GENERIC revision 1.205.4.2
1 # $NetBSD: GENERIC,v 1.205.4.2 2009/10/18 13:33:29 bouyer Exp $ 2 # 3 # GENERIC machine description file 4 # 5 # This machine description file is used to generate the default NetBSD 6 # kernel. The generic kernel does not include all options, subsystems 7 # and device drivers, but should be useful for most applications. 8 # 9 # The machine description file can be customised for your specific 10 # machine to reduce the kernel size and improve its performance. 11 # 12 # For further information on compiling NetBSD kernels, see the config(8) 13 # man page. 14 # 15 # For further information on hardware support for this architecture, see 16 # the intro(4) man page. For further information about kernel options 17 # for this architecture, see the options(4) man page. For an explanation 18 # of each device driver in this file see the section 4 man page for the 19 # device. 20 21 include "arch/sparc/conf/std.sparc" 22 23 options INCLUDE_CONFIG_FILE # embed config file in kernel binary 24 25 #ident "GENERIC-$Revision: 1.205.4.2 $" 26 27 maxusers 32 28 29 ## System kernel configuration. See options(4) for more detail. 30 31 32 # Options for variants of the Sun SPARC architecure. 33 # We currently support three architecture types; at least one is required. 34 options SUN4 # sun4/100, sun4/200, sun4/300 35 options SUN4C # sun4c - SS1, 1+, 2, ELC, SLC, IPC, IPX, etc. 36 options SUN4M # sun4m - SS10, SS20, Classic, etc. 37 options SUN4D # sun4d - SS1000, SC2000 38 39 options SUN4_MMU3L # sun4/400 3-level MMU 40 41 ## System options specific to the sparc machine type 42 43 # Blink the power LED on some machines to indicate the system load. 44 #options BLINK 45 46 ## Use a faster console than the PROM's slow drawing routines. Not needed 47 ## for headless (no framebuffer) machines. 48 ## These is obsolete for wscons kernels 49 #options RASTERCONSOLE # fast rasterop console 50 #options RASTERCONSOLE_FGCOL=WSCOL_BLACK 51 #options RASTERCONSOLE_BGCOL=WSCOL_WHITE 52 53 # wscons stuff 54 options WSEMUL_SUN 55 #options WSEMUL_VT100 56 options WSDISPLAY_COMPAT_RAWKBD 57 options WSDISPLAY_CUSTOM_OUTPUT 58 options WS_DEFAULT_FG=WSCOL_BLACK 59 options WS_DEFAULT_BG=WSCOL_LIGHT_WHITE 60 options WS_KERNEL_FG=WSCOL_GREEN 61 options WS_KERNEL_BG=WSCOL_LIGHT_WHITE 62 options WSDISPLAY_COMPAT_PCVT 63 options WSDISPLAY_COMPAT_SYSCONS 64 options WSDISPLAY_COMPAT_USL 65 66 options WSDISPLAY_SCROLLSUPPORT 67 68 # generic options vlid for both wscons and RASTERCONSOLE 69 options FONT_GALLANT12x22 # the console font 70 #options FONT_BOLD8x16 # a somewhat smaller font 71 72 #### System options that are the same for all ports 73 74 ## Root device configuration: change the ?'s if you are going to use a 75 ## nonstandard root partition (other than where the kernel is booted from) 76 ## and/or nonstandard root type (not ffs or nfs). Normally this can be 77 ## automagically determined at boot time. 78 79 config netbsd root on ? type ? 80 81 ## System call tracing (see ktrace(1)). 82 options KTRACE 83 84 ## Collect statistics on kernel malloc's and free's. This does have a 85 ## significant performance hit on slower machines, so it is intended for 86 ## diagnostic use only. 87 #options KMEMSTATS 88 89 ## System V compatible IPC subsystem. (msgctl(2), semctl(2), and shmctl(2)) 90 options SYSVMSG # System V message queues 91 options SYSVSEM # System V semaphores 92 options SYSVSHM # System V shared memory 93 options P1003_1B_SEMAPHORE # p1003.1b semaphore support 94 95 ## Loadable kernel module support; still under development. 96 options LKM 97 98 options USERCONF # userconf(4) support 99 #options PIPE_SOCKETPAIR # smaller, but slower pipe(2) 100 options SYSCTL_INCLUDE_DESCR # Include sysctl descriptions in kernel 101 102 # Enable experimental buffer queue strategy for better responsiveness under 103 # high disk I/O load. Use it with caution - it's not proven to be stable yet. 104 #options BUFQ_READPRIO 105 #options BUFQ_PRIOCSCAN 106 107 ## NFS boot options; tries DHCP/BOOTP then BOOTPARAM 108 options NFS_BOOT_BOOTPARAM 109 #options NFS_BOOT_BOOTP 110 options NFS_BOOT_DHCP 111 112 #### Debugging options 113 114 ## The DDB in-kernel debugger runs at panic (unless DDB_ONPANIC=0), or at 115 ## serial console break or keyboard reset, where the PROM would normally 116 ## intercept. DDB_HISTORY_SIZE adds up/down arrow command history. 117 options DDB # kernel dynamic debugger 118 options DDB_HISTORY_SIZE=100 # enable history editing in DDB 119 #options DDB_ONPANIC=1 # see also sysctl(8): `ddb.onpanic' 120 121 ## You may also use gdb, on another computer connected to this machine over 122 ## a serial port. Both KGDB_DEV and KGDB_DEVRATE should be specified; 123 ## KGDB_DEV is a dev_t encoded device number of the serial port to use, where 124 ## the minor device number encodes the PROM enumeration of the serial ports, 125 ## i.e.: 126 ## 0xc00 = ttya, 0xc01 = ttyb, 0xc02 = ttyc, 0xc03 = ttyd. 127 ## (Note: ttyc and ttyd are available only on some sun4 models) 128 #options KGDB # support for kernel gdb 129 #options KGDB_DEV=0xc01 # kgdb device number (this is `ttyb') 130 #options KGDB_DEVRATE=38400 # baud rate 131 132 133 ## Compile the kernel with debugging symbols (`netbsd.gdb' is the debug file), 134 ## such that gdb(1) can be used on a kernel coredump. 135 136 #makeoptions DEBUG="-g" 137 138 139 ## Adds code to the kernel that does internal consistency checks, and will 140 ## cause the kernel to panic if corruption of internal data structures 141 ## is detected. 142 #options DIAGNOSTIC # extra kernel sanity checking 143 144 ## Enable (possibly expensive) debugging code that may also display messages 145 ## on the system console 146 #options DEBUG 147 148 ## Make SCSI error messages more verbose when explaining their meanings. 149 options SCSIVERBOSE 150 151 options MIIVERBOSE # verbose PHY autoconfig messages 152 153 ## `INSECURE' turns off the kernel security level (securelevel = 0 always). 154 ## This allows writing to /dev/mem, loading kernel modules while multi-user, 155 ## and other insecurities good only for development work. Do not use this 156 ## option on a production machine. 157 #options INSECURE 158 159 ## `FDSCRIPTS' allows non-readable but executable scripts by providing a 160 ## pre-opened opaque file to the script interpreter. `SETUIDSCRIPTS', 161 ## which implies FDSCRIPTS, allows scripts to be set-user-id using the same 162 ## opaque file mechanism. Perl calls this "secure setuid scripts." 163 164 #options FDSCRIPTS 165 #options SETUIDSCRIPTS 166 167 ## Options for compatibility with previous releases foreign system binaries. 168 ## In the cases of COMPAT_SUNOS and COMPAT_SVR4, you may need to set up 169 ## additional user-level utilities or system configuration files. See 170 ## compat_sunos(8) and compat_svr4(8). 171 172 options COMPAT_43 # 4.3BSD system interfaces 173 options COMPAT_10 # NetBSD 1.0 binary compatibility 174 options COMPAT_11 # NetBSD 1.1 binary compatibility 175 options COMPAT_12 # NetBSD 1.2 binary compatibility 176 options COMPAT_13 # NetBSD 1.3 binary compatibility 177 options COMPAT_14 # NetBSD 1.4 binary compatibility 178 options COMPAT_15 # NetBSD 1.5 binary compatibility 179 options COMPAT_16 # NetBSD 1.6 binary compatibility 180 options COMPAT_20 # NetBSD 2.0 binary compatibility 181 options COMPAT_30 # NetBSD 3.0 binary compatibility 182 options COMPAT_40 # NetBSD 4.0 binary compatibility 183 options COMPAT_SUNOS # SunOS 4.x binary compatibility 184 options COMPAT_SVR4 # SunOS 5.x binary compatibility 185 options COMPAT_BSDPTY # /dev/[pt]ty?? ptys. 186 187 ## File systems. You probably need at least one of FFS or NFS. 188 file-system FFS # Berkeley Fast Filesystem 189 file-system NFS # Sun NFS-compatible filesystem client 190 file-system KERNFS # kernel data-structure filesystem 191 file-system NULLFS # NULL layered filesystem 192 file-system OVERLAY # overlay file system 193 file-system MFS # memory-based filesystem 194 file-system FDESC # user file descriptor filesystem 195 file-system UMAPFS # uid/gid remapping filesystem 196 file-system LFS # Log-based filesystem (still experimental) 197 file-system PORTAL # portal filesystem (still experimental) 198 file-system PROCFS # /proc 199 file-system CD9660 # ISO 9660 + Rock Ridge file system 200 file-system UNION # union file system 201 file-system MSDOSFS # MS-DOS FAT filesystem(s). 202 file-system CODA # Coda File System; also needs vcoda (below) 203 file-system PTYFS # /dev/pts/N support 204 #file-system TMPFS # Efficient memory file-system 205 #file-system UDF # experimental - OSTA UDF CD/DVD file-system 206 207 ## File system options. 208 options NFSSERVER # Sun NFS-compatible filesystem server 209 options QUOTA # FFS quotas 210 #options FFS_EI # FFS Endian Independent support 211 options SOFTDEP # FFS soft updates support. 212 options WAPBL # File system journaling support - Experimental 213 #options UFS_DIRHASH # UFS Large Directory Hashing - Experimental 214 #options FFS_NO_SNAPSHOT # No FFS snapshot support 215 216 ## Network protocol support. In most environments, INET is required. 217 options INET # IP (Internet Protocol) v4 218 options INET6 # IPV6 219 #options IPSEC # IP security 220 #options IPSEC_ESP # IP security (encryption part; define w/IPSEC) 221 #options IPSEC_NAT_T # IPsec NAT traversal (NAT-T) 222 #options IPSEC_DEBUG # debug for IP security 223 #options GATEWAY # packet forwarding ("router switch") 224 #options MROUTING # packet forwarding of multicast packets 225 #options PIM # Protocol Independent Multicast 226 #options DIRECTED_BROADCAST # allow broadcasts through routers 227 #options ISO,TPIP # OSI networking 228 #options EON # OSI tunneling over IP 229 #options NETATALK # AppleTalk (over Ethernet) protocol 230 options NTP # Network Time Protocol in-kernel support 231 #options PPS_SYNC # Add serial line synchronization for NTP 232 options PFIL_HOOKS # Add pfil(9) hooks, intended for custom LKMs. 233 options IPFILTER_LOG # Add ipmon(8) logging for ipfilter device 234 options IPFILTER_LOOKUP # ippool(8) support 235 #options IPFILTER_DEFAULT_BLOCK # block all packets by default 236 options PPP_BSDCOMP # Add BSD compression to ppp device 237 options PPP_DEFLATE # Add deflate (libz) compression to ppp device 238 options PPP_FILTER # Add active filters for ppp (via bpf) 239 240 #options ALTQ # Manipulate network interfaces' output queues 241 #options ALTQ_BLUE # Stochastic Fair Blue 242 #options ALTQ_CBQ # Class-Based Queueing 243 #options ALTQ_CDNR # Diffserv Traffic Conditioner 244 #options ALTQ_FIFOQ # First-In First-Out Queue 245 #options ALTQ_FLOWVALVE # RED/flow-valve (red-penalty-box) 246 #options ALTQ_HFSC # Hierarchical Fair Service Curve 247 #options ALTQ_LOCALQ # Local queueing discipline 248 #options ALTQ_PRIQ # Priority Queueing 249 #options ALTQ_RED # Random Early Detection 250 #options ALTQ_RIO # RED with IN/OUT 251 #options ALTQ_WFQ # Weighted Fair Queueing 252 253 254 255 #### Main bus and CPU .. all systems. 256 mainbus0 at root 257 cpu0 at mainbus0 258 cpuunit0 at mainbus0 # sun4d 259 cpuunit* at mainbus0 # sun4d 260 cpu0 at cpuunit0 # sun4d 261 262 #### Bus types found on SPARC systems. 263 264 sbus0 at mainbus0 # sun4c 265 obio0 at mainbus0 # sun4 and sun4m 266 sparcvme0 at mainbus0 # sun4 267 iommu0 at mainbus0 # sun4m 268 sbus0 at iommu0 # sun4m 269 sparcvme0 at iommu0 # sun4m 270 vme0 at sparcvme0 # MI VME attachment 271 bootbus0 at cpuunit0 # sun4d 272 bootbus* at cpuunit? # sun4d 273 274 ## SBus expander box 275 xbox* at sbus? slot ? offset ? 276 sbus* at xbox? 277 278 ## SBus to PCMCIA bridge 279 nell* at sbus? slot ? offset ? # PCMCIA bridge 280 pcmcia* at nell? 281 tslot* at sbus? slot ? offset ? # PCMCIA bridge (tadpole 3gx) 282 pcmcia* at tslot? 283 284 #### Standard system devices -- all required for a given architecture 285 286 ## Auxiliary system registers on sun4c and sun4m 287 auxreg0 at mainbus0 # sun4c 288 auxreg0 at obio0 # sun4m 289 auxiotwo0 at obio0 # only on Tadpole SPARCbook. 290 291 ## Power status and control register on Sun4m systems 292 power0 at obio0 293 294 ## Mostek clock found on 4/300, sun4c, sun4m and sun4d systems. 295 ## The Mostek clock NVRAM is the "eeprom" on sun4/300 systems. 296 clock0 at mainbus0 # sun4c 297 clock0 at obio0 # sun4m 298 clock0 at obio0 addr 0xf2000000 # sun4/300 299 clock0 at bootbus0 # sun4d 300 301 ## Intersil clock found on 4/100 and 4/200 systems. 302 oclock0 at obio0 addr 0xf3000000 # sun4/200 303 oclock0 at obio0 addr 0x03000000 # sun4/100 304 305 ## Memory error registers. 306 memreg0 at mainbus0 # sun4c 307 memreg0 at obio0 # sun4m 308 memreg0 at obio0 addr 0xf4000000 # sun4/200 and sun4/300 309 memreg0 at obio0 addr 0x04000000 # sun4/100 310 311 ## ECC memory control 312 eccmemctl0 at mainbus0 # sun4m 313 314 ## Timer chip found on 4/300, sun4c, and sun4m systems. 315 timer0 at mainbus0 # sun4c 316 timer0 at obio0 # sun4m 317 timer0 at obio0 addr 0xef000000 # sun4/300 318 319 ## EEPROM found on 4/100 and 4/200 systems. Note that the 4/300 320 ## doesn't use this driver; the `EEPROM' is in the NVRAM on the 321 ## Mostek clock chip on 4/300 systems. 322 eeprom0 at obio0 addr 0xf2000000 # sun4/200 323 eeprom0 at obio0 addr 0x02000000 # sun4/100 324 325 326 #### Serial port configuration 327 328 ## Zilog 8530 serial chips. Each has two-channels. 329 ## zs0 is ttya and ttyb. zs1 is the keyboard and mouse. 330 zs0 at mainbus0 # sun4c 331 zs0 at obio0 # sun4m 332 zs0 at obio0 addr 0xf1000000 level 12 # sun4/200 and sun4/300 333 zs0 at obio0 addr 0x01000000 level 12 # sun4/100 334 zs0 at bootbus0 # sun4d 335 336 zs1 at mainbus0 # sun4c 337 zs1 at obio0 # sun4m 338 zs1 at obio0 addr 0xf0000000 level 12 # sun4/200 and sun4/300 339 zs1 at obio0 addr 0x00000000 level 12 # sun4/100 340 zs1 at bootbus0 # sun4d 341 342 # old kbd and mouse attachments 343 #kbd0 at zs1 channel 0 # keyboard 344 #ms0 at zs1 channel 1 # mouse 345 zstty* at zs? 346 347 # these are for wscons 348 kbd0 at zstty? 349 ms0 at zstty? 350 wskbd* at wskbddev? 351 wsmouse* at wsmousedev? 352 353 zs2 at obio0 addr 0xe0000000 level 12 # sun4/300 354 zstty2 at zs2 channel 0 # ttyc 355 zstty3 at zs2 channel 1 # ttyd 356 357 zs* at bootbus? # sun4d 358 zstty* at zs? 359 360 ## NS16x50 serial chips and clones. Present on the 361 ## Sun JavaStation-1 and Tadpole SPARCbook 3 362 com* at obio0 # sun4m 363 364 # Parallel port. 365 bpp* at sbus? slot? offset ? 366 367 ## Magma Serial/Parallel driver 368 magma* at sbus? slot ? offset ? 369 mtty* at magma? 370 mbpp* at magma? 371 372 ## SUNW,spif Serial/Parallel driver 373 spif* at sbus? slot ? offset ? 374 stty* at spif? 375 sbpp* at spif? 376 377 ## PCMCIA serial interfaces 378 #com* at pcmcia? 379 #pcmcom* at pcmcia? 380 #com* at pcmcom? 381 382 #### Disk controllers and disks 383 384 # 385 386 ## The following flags may be set for the NCR53c94 based esp driver: 387 ## bits 0-7: disable disconnect/reselect for the corresponding target 388 ## bits 8-15: disable synchronous negotiation for target [bit-8] 389 390 ## sun4/300, sun4c, sun4m on-board SCSI, and FSBE/S SBus SCSI cards. 391 ## Both `dma' and `esp' are needed in all cases. 392 ## Two kinds of additional SBus SCSI interfaces are available. One uses 393 ## "esp at sbus" like the sun4c on-board; the other uses "esp at dma". 394 395 ## sun4/300 SCSI - an NCR53c94 or equivalent behind 396 ## an LSI Logic DMA controller 397 398 dma0 at obio0 addr 0xfa001000 level 4 # sun4/300 399 esp0 at obio0 addr 0xfa000000 level 4 flags 0x0000 # sun4/300 400 401 dma0 at sbus0 slot ? offset ? # sun4c/sun4m 402 esp0 at sbus0 slot ? offset ? flags 0x0000 # sun4c 403 esp0 at dma0 flags 0x0000 # sun4m 404 405 # FSBE/S SCSI & SunSwift Sbus FAS366 406 dma* at sbus? slot ? offset ? # SBus 407 esp* at sbus? slot ? offset ? flags 0x0000 # SBus 408 esp* at dma? flags 0x0000 # SBus 409 410 scsibus* at esp? 411 412 ## Qlogic ISP SBus SCSI Card 413 isp* at sbus? slot ? offset ? 414 scsibus* at isp? 415 416 ## NCR5380-based "Sun SCSI 3" VME SCSI controller. 417 ## This driver has several flags which may be enabled by OR'ing 418 ## the values and using the "flags" directive. 419 ## Valid flags are: 420 ## 421 ## 0x01 Use DMA (may be polled) 422 ## 0x02 Use DMA completion interrupts 423 ## 0x04 Allow disconnect/reselect 424 ## 425 ## E.g. the following would enable DMA, interrupts, and reselect: 426 ## si0 at vme0 addr 0x200000 irq 3 vect 0x40 flags 0x07 427 ## 428 ## By default, DMA is enabled in the driver. 429 430 si0 at vme0 addr 0x200000 irq 2 vect 0x40 431 scsibus* at si? 432 433 ## NCR5380-based "SCSI Weird" on-board SCSI interface found 434 ## on sun4/100 systems. The flags are the same as the "si" 435 ## controller. Note, while DMA is enabled by default, only 436 ## polled DMA works at this time, and reselects do not work 437 ## on this particular controller. 438 439 sw0 at obio0 addr 0x0a000000 level 3 440 scsibus* at sw? 441 442 ## PCMCIA SCSI controllers 443 #aic* at pcmcia? 444 #spc* at pcmcia? 445 #scsibus* at aic? 446 #scsibus* at spc? 447 448 449 ## These entries find devices on all SCSI busses and assign 450 ## unit numbers dynamically. 451 sd* at scsibus? target ? lun ? # SCSI disks 452 st* at scsibus? target ? lun ? # SCSI tapes 453 cd* at scsibus? target ? lun ? # SCSI CD-ROMs 454 ch* at scsibus? target ? lun ? # SCSI changer devices 455 ss* at scsibus? target ? lun ? # SCSI scanners 456 ses* at scsibus? target ? lun ? # SCSI SES/SAF-TE 457 uk* at scsibus? target ? lun ? # unknown SCSI 458 459 460 ## Xylogics 753 or 7053 VME SMD disk controllers and disks, found 461 ## on sun4 systems. 462 xdc0 at vme0 addr 0xee80 irq 3 vect 0x44 463 xdc1 at vme0 addr 0xee90 irq 3 vect 0x45 464 xdc2 at vme0 addr 0xeea0 irq 3 vect 0x46 465 xdc3 at vme0 addr 0xeeb0 irq 3 vect 0x47 466 xd* at xdc? drive ? 467 468 ## Xylogics 451 or 451 VME SMD disk controllers and disks, found 469 ## on sun4 systems. 470 xyc0 at vme0 addr 0xee40 irq 3 vect 0x48 471 xyc1 at vme0 addr 0xee48 irq 3 vect 0x49 472 xy* at xyc? drive ? 473 474 475 ## Floppy controller and drive found on SPARCstations. 476 477 fdc0 at mainbus0 # sun4c controller 478 fdc0 at obio0 # sun4m controller 479 fd* at fdc0 # the drive itself 480 481 ## PCMCIA IDE controllers 482 #wdc* at pcmcia? 483 #atabus* at ata? 484 #wd* at atabus? drive ? flags 0x0000 485 486 ## PCMCIA wavelan card 487 #wi* at pcmcia? function ? # Lucent WaveLan IEEE (802.11) 488 489 # 490 # accept filters 491 pseudo-device accf_data # "dataready" accept filter 492 pseudo-device accf_http # "httpready" accept filter 493 494 ## A disk-like interface to files. Can be used to create floppy, CD, 495 ## miniroot images, etc. 496 497 pseudo-device vnd 498 #options VND_COMPRESSION # compressed vnd(4) 499 500 ## Concatenated and striped disks; with this, you can create a software-based 501 ## disk array similar to a "RAID 0" setup. See ccd(4). 502 503 pseudo-device ccd 4 504 505 ## Cryptographic disk devices; See cgd(4) 506 507 #pseudo-device cgd 4 508 509 ## RAIDframe disk driver: software RAID driver. See raid(4). 510 511 pseudo-device raid 8 512 options RAID_AUTOCONFIG # auto-configuration of RAID components 513 # Options to enable various other RAIDframe RAID types. 514 # options RF_INCLUDE_EVENODD=1 515 # options RF_INCLUDE_RAID5_RS=1 516 # options RF_INCLUDE_PARITYLOGGING=1 517 # options RF_INCLUDE_CHAINDECLUSTER=1 518 # options RF_INCLUDE_INTERDECLUSTER=1 519 # options RF_INCLUDE_PARITY_DECLUSTERING=1 520 # options RF_INCLUDE_PARITY_DECLUSTERING_DS=1 521 522 523 ## Memory disk device, used on boot floppies with compressed 524 ## kernel-plus-root-disk images. 525 526 #pseudo-device md 1 527 528 529 #### Network interfaces 530 531 ## LANCE Ethernet - an AMD 7990 LANCE behind specialized DMA glue 532 ## Three flavors of additional SBus ethernets are available. One attaches 533 ## directly like the sun4c on-board, one uses the ledma device like the 534 ## sun4m on-board, and one uses the lebuffer device. 535 536 le0 at obio0 addr 0xf9000000 level 6 # sun4/300 537 le0 at sbus0 slot ? offset ? # sun4c on-board 538 ledma0 at sbus0 slot ? offset ? # sun4m on-board 539 le0 at ledma0 # sun4m on-board 540 le* at sbus? slot ? offset ? # SBus 541 ledma* at sbus? slot ? offset ? # SBus 542 le* at ledma? # SBus 543 lebuffer0 at sbus? slot ? offset ? # SBus 544 le0 at lebuffer? # SBus 545 lebuffer* at sbus? slot ? offset ? # SBus 546 le* at lebuffer? # SBus 547 548 549 ## sun4/100 and sun4/200 Ethernet - an Intel 82586 on-board 550 ## or on a Multibus/VME card. 551 ie0 at obio0 addr 0xf6000000 level 6 # sun4/200 on-board 552 ie0 at obio0 addr 0x06000000 level 6 # sun4/100 on-board 553 ## VME: the first [addr,len] pair specifies the device registers; 554 ## the second pair specifies the on-board memory buffer 555 ie1 at vme0 addr 0xe88000,0xe00000 len -1,0x40000 irq 3 vect 0x75 556 ie2 at vme0 addr 0x31ff02,0x300000 len -1,0x40000 irq 3 vect 0x76 557 ie3 at vme0 addr 0x35ff02,0x300000 len -1,0x40000 irq 3 vect 0x77 558 ie4 at vme0 addr 0x2dff02,0x200000 len -1,0x40000 irq 3 vect 0x7c 559 560 ## Quad Ethernet Controller with BigMac (be, 10/100MBd) and Mace Ethernet 561 ## (qe, 10MBd) attached. 562 qec* at sbus? slot ? offset ? # Quad Ethernet Controller 563 be* at qec? # BigMac Ethernet (10/100MBd) 564 qe* at qec? # Mace Ethernet (10MBd) 565 566 ## Happy Meal Ethernet 567 hme* at sbus? slot ? offset ? 568 569 # midway ATM 570 en0 at sbus? slot ? offset ? 571 572 # PCMCIA ethernet devices 573 #ep* at pcmcia? 574 #mbe* at pcmcia? 575 #ne* at pcmcia? 576 #sm* at pcmcia? 577 578 # MII/PHY support 579 exphy* at mii? phy ? # 3Com internal PHYs 580 icsphy* at mii? phy ? # Integrated Circuit Systems ICS189x 581 inphy* at mii? phy ? # Intel 82555 PHYs 582 lxtphy* at mii? phy ? # Level One LXT-970 PHYs 583 nsphy* at mii? phy ? # NS83840 PHYs 584 qsphy* at mii? phy ? # Quality Semiconductor QS6612 PHYs 585 sqphy* at mii? phy ? # Seeq 80220/80221/80223 PHYs 586 tlphy* at mii? phy ? # ThunderLAN PHYs 587 ukphy* at mii? phy ? # generic unknown PHYs 588 589 ## Loopback network interface; required 590 pseudo-device loop 591 592 ## SLIP and CSLIP interfaces, for IP over a serial line. 593 pseudo-device sl 594 595 ## PPP, the successor to SLIP. See pppd(8). 596 pseudo-device ppp 597 598 ## PPP over Ethernet (RFC 2516) 599 pseudo-device pppoe 600 601 ## Starmode Radio IP, a special hardware network device. 602 #pseudo-device strip 603 604 ## Network "tunnel" device, allowing protocol stacks to run in the userland. 605 ## This is used by the third-party user-mode "ppp" program, and others. 606 pseudo-device tun 607 pseudo-device tap # virtual Ethernet 608 609 ## Generic L3 over IP tunnel 610 #pseudo-device gre # generic L3 over IP tunnel 611 612 ## Berkeley Packet Filter, required to run RARPD. A generic C-language 613 ## interface that allows selective examining of incoming packets. 614 pseudo-device bpfilter 615 616 #pseudo-device carp # Common Address Redundancy Protocol 617 618 ## IP Filter, used in firewall and NAT applications. See ipnat(8) for 619 ## one example of the use of the IP Filter. 620 pseudo-device ipfilter 621 622 ## for IPv6 623 pseudo-device gif # IPv[46] over IPv[46] tunnel (RFC1933) 624 #pseudo-device faith # IPv[46] tcp relay translation i/f 625 pseudo-device stf # 6to4 IPv6 over IPv4 encapsulation 626 627 ## IEEE 802.1Q Virtual LAN encapsulation, see vlan(4). 628 pseudo-device vlan 629 630 ## Simple inter-network traffic bridging 631 pseudo-device bridge 632 #options BRIDGE_IPF # bridge uses IP/IPv6 pfil hooks too 633 pseudo-device agr # IEEE 802.3ad link aggregation 634 635 #### Audio and video devices 636 637 ## /dev/audio support (`audioamd' plus `audio') 638 ## 639 audioamd0 at mainbus0 # sun4c 640 audioamd0 at obio0 # sun4m 641 audioamd0 at sbus0 slot ? offset ? # sun4m 642 643 audiocs0 at sbus0 slot ? offset ? # SUNW,CS4231 644 645 #options DBRI_DEBUG # noisy debug output from the dbri driver 646 #options DBRI_BIG_BUFFER # use bigger DMA buffers, for slow CPUs 647 dbri* at sbus? slot ? offset ? # SUNW,DBRI[s3|e] 648 649 audio* at audiobus? 650 651 ## Sun "bwtwo" black and white framebuffer, found on sun4, sun4c, and sun4m 652 ## systems. If your sun4 system has a cgfour installed in the P4 slot, 653 ## the P4 entries for "bwtwo" will attach to the overlay plane of the 654 ## "cgfour". 655 656 bwtwo0 at sbus0 slot ? offset ? # sun4c and sun4m 657 bwtwo* at sbus? slot ? offset ? # 658 bwtwo0 at obio0 addr 0xfd000000 level 4 # sun4/200 659 bwtwo0 at obio0 addr 0xfb300000 level 4 # sun4/300 in P4 slot 660 bwtwo0 at obio0 addr 0x0b300000 level 4 # sun4/100 in P4 slot 661 662 ## Sun "cgtwo" VME color framebuffer 663 # XXX no wsdisplay support 664 #cgtwo0 at vme0 addr 0x400000 irq ? vect 0xa8 665 666 ## Sun "cgthree" Sbus color framebuffer 667 cgthree0 at sbus? slot ? offset ? 668 cgthree* at sbus? slot ? offset ? 669 #cgthree0 at obio? slot ? offset ? # sun4m 670 671 ## Sun "cgfour" color framebuffer with overlay plane. See above comment 672 ## regarding overlay plane. 673 # XXX no wsdisplay support 674 #cgfour0 at obio0 addr 0xfb300000 level 4 # sun4/300 P4 675 #cgfour0 at obio0 addr 0x0b300000 level 4 # sun4/100 P4 676 677 ## Sun "cgsix" accelerated color framebuffer. 678 cgsix0 at sbus? slot ? offset ? 679 cgsix* at sbus? slot ? offset ? 680 cgsix0 at obio0 addr 0xfb000000 level 4 # sun4/300 P4 681 cgsix0 at obio0 addr 0x0b000000 level 4 # sun4/100 P4 682 683 ## Sun "cgeight" 24-bit framebuffer 684 # XXX no wsdisplay support 685 #cgeight0 at obio0 addr 0xfb300000 level 4 # sun4/300 P4 686 #cgeight0 at obio0 addr 0x0b300000 level 4 # sun4/100 P4 687 688 ## Sun "tcx" accelerated color framebuffer. 689 # XXX no wsdisplay support 690 #tcx0 at sbus? slot ? offset ? 691 #tcx* at sbus? slot ? offset ? 692 693 # Sun "cgfourteen" accelerated 24-bit framebuffer. 694 cgfourteen* at obio0 # sun4m 695 696 # P9100-based display on Tadpole SPARCbook 3. 697 pnozz0 at sbus? slot ? offset ? 698 699 # Sun ZX/Leo 24-bit framebuffer 700 # XXX no wsdisplay support 701 #zx* at sbus? slot ? offset ? 702 703 # Fujitsu AG-10e accelerated graphics 8/24-bit board 704 agten* at sbus? slot ? offset ? 705 706 # make sure wsdisplay0 is the console 707 wsdisplay0 at wsemuldisplaydev? console 1 708 wsdisplay* at wsemuldisplaydev? 709 710 #### Other device configuration 711 712 # Tadpole microcontroller 713 tctrl0 at obio0 714 715 ## Pseudo ttys, required for network logins and programs like screen. 716 717 pseudo-device pty # pseudo-terminals 718 719 ## Random device, used to implement /dev/random (a source of random noise), 720 ## and generate randomness for some kernel formulae. 721 722 pseudo-device rnd 723 724 # a pseudo device needed for Coda # also needs CODA (above) 725 pseudo-device vcoda 4 # coda minicache <-> venus comm. 726 727 pseudo-device clockctl # user control of clock subsystem 728 pseudo-device ksyms # /dev/ksyms 729 #pseudo-device pf # PF packet filter 730 #pseudo-device pflog # PF log if 731 pseudo-device fss 4 # file system snapshot device 732 pseudo-device wsmux # mouse and keyboard multiplexor 733 pseudo-device wsfont 734 735 #options FILEASSOC # fileassoc(9) 736 737 # Veriexec 738 # 739 # a pseudo device needed for veriexec 740 #pseudo-device veriexec 1 741 # 742 # Uncomment the fingerprint methods below that are desired. Note that 743 # removing fingerprint methods will have almost no impact on the kernel 744 # code size. 745 # 746 #options VERIFIED_EXEC_FP_RMD160 747 #options VERIFIED_EXEC_FP_SHA256 748 #options VERIFIED_EXEC_FP_SHA384 749 #options VERIFIED_EXEC_FP_SHA512 750 #options VERIFIED_EXEC_FP_SHA1 751 #options VERIFIED_EXEC_FP_MD5 752 753 #options PAX_MPROTECT=0 # PaX mprotect(2) restrictions 754 # (for static binaries only for now) 755
Indexes created Wed Oct 22 13:09:56 GMT 2025