GENERIC revision 1.210
1# $NetBSD: GENERIC,v 1.210 2009/01/27 06:57:59 mrg Exp $ 2# 3# GENERIC machine description file 4# 5# This machine description file is used to generate the default NetBSD 6# kernel. The generic kernel does not include all options, subsystems 7# and device drivers, but should be useful for most applications. 8# 9# The machine description file can be customised for your specific 10# machine to reduce the kernel size and improve its performance. 11# 12# For further information on compiling NetBSD kernels, see the config(8) 13# man page. 14# 15# For further information on hardware support for this architecture, see 16# the intro(4) man page. For further information about kernel options 17# for this architecture, see the options(4) man page. For an explanation 18# of each device driver in this file see the section 4 man page for the 19# device. 20 21include "arch/sparc/conf/std.sparc" 22 23options INCLUDE_CONFIG_FILE # embed config file in kernel binary 24 25#ident "GENERIC-$Revision: 1.210 $" 26 27maxusers 32 28 29## System kernel configuration. See options(4) for more detail. 30 31 32# Options for variants of the Sun SPARC architecure. 33# We currently support three architecture types; at least one is required. 34options SUN4 # sun4/100, sun4/200, sun4/300 35options SUN4C # sun4c - SS1, 1+, 2, ELC, SLC, IPC, IPX, etc. 36options SUN4M # sun4m - SS10, SS20, Classic, etc. 37options SUN4D # sun4d - SS1000, SC2000 38 39options SUN4_MMU3L # sun4/400 3-level MMU 40 41## System options specific to the sparc machine type 42 43# Blink the power LED on some machines to indicate the system load. 44#options BLINK 45 46## Use a faster console than the PROM's slow drawing routines. Not needed 47## for headless (no framebuffer) machines. 48## These is obsolete for wscons kernels 49#options RASTERCONSOLE # fast rasterop console 50#options RASTERCONSOLE_FGCOL=WSCOL_BLACK 51#options RASTERCONSOLE_BGCOL=WSCOL_WHITE 52 53# wscons stuff 54options WSEMUL_SUN 55#options WSEMUL_VT100 56options WSDISPLAY_COMPAT_RAWKBD 57options WSDISPLAY_CUSTOM_OUTPUT 58options WS_DEFAULT_FG=WSCOL_BLACK 59options WS_DEFAULT_BG=WSCOL_LIGHT_WHITE 60options WS_KERNEL_FG=WSCOL_GREEN 61options WS_KERNEL_BG=WSCOL_LIGHT_WHITE 62options WSDISPLAY_COMPAT_PCVT 63options WSDISPLAY_COMPAT_SYSCONS 64options WSDISPLAY_COMPAT_USL 65 66options WSDISPLAY_SCROLLSUPPORT 67 68# generic options vlid for both wscons and RASTERCONSOLE 69options FONT_GALLANT12x22 # the console font 70#options FONT_BOLD8x16 # a somewhat smaller font 71 72#### System options that are the same for all ports 73 74## Root device configuration: change the ?'s if you are going to use a 75## nonstandard root partition (other than where the kernel is booted from) 76## and/or nonstandard root type (not ffs or nfs). Normally this can be 77## automagically determined at boot time. 78 79config netbsd root on ? type ? 80 81## System call tracing (see ktrace(1)). 82options KTRACE 83 84## Collect statistics on kernel malloc's and free's. This does have a 85## significant performance hit on slower machines, so it is intended for 86## diagnostic use only. 87#options KMEMSTATS 88 89## System V compatible IPC subsystem. (msgctl(2), semctl(2), and shmctl(2)) 90options SYSVMSG # System V message queues 91options SYSVSEM # System V semaphores 92options SYSVSHM # System V shared memory 93options P1003_1B_SEMAPHORE # p1003.1b semaphore support 94 95## Loadable kernel module support; still under development. 96 97options USERCONF # userconf(4) support 98#options PIPE_SOCKETPAIR # smaller, but slower pipe(2) 99options SYSCTL_INCLUDE_DESCR # Include sysctl descriptions in kernel 100 101# Enable experimental buffer queue strategy for better responsiveness under 102# high disk I/O load. Use it with caution - it's not proven to be stable yet. 103#options BUFQ_READPRIO 104#options BUFQ_PRIOCSCAN 105 106## NFS boot options; tries DHCP/BOOTP then BOOTPARAM 107options NFS_BOOT_BOOTPARAM 108#options NFS_BOOT_BOOTP 109options NFS_BOOT_DHCP 110 111#### Debugging options 112 113## The DDB in-kernel debugger runs at panic (unless DDB_ONPANIC=0), or at 114## serial console break or keyboard reset, where the PROM would normally 115## intercept. DDB_HISTORY_SIZE adds up/down arrow command history. 116#options DDB # kernel dynamic debugger 117#options DDB_HISTORY_SIZE=100 # enable history editing in DDB 118#options DDB_ONPANIC=1 # see also sysctl(8): `ddb.onpanic' 119 120## You may also use gdb, on another computer connected to this machine over 121## a serial port. Both KGDB_DEV and KGDB_DEVRATE should be specified; 122## KGDB_DEV is a dev_t encoded device number of the serial port to use, where 123## the minor device number encodes the PROM enumeration of the serial ports, 124## i.e.: 125## 0xc00 = ttya, 0xc01 = ttyb, 0xc02 = ttyc, 0xc03 = ttyd. 126## (Note: ttyc and ttyd are available only on some sun4 models) 127#options KGDB # support for kernel gdb 128#options KGDB_DEV=0xc01 # kgdb device number (this is `ttyb') 129#options KGDB_DEVRATE=38400 # baud rate 130 131 132## Compile the kernel with debugging symbols (`netbsd.gdb' is the debug file), 133## such that gdb(1) can be used on a kernel coredump. 134 135#makeoptions DEBUG="-g" 136 137 138## Adds code to the kernel that does internal consistency checks, and will 139## cause the kernel to panic if corruption of internal data structures 140## is detected. 141#options DIAGNOSTIC # extra kernel sanity checking 142 143## Enable (possibly expensive) debugging code that may also display messages 144## on the system console 145#options DEBUG 146 147## Make SCSI error messages more verbose when explaining their meanings. 148options SCSIVERBOSE 149 150options MIIVERBOSE # verbose PHY autoconfig messages 151 152## `INSECURE' turns off the kernel security level (securelevel = 0 always). 153## This allows writing to /dev/mem, loading kernel modules while multi-user, 154## and other insecurities good only for development work. Do not use this 155## option on a production machine. 156#options INSECURE 157 158## `FDSCRIPTS' allows non-readable but executable scripts by providing a 159## pre-opened opaque file to the script interpreter. `SETUIDSCRIPTS', 160## which implies FDSCRIPTS, allows scripts to be set-user-id using the same 161## opaque file mechanism. Perl calls this "secure setuid scripts." 162 163#options FDSCRIPTS 164#options SETUIDSCRIPTS 165 166## Options for compatibility with previous releases foreign system binaries. 167## In the cases of COMPAT_SUNOS and COMPAT_SVR4, you may need to set up 168## additional user-level utilities or system configuration files. See 169## compat_sunos(8) and compat_svr4(8). 170 171options COMPAT_43 # 4.3BSD system interfaces 172options COMPAT_10 # NetBSD 1.0 binary compatibility 173options COMPAT_11 # NetBSD 1.1 binary compatibility 174options COMPAT_12 # NetBSD 1.2 binary compatibility 175options COMPAT_13 # NetBSD 1.3 binary compatibility 176options COMPAT_14 # NetBSD 1.4 binary compatibility 177options COMPAT_15 # NetBSD 1.5 binary compatibility 178options COMPAT_16 # NetBSD 1.6 binary compatibility 179options COMPAT_20 # NetBSD 2.0 binary compatibility 180options COMPAT_30 # NetBSD 3.0 binary compatibility 181options COMPAT_40 # NetBSD 4.0 binary compatibility 182options COMPAT_50 # NetBSD 5.0 binary compatibility 183options COMPAT_SUNOS # SunOS 4.x binary compatibility 184options COMPAT_SVR4 # SunOS 5.x binary compatibility 185options COMPAT_BSDPTY # /dev/[pt]ty?? ptys. 186 187## File systems. You probably need at least one of FFS or NFS. 188file-system FFS # Berkeley Fast Filesystem 189file-system NFS # Sun NFS-compatible filesystem client 190file-system KERNFS # kernel data-structure filesystem 191file-system NULLFS # NULL layered filesystem 192file-system OVERLAY # overlay file system 193file-system MFS # memory-based filesystem 194file-system FDESC # user file descriptor filesystem 195file-system UMAPFS # uid/gid remapping filesystem 196file-system LFS # Log-based filesystem (still experimental) 197file-system PORTAL # portal filesystem (still experimental) 198file-system PROCFS # /proc 199file-system CD9660 # ISO 9660 + Rock Ridge file system 200file-system UNION # union file system 201file-system MSDOSFS # MS-DOS FAT filesystem(s). 202file-system CODA # Coda File System; also needs vcoda (below) 203file-system PTYFS # /dev/pts/N support 204#file-system TMPFS # Efficient memory file-system 205#file-system UDF # experimental - OSTA UDF CD/DVD file-system 206 207## File system options. 208options NFSSERVER # Sun NFS-compatible filesystem server 209options QUOTA # FFS quotas 210#options FFS_EI # FFS Endian Independent support 211options WAPBL # File system journaling support - Experimental 212#options UFS_DIRHASH # UFS Large Directory Hashing - Experimental 213#options FFS_NO_SNAPSHOT # No FFS snapshot support 214 215## Network protocol support. In most environments, INET is required. 216options INET # IP (Internet Protocol) v4 217options INET6 # IPV6 218#options IPSEC # IP security 219#options IPSEC_ESP # IP security (encryption part; define w/IPSEC) 220#options IPSEC_NAT_T # IPsec NAT traversal (NAT-T) 221#options IPSEC_DEBUG # debug for IP security 222#options GATEWAY # packet forwarding ("router switch") 223#options MROUTING # packet forwarding of multicast packets 224#options PIM # Protocol Independent Multicast 225#options DIRECTED_BROADCAST # allow broadcasts through routers 226#options ISO,TPIP # OSI networking 227#options EON # OSI tunneling over IP 228#options NETATALK # AppleTalk (over Ethernet) protocol 229options NTP # Network Time Protocol in-kernel support 230#options PPS_SYNC # Add serial line synchronization for NTP 231options PFIL_HOOKS # Add pfil(9) hooks, intended for custom LKMs. 232options IPFILTER_LOG # Add ipmon(8) logging for ipfilter device 233options IPFILTER_LOOKUP # ippool(8) support 234#options IPFILTER_DEFAULT_BLOCK # block all packets by default 235options PPP_BSDCOMP # Add BSD compression to ppp device 236options PPP_DEFLATE # Add deflate (libz) compression to ppp device 237options PPP_FILTER # Add active filters for ppp (via bpf) 238 239#options ALTQ # Manipulate network interfaces' output queues 240#options ALTQ_BLUE # Stochastic Fair Blue 241#options ALTQ_CBQ # Class-Based Queueing 242#options ALTQ_CDNR # Diffserv Traffic Conditioner 243#options ALTQ_FIFOQ # First-In First-Out Queue 244#options ALTQ_FLOWVALVE # RED/flow-valve (red-penalty-box) 245#options ALTQ_HFSC # Hierarchical Fair Service Curve 246#options ALTQ_LOCALQ # Local queueing discipline 247#options ALTQ_PRIQ # Priority Queueing 248#options ALTQ_RED # Random Early Detection 249#options ALTQ_RIO # RED with IN/OUT 250#options ALTQ_WFQ # Weighted Fair Queueing 251 252 253 254#### Main bus and CPU .. all systems. 255mainbus0 at root 256cpu0 at mainbus0 257cpuunit0 at mainbus0 # sun4d 258cpuunit* at mainbus0 # sun4d 259cpu0 at cpuunit0 # sun4d 260 261#### Bus types found on SPARC systems. 262 263sbus0 at mainbus0 # sun4c 264obio0 at mainbus0 # sun4 and sun4m 265sparcvme0 at mainbus0 # sun4 266iommu0 at mainbus0 # sun4m 267sbus0 at iommu0 # sun4m 268sparcvme0 at iommu0 # sun4m 269vme0 at sparcvme0 # MI VME attachment 270bootbus0 at cpuunit0 # sun4d 271bootbus* at cpuunit? # sun4d 272 273## SBus expander box 274xbox* at sbus? slot ? offset ? 275sbus* at xbox? 276 277## SBus to PCMCIA bridge 278nell* at sbus? slot ? offset ? # PCMCIA bridge 279pcmcia* at nell? 280tslot* at sbus? slot ? offset ? # PCMCIA bridge (tadpole 3gx) 281pcmcia* at tslot? 282 283#### Standard system devices -- all required for a given architecture 284 285## Auxiliary system registers on sun4c and sun4m 286auxreg0 at mainbus0 # sun4c 287auxreg0 at obio0 # sun4m 288auxiotwo0 at obio0 # only on Tadpole SPARCbook. 289 290## Power status and control register on Sun4m systems 291power0 at obio0 292 293## Mostek clock found on 4/300, sun4c, sun4m and sun4d systems. 294## The Mostek clock NVRAM is the "eeprom" on sun4/300 systems. 295clock0 at mainbus0 # sun4c 296clock0 at obio0 # sun4m 297clock0 at obio0 addr 0xf2000000 # sun4/300 298clock0 at bootbus0 # sun4d 299 300## Intersil clock found on 4/100 and 4/200 systems. 301oclock0 at obio0 addr 0xf3000000 # sun4/200 302oclock0 at obio0 addr 0x03000000 # sun4/100 303 304## Memory error registers. 305memreg0 at mainbus0 # sun4c 306memreg0 at obio0 # sun4m 307memreg0 at obio0 addr 0xf4000000 # sun4/200 and sun4/300 308memreg0 at obio0 addr 0x04000000 # sun4/100 309 310## ECC memory control 311eccmemctl0 at mainbus0 # sun4m 312 313## Timer chip found on 4/300, sun4c, and sun4m systems. 314timer0 at mainbus0 # sun4c 315timer0 at obio0 # sun4m 316timer0 at obio0 addr 0xef000000 # sun4/300 317 318## EEPROM found on 4/100 and 4/200 systems. Note that the 4/300 319## doesn't use this driver; the `EEPROM' is in the NVRAM on the 320## Mostek clock chip on 4/300 systems. 321eeprom0 at obio0 addr 0xf2000000 # sun4/200 322eeprom0 at obio0 addr 0x02000000 # sun4/100 323 324 325#### Serial port configuration 326 327## Zilog 8530 serial chips. Each has two-channels. 328## zs0 is ttya and ttyb. zs1 is the keyboard and mouse. 329zs0 at mainbus0 # sun4c 330zs0 at obio0 # sun4m 331zs0 at obio0 addr 0xf1000000 level 12 # sun4/200 and sun4/300 332zs0 at obio0 addr 0x01000000 level 12 # sun4/100 333zs0 at bootbus0 # sun4d 334 335zs1 at mainbus0 # sun4c 336zs1 at obio0 # sun4m 337zs1 at obio0 addr 0xf0000000 level 12 # sun4/200 and sun4/300 338zs1 at obio0 addr 0x00000000 level 12 # sun4/100 339zs1 at bootbus0 # sun4d 340 341# old kbd and mouse attachments 342#kbd0 at zs1 channel 0 # keyboard 343#ms0 at zs1 channel 1 # mouse 344zstty* at zs? 345 346# these are for wscons 347kbd0 at zstty? 348ms0 at zstty? 349wskbd* at wskbddev? 350wsmouse* at wsmousedev? 351 352zs2 at obio0 addr 0xe0000000 level 12 # sun4/300 353zstty2 at zs2 channel 0 # ttyc 354zstty3 at zs2 channel 1 # ttyd 355 356zs* at bootbus? # sun4d 357zstty* at zs? 358 359## NS16x50 serial chips and clones. Present on the 360## Sun JavaStation-1 and Tadpole SPARCbook 3 361com* at obio0 # sun4m 362 363# Parallel port. 364bpp* at sbus? slot? offset ? 365 366## Magma Serial/Parallel driver 367magma* at sbus? slot ? offset ? 368mtty* at magma? 369mbpp* at magma? 370 371## SUNW,spif Serial/Parallel driver 372spif* at sbus? slot ? offset ? 373stty* at spif? 374sbpp* at spif? 375 376## PCMCIA serial interfaces 377#com* at pcmcia? 378#pcmcom* at pcmcia? 379#com* at pcmcom? 380 381#### Disk controllers and disks 382 383# 384 385## The following flags may be set for the NCR53c94 based esp driver: 386## bits 0-7: disable disconnect/reselect for the corresponding target 387## bits 8-15: disable synchronous negotiation for target [bit-8] 388 389## sun4/300, sun4c, sun4m on-board SCSI, and FSBE/S SBus SCSI cards. 390## Both `dma' and `esp' are needed in all cases. 391## Two kinds of additional SBus SCSI interfaces are available. One uses 392## "esp at sbus" like the sun4c on-board; the other uses "esp at dma". 393 394## sun4/300 SCSI - an NCR53c94 or equivalent behind 395## an LSI Logic DMA controller 396 397dma0 at obio0 addr 0xfa001000 level 4 # sun4/300 398esp0 at obio0 addr 0xfa000000 level 4 flags 0x0000 # sun4/300 399 400dma0 at sbus0 slot ? offset ? # sun4c/sun4m 401esp0 at sbus0 slot ? offset ? flags 0x0000 # sun4c 402esp0 at dma0 flags 0x0000 # sun4m 403 404# FSBE/S SCSI & SunSwift Sbus FAS366 405dma* at sbus? slot ? offset ? # SBus 406esp* at sbus? slot ? offset ? flags 0x0000 # SBus 407esp* at dma? flags 0x0000 # SBus 408 409scsibus* at esp? 410 411## Qlogic ISP SBus SCSI Card 412isp* at sbus? slot ? offset ? 413scsibus* at isp? 414 415## NCR5380-based "Sun SCSI 3" VME SCSI controller. 416## This driver has several flags which may be enabled by OR'ing 417## the values and using the "flags" directive. 418## Valid flags are: 419## 420## 0x01 Use DMA (may be polled) 421## 0x02 Use DMA completion interrupts 422## 0x04 Allow disconnect/reselect 423## 424## E.g. the following would enable DMA, interrupts, and reselect: 425## si0 at vme0 addr 0x200000 irq 3 vect 0x40 flags 0x07 426## 427## By default, DMA is enabled in the driver. 428 429si0 at vme0 addr 0x200000 irq 2 vect 0x40 430scsibus* at si? 431 432## NCR5380-based "SCSI Weird" on-board SCSI interface found 433## on sun4/100 systems. The flags are the same as the "si" 434## controller. Note, while DMA is enabled by default, only 435## polled DMA works at this time, and reselects do not work 436## on this particular controller. 437 438sw0 at obio0 addr 0x0a000000 level 3 439scsibus* at sw? 440 441## PCMCIA SCSI controllers 442#aic* at pcmcia? 443#spc* at pcmcia? 444#scsibus* at aic? 445#scsibus* at spc? 446 447 448## These entries find devices on all SCSI busses and assign 449## unit numbers dynamically. 450sd* at scsibus? target ? lun ? # SCSI disks 451st* at scsibus? target ? lun ? # SCSI tapes 452cd* at scsibus? target ? lun ? # SCSI CD-ROMs 453ch* at scsibus? target ? lun ? # SCSI changer devices 454ss* at scsibus? target ? lun ? # SCSI scanners 455ses* at scsibus? target ? lun ? # SCSI SES/SAF-TE 456uk* at scsibus? target ? lun ? # unknown SCSI 457 458 459## Xylogics 753 or 7053 VME SMD disk controllers and disks, found 460## on sun4 systems. 461xdc0 at vme0 addr 0xee80 irq 3 vect 0x44 462xdc1 at vme0 addr 0xee90 irq 3 vect 0x45 463xdc2 at vme0 addr 0xeea0 irq 3 vect 0x46 464xdc3 at vme0 addr 0xeeb0 irq 3 vect 0x47 465xd* at xdc? drive ? 466 467## Xylogics 451 or 451 VME SMD disk controllers and disks, found 468## on sun4 systems. 469xyc0 at vme0 addr 0xee40 irq 3 vect 0x48 470xyc1 at vme0 addr 0xee48 irq 3 vect 0x49 471xy* at xyc? drive ? 472 473 474## Floppy controller and drive found on SPARCstations. 475 476fdc0 at mainbus0 # sun4c controller 477fdc0 at obio0 # sun4m controller 478fd* at fdc0 # the drive itself 479 480## PCMCIA IDE controllers 481#wdc* at pcmcia? 482#atabus* at ata? 483#wd* at atabus? drive ? flags 0x0000 484 485## PCMCIA wavelan card 486#wi* at pcmcia? function ? # Lucent WaveLan IEEE (802.11) 487 488# 489# accept filters 490pseudo-device accf_data # "dataready" accept filter 491pseudo-device accf_http # "httpready" accept filter 492 493## A disk-like interface to files. Can be used to create floppy, CD, 494## miniroot images, etc. 495 496pseudo-device vnd 497#options VND_COMPRESSION # compressed vnd(4) 498 499## Concatenated and striped disks; with this, you can create a software-based 500## disk array similar to a "RAID 0" setup. See ccd(4). 501 502pseudo-device ccd 4 503 504## Cryptographic disk devices; See cgd(4) 505 506#pseudo-device cgd 4 507 508## RAIDframe disk driver: software RAID driver. See raid(4). 509 510pseudo-device raid 8 511options RAID_AUTOCONFIG # auto-configuration of RAID components 512# Options to enable various other RAIDframe RAID types. 513# options RF_INCLUDE_EVENODD=1 514# options RF_INCLUDE_RAID5_RS=1 515# options RF_INCLUDE_PARITYLOGGING=1 516# options RF_INCLUDE_CHAINDECLUSTER=1 517# options RF_INCLUDE_INTERDECLUSTER=1 518# options RF_INCLUDE_PARITY_DECLUSTERING=1 519# options RF_INCLUDE_PARITY_DECLUSTERING_DS=1 520 521 522## Memory disk device, used on boot floppies with compressed 523## kernel-plus-root-disk images. 524 525#pseudo-device md 1 526 527 528#### Network interfaces 529 530## LANCE Ethernet - an AMD 7990 LANCE behind specialized DMA glue 531## Three flavors of additional SBus ethernets are available. One attaches 532## directly like the sun4c on-board, one uses the ledma device like the 533## sun4m on-board, and one uses the lebuffer device. 534 535le0 at obio0 addr 0xf9000000 level 6 # sun4/300 536le0 at sbus0 slot ? offset ? # sun4c on-board 537ledma0 at sbus0 slot ? offset ? # sun4m on-board 538le0 at ledma0 # sun4m on-board 539le* at sbus? slot ? offset ? # SBus 540ledma* at sbus? slot ? offset ? # SBus 541le* at ledma? # SBus 542lebuffer0 at sbus? slot ? offset ? # SBus 543le0 at lebuffer? # SBus 544lebuffer* at sbus? slot ? offset ? # SBus 545le* at lebuffer? # SBus 546 547 548## sun4/100 and sun4/200 Ethernet - an Intel 82586 on-board 549## or on a Multibus/VME card. 550ie0 at obio0 addr 0xf6000000 level 6 # sun4/200 on-board 551ie0 at obio0 addr 0x06000000 level 6 # sun4/100 on-board 552## VME: the first [addr,len] pair specifies the device registers; 553## the second pair specifies the on-board memory buffer 554ie1 at vme0 addr 0xe88000,0xe00000 len -1,0x40000 irq 3 vect 0x75 555ie2 at vme0 addr 0x31ff02,0x300000 len -1,0x40000 irq 3 vect 0x76 556ie3 at vme0 addr 0x35ff02,0x300000 len -1,0x40000 irq 3 vect 0x77 557ie4 at vme0 addr 0x2dff02,0x200000 len -1,0x40000 irq 3 vect 0x7c 558 559## Quad Ethernet Controller with BigMac (be, 10/100MBd) and Mace Ethernet 560## (qe, 10MBd) attached. 561qec* at sbus? slot ? offset ? # Quad Ethernet Controller 562be* at qec? # BigMac Ethernet (10/100MBd) 563qe* at qec? # Mace Ethernet (10MBd) 564 565## Happy Meal Ethernet 566hme* at sbus? slot ? offset ? 567 568# midway ATM 569en0 at sbus? slot ? offset ? 570 571# PCMCIA ethernet devices 572#ep* at pcmcia? 573#mbe* at pcmcia? 574#ne* at pcmcia? 575#sm* at pcmcia? 576 577# MII/PHY support 578exphy* at mii? phy ? # 3Com internal PHYs 579icsphy* at mii? phy ? # Integrated Circuit Systems ICS189x 580inphy* at mii? phy ? # Intel 82555 PHYs 581lxtphy* at mii? phy ? # Level One LXT-970 PHYs 582nsphy* at mii? phy ? # NS83840 PHYs 583qsphy* at mii? phy ? # Quality Semiconductor QS6612 PHYs 584sqphy* at mii? phy ? # Seeq 80220/80221/80223 PHYs 585tlphy* at mii? phy ? # ThunderLAN PHYs 586ukphy* at mii? phy ? # generic unknown PHYs 587 588## Loopback network interface; required 589pseudo-device loop 590 591## SLIP and CSLIP interfaces, for IP over a serial line. 592pseudo-device sl 593 594## PPP, the successor to SLIP. See pppd(8). 595pseudo-device ppp 596 597## PPP over Ethernet (RFC 2516) 598pseudo-device pppoe 599 600## Starmode Radio IP, a special hardware network device. 601#pseudo-device strip 602 603## Network "tunnel" device, allowing protocol stacks to run in the userland. 604## This is used by the third-party user-mode "ppp" program, and others. 605pseudo-device tun 606pseudo-device tap # virtual Ethernet 607 608## Generic L3 over IP tunnel 609#pseudo-device gre # generic L3 over IP tunnel 610 611## Berkeley Packet Filter, required to run RARPD. A generic C-language 612## interface that allows selective examining of incoming packets. 613pseudo-device bpfilter 614 615#pseudo-device carp # Common Address Redundancy Protocol 616 617## IP Filter, used in firewall and NAT applications. See ipnat(8) for 618## one example of the use of the IP Filter. 619pseudo-device ipfilter 620 621## for IPv6 622pseudo-device gif # IPv[46] over IPv[46] tunnel (RFC1933) 623#pseudo-device faith # IPv[46] tcp relay translation i/f 624pseudo-device stf # 6to4 IPv6 over IPv4 encapsulation 625 626## IEEE 802.1Q Virtual LAN encapsulation, see vlan(4). 627pseudo-device vlan 628 629## Simple inter-network traffic bridging 630pseudo-device bridge 631#options BRIDGE_IPF # bridge uses IP/IPv6 pfil hooks too 632pseudo-device agr # IEEE 802.3ad link aggregation 633 634#### Audio and video devices 635 636## /dev/audio support (`audioamd' plus `audio') 637## 638audioamd0 at mainbus0 # sun4c 639audioamd0 at obio0 # sun4m 640audioamd0 at sbus0 slot ? offset ? # sun4m 641 642audiocs0 at sbus0 slot ? offset ? # SUNW,CS4231 643 644#options DBRI_DEBUG # noisy debug output from the dbri driver 645#options DBRI_BIG_BUFFER # use bigger DMA buffers, for slow CPUs 646dbri* at sbus? slot ? offset ? # SUNW,DBRI[s3|e] 647 648audio* at audiobus? 649 650## Sun "bwtwo" black and white framebuffer, found on sun4, sun4c, and sun4m 651## systems. If your sun4 system has a cgfour installed in the P4 slot, 652## the P4 entries for "bwtwo" will attach to the overlay plane of the 653## "cgfour". 654 655bwtwo0 at sbus0 slot ? offset ? # sun4c and sun4m 656bwtwo* at sbus? slot ? offset ? # 657bwtwo0 at obio0 addr 0xfd000000 level 4 # sun4/200 658bwtwo0 at obio0 addr 0xfb300000 level 4 # sun4/300 in P4 slot 659bwtwo0 at obio0 addr 0x0b300000 level 4 # sun4/100 in P4 slot 660 661## Sun "cgtwo" VME color framebuffer 662# XXX no wsdisplay support 663#cgtwo0 at vme0 addr 0x400000 irq ? vect 0xa8 664 665## Sun "cgthree" Sbus color framebuffer 666cgthree0 at sbus? slot ? offset ? 667cgthree* at sbus? slot ? offset ? 668#cgthree0 at obio? slot ? offset ? # sun4m 669 670## Sun "cgfour" color framebuffer with overlay plane. See above comment 671## regarding overlay plane. 672# XXX no wsdisplay support 673#cgfour0 at obio0 addr 0xfb300000 level 4 # sun4/300 P4 674#cgfour0 at obio0 addr 0x0b300000 level 4 # sun4/100 P4 675 676## Sun "cgsix" accelerated color framebuffer. 677cgsix0 at sbus? slot ? offset ? 678cgsix* at sbus? slot ? offset ? 679cgsix0 at obio0 addr 0xfb000000 level 4 # sun4/300 P4 680cgsix0 at obio0 addr 0x0b000000 level 4 # sun4/100 P4 681 682## Sun "cgeight" 24-bit framebuffer 683# XXX no wsdisplay support 684#cgeight0 at obio0 addr 0xfb300000 level 4 # sun4/300 P4 685#cgeight0 at obio0 addr 0x0b300000 level 4 # sun4/100 P4 686 687## Sun "tcx" accelerated color framebuffer. 688# XXX no wsdisplay support 689#tcx0 at sbus? slot ? offset ? 690#tcx* at sbus? slot ? offset ? 691 692# Sun "cgfourteen" accelerated 24-bit framebuffer. 693cgfourteen* at obio0 # sun4m 694 695# P9100-based display on Tadpole SPARCbook 3. 696pnozz0 at sbus? slot ? offset ? 697 698# Sun ZX/Leo 24-bit framebuffer 699# XXX no wsdisplay support 700#zx* at sbus? slot ? offset ? 701 702# Fujitsu AG-10e accelerated graphics 8/24-bit board 703agten* at sbus? slot ? offset ? 704 705# make sure wsdisplay0 is the console 706wsdisplay0 at wsemuldisplaydev? console 1 707wsdisplay* at wsemuldisplaydev? 708 709#### Other device configuration 710 711# Tadpole microcontroller 712tctrl0 at obio0 713 714## Pseudo ttys, required for network logins and programs like screen. 715 716pseudo-device pty # pseudo-terminals 717 718## Random device, used to implement /dev/random (a source of random noise), 719## and generate randomness for some kernel formulae. 720 721pseudo-device rnd 722 723# a pseudo device needed for Coda # also needs CODA (above) 724pseudo-device vcoda 4 # coda minicache <-> venus comm. 725 726pseudo-device clockctl # user control of clock subsystem 727pseudo-device ksyms # /dev/ksyms 728#pseudo-device pf # PF packet filter 729#pseudo-device pflog # PF log if 730pseudo-device fss 4 # file system snapshot device 731pseudo-device wsmux # mouse and keyboard multiplexor 732pseudo-device wsfont 733 734#options FILEASSOC # fileassoc(9) 735 736# Veriexec 737# 738# a pseudo device needed for veriexec 739#pseudo-device veriexec 1 740# 741# Uncomment the fingerprint methods below that are desired. Note that 742# removing fingerprint methods will have almost no impact on the kernel 743# code size. 744# 745#options VERIFIED_EXEC_FP_RMD160 746#options VERIFIED_EXEC_FP_SHA256 747#options VERIFIED_EXEC_FP_SHA384 748#options VERIFIED_EXEC_FP_SHA512 749#options VERIFIED_EXEC_FP_SHA1 750#options VERIFIED_EXEC_FP_MD5 751 752#options PAX_MPROTECT=0 # PaX mprotect(2) restrictions 753 # (for static binaries only for now) 754