 104 ## The DDB in-kernel debugger runs at panic (unless DDB_ONPANIC=0), or at 105 ## serial console break or keyboard reset, where the PROM would normally 106 ## intercept. DDB_HISTORY_SIZE adds up/down arrow command history. 107 #options DDB # kernel dynamic debugger 108 #options DDB_HISTORY_SIZE=100 # enable history editing in DDB 109 #options DDB_ONPANIC=1 # see also sysctl(8): `ddb.onpanic' 110 111 ## You may also use gdb, on another computer connected to this machine over 112 ## a serial port. Both KGDB_DEV and KGDB_DEVRATE should be specified; 113 ## KGDB_DEV is a dev_t encoded device number of the serial port to use, where 114 ## the minor device number encodes the PROM enumeration of the serial ports, 115 ## i.e.: 116 ## 0xc00 = ttya, 0xc01 = ttyb, 0xc02 = ttyc, 0xc03 = ttyd. 117 ## (Note: ttyc and ttyd are available only on some sun4 models) 118 #options KGDB # support for kernel gdb 119 #options KGDB_DEV=0xc01 # kgdb device number (this is `ttyb') 120 #options KGDB_DEVRATE=38400 # baud rate 121 122 123 ## Compile the kernel with debugging symbols (`netbsd.gdb' is the debug file), 124 ## such that gdb(1) can be used on a kernel coredump. 125 126 #makeoptions DEBUG="-g" 127 128 129 ## Adds code to the kernel that does internal consistency checks, and will 130 ## cause the kernel to panic if corruption of internal data structures 131 ## is detected. 132 #options DIAGNOSTIC # extra kernel sanity checking 133 134 ## Enable (possibly expensive) debugging code that may also display messages 135 ## on the system console 136 #options DEBUG 137 138 ## Make SCSI error messages more verbose when explaining their meanings. 139 options SCSIVERBOSE 140 141 options MIIVERBOSE # verbose PHY autoconfig messages 142 143 ## `INSECURE' turns off the kernel security level (securelevel = 0 always). 144 ## This allows writing to /dev/mem, loading kernel modules while multi-user, 145 ## and other insecurities good only for development work. Do not use this 146 ## option on a production machine. 147 #options INSECURE 148 149 ## `FDSCRIPTS' allows non-readable but executable scripts by providing a 150 ## pre-opened opaque file to the script interpreter. `SETUIDSCRIPTS', 151 ## which implies FDSCRIPTS, allows scripts to be set-user-id using the same 152 ## opaque file mechanism. Perl calls this "secure setuid scripts." 153 154 #options FDSCRIPTS 155 #options SETUIDSCRIPTS 156 157 ## Options for compatibility with previous releases foreign system binaries. 158 ## In the cases of COMPAT_SUNOS and COMPAT_SVR4, you may need to set up 159 ## additional user-level utilities or system configuration files. See 160 ## compat_sunos(8) and compat_svr4(8). 161 162 options COMPAT_43 # 4.3BSD system interfaces 163 options COMPAT_10 # NetBSD 1.0 binary compatibility 164 options COMPAT_11 # NetBSD 1.1 binary compatibility 165 options COMPAT_12 # NetBSD 1.2 binary compatibility 166 options COMPAT_13 # NetBSD 1.3 binary compatibility 167 options COMPAT_14 # NetBSD 1.4 binary compatibility 168 options COMPAT_16 # NetBSD 1.6 binary compatibility 169 options COMPAT_20 # NetBSD 2.0 binary compatibility 170 options COMPAT_30 # NetBSD 3.0 compatibility. 171 options COMPAT_SUNOS # SunOS 4.x binary compatibility 172 options COMPAT_SVR4 # SunOS 5.x binary compatibility 173 options COMPAT_BSDPTY # /dev/[pt]ty?? ptys. 174 175 ## File systems. You probably need at least one of FFS or NFS. 176 file-system FFS # Berkeley Fast Filesystem 177 file-system NFS # Sun NFS-compatible filesystem client 178 file-system KERNFS # kernel data-structure filesystem 179 file-system NULLFS # NULL layered filesystem 180 file-system OVERLAY # overlay file system 181 file-system MFS # memory-based filesystem 182 file-system FDESC # user file descriptor filesystem 183 file-system UMAPFS # uid/gid remapping filesystem 184 file-system LFS # Log-based filesystem (still experimental) 185 file-system PORTAL # portal filesystem (still experimental) 186 file-system PROCFS # /proc 187 file-system CD9660 # ISO 9660 + Rock Ridge file system 188 file-system UNION # union file system 189 file-system MSDOSFS # MS-DOS FAT filesystem(s). 190 file-system CODA # Coda File System; also needs vcoda (below) 191 file-system PTYFS # /dev/pts/N support 192 #file-system TMPFS # experimental - Efficient memory file-system 193 #file-system UDF # experimental - OSTA UDF CD/DVD file-system 194 195 ## File system options. 196 options NFSSERVER # Sun NFS-compatible filesystem server 197 options QUOTA # FFS quotas 198 #options FFS_EI # FFS Endian Independent support 199 options SOFTDEP # FFS soft updates support. 200 #options UFS_DIRHASH # UFS Large Directory Hashing - Experimental 201 #options FFS_NO_SNAPSHOT # No FFS snapshot support 202 203 ## Network protocol support. In most environments, INET is required. 204 options INET # IP (Internet Protocol) v4 205 options INET6 # IPV6 206 #options IPSEC # IP security 207 #options IPSEC_ESP # IP security (encryption part; define w/IPSEC) 208 #options IPSEC_NAT_T # IPsec NAT traversal (NAT-T) 209 #options IPSEC_DEBUG # debug for IP security 210 #options GATEWAY # packet forwarding ("router switch") 211 #options MROUTING # packet forwarding of multicast packets 212 #options PIM # Protocol Independent Multicast 213 #options DIRECTED_BROADCAST # allow broadcasts through routers 214 options NS # Xerox NS networking 215 #options NSIP # Xerox NS tunneling over IP 216 options ISO,TPIP # OSI networking 217 #options EON # OSI tunneling over IP 218 #options CCITT,LLC,HDLC # X.25 packet switched protocol 219 #options NETATALK # AppleTalk (over Ethernet) protocol 220 options NTP # Network Time Protocol in-kernel support 221 #options PPS_SYNC # Add serial line synchronization for NTP 222 options PFIL_HOOKS # Add pfil(9) hooks, intended for custom LKMs. 223 options IPFILTER_LOG # Add ipmon(8) logging for ipfilter device 224 #options IPFILTER_DEFAULT_BLOCK # block all packets by default 225 options PPP_BSDCOMP # Add BSD compression to ppp device 226 options PPP_DEFLATE # Add deflate (libz) compression to ppp device 227 options PPP_FILTER # Add active filters for ppp (via bpf) 228 229 #options ALTQ # Manipulate network interfaces' output queues 230 #options ALTQ_BLUE # Stochastic Fair Blue 231 #options ALTQ_CBQ # Class-Based Queueing 232 #options ALTQ_CDNR # Diffserv Traffic Conditioner 233 #options ALTQ_FIFOQ # First-In First-Out Queue 234 #options ALTQ_FLOWVALVE # RED/flow-valve (red-penalty-box) 235 #options ALTQ_HFSC # Hierarchical Fair Service Curve 236 #options ALTQ_LOCALQ # Local queueing discipline 237 #options ALTQ_PRIQ # Priority Queueing 238 #options ALTQ_RED # Random Early Detection 239 #options ALTQ_RIO # RED with IN/OUT 240 #options ALTQ_WFQ # Weighted Fair Queueing 241 242 243 244 #### Main bus and CPU .. all systems. 245 mainbus0 at root 246 cpu0 at mainbus0 247 cpuunit0 at mainbus0 # sun4d 248 cpuunit* at mainbus0 # sun4d 249 cpu0 at cpuunit0 # sun4d 250 251 #### Bus types found on SPARC systems. 252 253 sbus0 at mainbus0 # sun4c 254 obio0 at mainbus0 # sun4 and sun4m 255 sparcvme0 at mainbus0 # sun4 256 iommu0 at mainbus0 # sun4m 257 sbus0 at iommu0 # sun4m 258 sparcvme0 at iommu0 # sun4m 259 vme0 at sparcvme0 # MI VME attachment 260 bootbus0 at cpuunit0 # sun4d 261 bootbus* at cpuunit? # sun4d 262 263 ## SBus expander box 264 xbox* at sbus? slot ? offset ? 265 sbus* at xbox? 266 267 ## SBus to PCMCIA bridge 268 nell* at sbus? slot ? offset ? # PCMCIA bridge 269 pcmcia* at nell? 270 tslot* at sbus? slot ? offset ? # PCMCIA bridge (tadpole 3gx) 271 pcmcia* at tslot? 272 273 #### Standard system devices -- all required for a given architecture 274 275 ## Auxiliary system registers on sun4c and sun4m 276 auxreg0 at mainbus0 # sun4c 277 auxreg0 at obio0 # sun4m 278 auxiotwo0 at obio0 # only on Tadpole SPARCbook. 279 280 ## Power status and control register on Sun4m systems 281 power0 at obio0 282 283 ## Mostek clock found on 4/300, sun4c, sun4m and sun4d systems. 284 ## The Mostek clock NVRAM is the "eeprom" on sun4/300 systems. 285 clock0 at mainbus0 # sun4c 286 clock0 at obio0 # sun4m 287 clock0 at obio0 addr 0xf2000000 # sun4/300 288 clock0 at bootbus0 # sun4d 289 290 ## Intersil clock found on 4/100 and 4/200 systems. 291 oclock0 at obio0 addr 0xf3000000 # sun4/200 292 oclock0 at obio0 addr 0x03000000 # sun4/100 293 294 ## Memory error registers. 295 memreg0 at mainbus0 # sun4c 296 memreg0 at obio0 # sun4m 297 memreg0 at obio0 addr 0xf4000000 # sun4/200 and sun4/300 298 memreg0 at obio0 addr 0x04000000 # sun4/100 299 300 ## ECC memory control 301 eccmemctl0 at mainbus0 # sun4m 302 303 ## Timer chip found on 4/300, sun4c, and sun4m systems. 304 timer0 at mainbus0 # sun4c 305 timer0 at obio0 # sun4m 306 timer0 at obio0 addr 0xef000000 # sun4/300 307 308 ## EEPROM found on 4/100 and 4/200 systems. Note that the 4/300 309 ## doesn't use this driver; the `EEPROM' is in the NVRAM on the 310 ## Mostek clock chip on 4/300 systems. 311 eeprom0 at obio0 addr 0xf2000000 # sun4/200 312 eeprom0 at obio0 addr 0x02000000 # sun4/100 313 314 315 #### Serial port configuration 316 317 ## Zilog 8530 serial chips. Each has two-channels. 318 ## zs0 is ttya and ttyb. zs1 is the keyboard and mouse. 319 zs0 at mainbus0 # sun4c 320 zs0 at obio0 # sun4m 321 zs0 at obio0 addr 0xf1000000 level 12 # sun4/200 and sun4/300 322 zs0 at obio0 addr 0x01000000 level 12 # sun4/100 323 zs0 at bootbus0 # sun4d 324 zstty0 at zs0 channel 0 # ttya 325 zstty1 at zs0 channel 1 # ttyb 326 327 zs1 at mainbus0 # sun4c 328 zs1 at obio0 # sun4m 329 zs1 at obio0 addr 0xf0000000 level 12 # sun4/200 and sun4/300 330 zs1 at obio0 addr 0x00000000 level 12 # sun4/100 331 zs1 at bootbus0 # sun4d 332 kbd0 at zs1 channel 0 # keyboard 333 ms0 at zs1 channel 1 # mouse 334 335 zs2 at obio0 addr 0xe0000000 level 12 # sun4/300 336 zstty2 at zs2 channel 0 # ttyc 337 zstty3 at zs2 channel 1 # ttyd 338 339 zs* at bootbus? # sun4d 340 zstty* at zs? 341 342 ## NS16x50 serial chips and clones. Present on the 343 ## Sun JavaStation-1 and Tadpole SPARCbook 3 344 com* at obio0 # sun4m 345 346 # Parallel port. 347 bpp* at sbus? slot? offset ? 348 349 ## Magma Serial/Parallel driver 350 magma* at sbus? slot ? offset ? 351 mtty* at magma? 352 mbpp* at magma? 353 354 ## SUNW,spif Serial/Parallel driver 355 spif* at sbus? slot ? offset ? 356 stty* at spif? 357 sbpp* at spif? 358 359 ## PCMCIA serial interfaces 360 #com* at pcmcia? 361 #pcmcom* at pcmcia? 362 #com* at pcmcom? 363 364 #### Disk controllers and disks 365 366 # 367 368 ## The following flags may be set for the NCR53c94 based esp driver: 369 ## bits 0-7: disable disconnect/reselect for the corresponding target 370 ## bits 8-15: disable synchronous negotiation for target [bit-8] 371 372 ## sun4/300, sun4c, sun4m on-board SCSI, and FSBE/S SBus SCSI cards. 373 ## Both `dma' and `esp' are needed in all cases. 374 ## Two kinds of additional SBus SCSI interfaces are available. One uses 375 ## "esp at sbus" like the sun4c on-board; the other uses "esp at dma". 376 377 ## sun4/300 SCSI - an NCR53c94 or equivalent behind 378 ## an LSI Logic DMA controller 379 380 dma0 at obio0 addr 0xfa001000 level 4 # sun4/300 381 esp0 at obio0 addr 0xfa000000 level 4 flags 0x0000 # sun4/300 382 383 dma0 at sbus0 slot ? offset ? # sun4c/sun4m 384 esp0 at sbus0 slot ? offset ? flags 0x0000 # sun4c 385 esp0 at dma0 flags 0x0000 # sun4m 386 387 # FSBE/S SCSI & SunSwift Sbus FAS366 388 dma* at sbus? slot ? offset ? # SBus 389 esp* at sbus? slot ? offset ? flags 0x0000 # SBus 390 esp* at dma? flags 0x0000 # SBus 391 392 scsibus* at esp? 393 394 ## Qlogic ISP SBus SCSI Card 395 isp* at sbus? slot ? offset ? 396 scsibus* at isp? 397 398 ## NCR5380-based "Sun SCSI 3" VME SCSI controller. 399 ## This driver has several flags which may be enabled by OR'ing 400 ## the values and using the "flags" directive. 401 ## Valid flags are: 402 ## 403 ## 0x01 Use DMA (may be polled) 404 ## 0x02 Use DMA completion interrupts 405 ## 0x04 Allow disconnect/reselect 406 ## 407 ## E.g. the following would enable DMA, interrupts, and reselect: 408 ## si0 at vme0 addr 0x200000 irq 3 vect 0x40 flags 0x07 409 ## 410 ## By default, DMA is enabled in the driver. 411 412 si0 at vme0 addr 0x200000 irq 2 vect 0x40 413 scsibus* at si? 414 415 ## NCR5380-based "SCSI Weird" on-board SCSI interface found 416 ## on sun4/100 systems. The flags are the same as the "si" 417 ## controller. Note, while DMA is enabled by default, only 418 ## polled DMA works at this time, and reselects do not work 419 ## on this particular controller. 420 421 sw0 at obio0 addr 0x0a000000 level 3 422 scsibus* at sw? 423 424 ## PCMCIA SCSI controllers 425 #aic* at pcmcia? 426 #spc* at pcmcia? 427 #scsibus* at aic? 428 #scsibus* at spc? 429 430 431 ## These entries find devices on all SCSI busses and assign 432 ## unit numbers dynamically. 433 sd* at scsibus? target ? lun ? # SCSI disks 434 st* at scsibus? target ? lun ? # SCSI tapes 435 cd* at scsibus? target ? lun ? # SCSI CD-ROMs 436 ch* at scsibus? target ? lun ? # SCSI changer devices 437 ss* at scsibus? target ? lun ? # SCSI scanners 438 ses* at scsibus? target ? lun ? # SCSI SES/SAF-TE 439 uk* at scsibus? target ? lun ? # unknown SCSI 440 441 442 ## Xylogics 753 or 7053 VME SMD disk controllers and disks, found 443 ## on sun4 systems. 444 xdc0 at vme0 addr 0xee80 irq 3 vect 0x44 445 xdc1 at vme0 addr 0xee90 irq 3 vect 0x45 446 xdc2 at vme0 addr 0xeea0 irq 3 vect 0x46 447 xdc3 at vme0 addr 0xeeb0 irq 3 vect 0x47 448 xd* at xdc? drive ? 449 450 ## Xylogics 451 or 451 VME SMD disk controllers and disks, found 451 ## on sun4 systems. 452 xyc0 at vme0 addr 0xee40 irq 3 vect 0x48 453 xyc1 at vme0 addr 0xee48 irq 3 vect 0x49 454 xy* at xyc? drive ? 455 456 457 ## Floppy controller and drive found on SPARCstations. 458 459 fdc0 at mainbus0 # sun4c controller 460 fdc0 at obio0 # sun4m controller 461 fd* at fdc0 # the drive itself 462 463 ## PCMCIA IDE controllers 464 #wdc* at pcmcia? 465 #atabus* at ata? 466 #wd* at atabus? drive ? flags 0x0000 467 468 ## PCMCIA wavelan card 469 #wi* at pcmcia? function ? # Lucent WaveLan IEEE (802.11) 470 471 ## A disk-like interface to files. Can be used to create floppy, CD, 472 ## miniroot images, etc. 473 474 pseudo-device vnd 475 #options VND_COMPRESSION # compressed vnd(4) 476 477 ## Concatenated and striped disks; with this, you can create a software-based 478 ## disk array similar to a "RAID 0" setup. See ccd(4). 479 480 pseudo-device ccd 4 481 482 ## Cryptographic disk devices; See cgd(4) 483 484 #pseudo-device cgd 4 485 486 ## RAIDframe disk driver: software RAID driver. See raid(4). 487 488 pseudo-device raid 8 489 options RAID_AUTOCONFIG # auto-configuration of RAID components 490 # Options to enable various other RAIDframe RAID types. 491 # options RF_INCLUDE_EVENODD=1 492 # options RF_INCLUDE_RAID5_RS=1 493 # options RF_INCLUDE_PARITYLOGGING=1 494 # options RF_INCLUDE_CHAINDECLUSTER=1 495 # options RF_INCLUDE_INTERDECLUSTER=1 496 # options RF_INCLUDE_PARITY_DECLUSTERING=1 497 # options RF_INCLUDE_PARITY_DECLUSTERING_DS=1 498 499 500 ## Memory disk device, used on boot floppies with compressed 501 ## kernel-plus-root-disk images. 502 503 #pseudo-device md 1 504 505 506 #### Network interfaces 507 508 ## LANCE Ethernet - an AMD 7990 LANCE behind specialized DMA glue 509 ## Three flavors of additional SBus ethernets are available. One attaches 510 ## directly like the sun4c on-board, one uses the ledma device like the 511 ## sun4m on-board, and one uses the lebuffer device. 512 513 le0 at obio0 addr 0xf9000000 level 6 # sun4/300 514 le0 at sbus0 slot ? offset ? # sun4c on-board 515 ledma0 at sbus0 slot ? offset ? # sun4m on-board 516 le0 at ledma0 # sun4m on-board 517 le* at sbus? slot ? offset ? # SBus 518 ledma* at sbus? slot ? offset ? # SBus 519 le* at ledma? # SBus 520 lebuffer0 at sbus? slot ? offset ? # SBus 521 le0 at lebuffer? # SBus 522 lebuffer* at sbus? slot ? offset ? # SBus 523 le* at lebuffer? # SBus 524 525 526 ## sun4/100 and sun4/200 Ethernet - an Intel 82586 on-board 527 ## or on a Multibus/VME card. 528 ie0 at obio0 addr 0xf6000000 level 6 # sun4/200 on-board 529 ie0 at obio0 addr 0x06000000 level 6 # sun4/100 on-board 530 ## VME: the first [addr,len] pair specifies the device registers; 531 ## the second pair specifies the on-board memory buffer 532 ie1 at vme0 addr 0xe88000,0xe00000 len -1,0x40000 irq 3 vect 0x75 533 ie2 at vme0 addr 0x31ff02,0x300000 len -1,0x40000 irq 3 vect 0x76 534 ie3 at vme0 addr 0x35ff02,0x300000 len -1,0x40000 irq 3 vect 0x77 535 ie4 at vme0 addr 0x2dff02,0x200000 len -1,0x40000 irq 3 vect 0x7c 536 537 ## Quad Ethernet Controller with BigMac (be, 10/100MBd) and Mace Ethernet 538 ## (qe, 10MBd) attached. 539 qec* at sbus? slot ? offset ? # Quad Ethernet Controller 540 be* at qec? # BigMac Ethernet (10/100MBd) 541 qe* at qec? # Mace Ethernet (10MBd) 542 543 ## Happy Meal Ethernet 544 hme* at sbus? slot ? offset ? 545 546 # midway ATM 547 en0 at sbus? slot ? offset ? 548 549 # PCMCIA ethernet devices 550 #ep* at pcmcia? 551 #mbe* at pcmcia? 552 #ne* at pcmcia? 553 #sm* at pcmcia? 554 555 # MII/PHY support 556 exphy* at mii? phy ? # 3Com internal PHYs 557 icsphy* at mii? phy ? # Integrated Circuit Systems ICS189x 558 inphy* at mii? phy ? # Intel 82555 PHYs 559 lxtphy* at mii? phy ? # Level One LXT-970 PHYs 560 nsphy* at mii? phy ? # NS83840 PHYs 561 qsphy* at mii? phy ? # Quality Semiconductor QS6612 PHYs 562 sqphy* at mii? phy ? # Seeq 80220/80221/80223 PHYs 563 tlphy* at mii? phy ? # ThunderLAN PHYs 564 ukphy* at mii? phy ? # generic unknown PHYs 565 566 ## Loopback network interface; required 567 pseudo-device loop 568 569 ## SLIP and CSLIP interfaces, for IP over a serial line. 570 pseudo-device sl 571 572 ## PPP, the successor to SLIP. See pppd(8). 573 pseudo-device ppp 574 575 ## PPP over Ethernet (RFC 2516) 576 pseudo-device pppoe 577 578 ## Starmode Radio IP, a special hardware network device. 579 #pseudo-device strip 580 581 ## Network "tunnel" device, allowing protocol stacks to run in the userland. 582 ## This is used by the third-party user-mode "ppp" program, and others. 583 pseudo-device tun 584 pseudo-device tap # virtual Ethernet 585 586 ## Generic L3 over IP tunnel 587 #pseudo-device gre # generic L3 over IP tunnel 588 589 ## Berkeley Packet Filter, required to run RARPD. A generic C-language 590 ## interface that allows selective examining of incoming packets. 591 pseudo-device bpfilter 592 593 #pseudo-device carp # Common Address Redundancy Protocol 594 595 ## IP Filter, used in firewall and NAT applications. See ipnat(8) for 596 ## one example of the use of the IP Filter. 597 pseudo-device ipfilter 598 599 ## for IPv6 600 pseudo-device gif # IPv[46] over IPv[46] tunnel (RFC1933) 601 #pseudo-device faith # IPv[46] tcp relay translation i/f 602 pseudo-device stf # 6to4 IPv6 over IPv4 encapsulation 603 604 ## IEEE 802.1Q Virtual LAN encapsulation, see vlan(4). 605 pseudo-device vlan 606 607 ## Simple inter-network traffic bridging 608 pseudo-device bridge 609 #options BRIDGE_IPF # bridge uses IP/IPv6 pfil hooks too 610 611 #### Audio and video devices 612 613 ## /dev/audio support (`audioamd' plus `audio') 614 ## 615 audioamd0 at mainbus0 # sun4c 616 audioamd0 at obio0 # sun4m 617 audioamd0 at sbus0 slot ? offset ? # sun4m 618 619 audiocs0 at sbus0 slot ? offset ? # SUNW,CS4231 620 621 #options DBRI_DEBUG # noisy debug output from the dbri driver 622 #options DBRI_BIG_BUFFER # use bigger DMA buffers, for slow CPUs 623 dbri* at sbus? slot ? offset ? # SUNW,DBRI[s3|e] 624 625 audio* at audiobus? 626 627 ## Sun "bwtwo" black and white framebuffer, found on sun4, sun4c, and sun4m 628 ## systems. If your sun4 system has a cgfour installed in the P4 slot, 629 ## the P4 entries for "bwtwo" will attach to the overlay plane of the 630 ## "cgfour". 631 632 bwtwo0 at sbus0 slot ? offset ? # sun4c and sun4m 633 bwtwo* at sbus? slot ? offset ? # 634 bwtwo0 at obio0 addr 0xfd000000 level 4 # sun4/200 635 bwtwo0 at obio0 addr 0xfb300000 level 4 # sun4/300 in P4 slot 636 bwtwo0 at obio0 addr 0x0b300000 level 4 # sun4/100 in P4 slot 637 638 ## Sun "cgtwo" VME color framebuffer 639 cgtwo0 at vme0 addr 0x400000 irq ? vect 0xa8 640 641 ## Sun "cgthree" Sbus color framebuffer 642 cgthree0 at sbus? slot ? offset ? 643 cgthree* at sbus? slot ? offset ? 644 #cgthree0 at obio? slot ? offset ? # sun4m 645 646 ## Sun "cgfour" color framebuffer with overlay plane. See above comment 647 ## regarding overlay plane. 648 cgfour0 at obio0 addr 0xfb300000 level 4 # sun4/300 P4 649 cgfour0 at obio0 addr 0x0b300000 level 4 # sun4/100 P4 650 651 ## Sun "cgsix" accelerated color framebuffer. 652 cgsix0 at sbus? slot ? offset ? 653 cgsix* at sbus? slot ? offset ? 654 cgsix0 at obio0 addr 0xfb000000 level 4 # sun4/300 P4 655 cgsix0 at obio0 addr 0x0b000000 level 4 # sun4/100 P4 656 657 ## Sun "cgeight" 24-bit framebuffer 658 cgeight0 at obio0 addr 0xfb300000 level 4 # sun4/300 P4 659 cgeight0 at obio0 addr 0x0b300000 level 4 # sun4/100 P4 660 661 ## Sun "tcx" accelerated color framebuffer. 662 tcx0 at sbus? slot ? offset ? 663 tcx* at sbus? slot ? offset ? 664 665 # Sun "cgfourteen" accelerated 24-bit framebuffer. 666 cgfourteen0 at obio0 # sun4m 667 668 # P9100-based display on Tadpole SPARCbook 3. 669 pnozz0 at sbus? slot ? offset ? 670 671 # Sun ZX/Leo 24-bit framebuffer 672 zx* at sbus? slot ? offset ? 673 674 #### Other device configuration 675 676 # Tadpole microcontroller 677 tctrl0 at obio0 678 679 ## Pseudo ttys, required for network logins and programs like screen. 680 681 pseudo-device pty # pseudo-terminals 682 683 ## Random device, used to implement /dev/random (a source of random noise), 684 ## and generate randomness for some kernel formulae. 685 686 pseudo-device rnd 687 688 # a pseudo device needed for Coda # also needs CODA (above) 689 pseudo-device vcoda 4 # coda minicache <-> venus comm. 690 691 pseudo-device clockctl # user control of clock subsystem 692 pseudo-device ksyms # /dev/ksyms 693 #pseudo-device pf # PF packet filter 694 #pseudo-device pflog # PF log if 695 pseudo-device fss 4 # file system snapshot device 696 697 # Veriexec 698 #options VERIFIED_EXEC 699 # 700 # a pseudo device needed for veriexec 701 #pseudo-device veriexec 1 702 # 703 # Uncomment the fingerprint methods below that are desired. Note that 704 # removing fingerprint methods will have almost no impact on the kernel 705 # code size. 706 # 707 #options VERIFIED_EXEC_FP_RMD160 708 #options VERIFIED_EXEC_FP_SHA256 709 #options VERIFIED_EXEC_FP_SHA384 710 #options VERIFIED_EXEC_FP_SHA512 711 #options VERIFIED_EXEC_FP_SHA1 712 #options VERIFIED_EXEC_FP_MD5 713 714
Indexes created Thu Oct 02 14:10:14 GMT 2025