GENERIC revision 1.221
1 # $NetBSD: GENERIC,v 1.221 2010/03/24 00:39:07 macallan Exp $ 2 # 3 # GENERIC machine description file 4 # 5 # This machine description file is used to generate the default NetBSD 6 # kernel. The generic kernel does not include all options, subsystems 7 # and device drivers, but should be useful for most applications. 8 # 9 # The machine description file can be customised for your specific 10 # machine to reduce the kernel size and improve its performance. 11 # 12 # For further information on compiling NetBSD kernels, see the config(8) 13 # man page. 14 # 15 # For further information on hardware support for this architecture, see 16 # the intro(4) man page. For further information about kernel options 17 # for this architecture, see the options(4) man page. For an explanation 18 # of each device driver in this file see the section 4 man page for the 19 # device. 20 21 include "arch/sparc/conf/std.sparc" 22 23 options INCLUDE_CONFIG_FILE # embed config file in kernel binary 24 25 #ident "GENERIC-$Revision: 1.221 $" 26 27 maxusers 32 28 29 ## System kernel configuration. See options(4) for more detail. 30 31 32 # Options for variants of the Sun SPARC architecure. 33 # We currently support three architecture types; at least one is required. 34 options SUN4 # sun4/100, sun4/200, sun4/300 35 options SUN4C # sun4c - SS1, 1+, 2, ELC, SLC, IPC, IPX, etc. 36 options SUN4M # sun4m - SS10, SS20, Classic, etc. 37 options SUN4D # sun4d - SS1000, SC2000 38 39 options SUN4_MMU3L # sun4/400 3-level MMU 40 41 ## System options specific to the sparc machine type 42 43 # Blink the power LED on some machines to indicate the system load. 44 #options BLINK 45 46 ## Use a faster console than the PROM's slow drawing routines. Not needed 47 ## for headless (no framebuffer) machines. 48 ## These is obsolete for wscons kernels 49 #options RASTERCONSOLE # fast rasterop console 50 #options RASTERCONSOLE_FGCOL=WSCOL_BLACK 51 #options RASTERCONSOLE_BGCOL=WSCOL_WHITE 52 53 # wscons stuff 54 options WSEMUL_SUN 55 #options WSEMUL_VT100 56 options WSDISPLAY_COMPAT_RAWKBD 57 options WSDISPLAY_CUSTOM_OUTPUT 58 options WS_DEFAULT_FG=WSCOL_BLACK 59 options WS_DEFAULT_BG=WSCOL_LIGHT_WHITE 60 options WS_KERNEL_FG=WSCOL_GREEN 61 options WS_KERNEL_BG=WSCOL_LIGHT_WHITE 62 options WSDISPLAY_COMPAT_PCVT 63 options WSDISPLAY_COMPAT_SYSCONS 64 options WSDISPLAY_COMPAT_USL 65 66 options WSDISPLAY_SCROLLSUPPORT 67 68 # generic options vlid for both wscons and RASTERCONSOLE 69 options FONT_GALLANT12x22 # the console font 70 #options FONT_BOLD8x16 # a somewhat smaller font 71 72 #### System options that are the same for all ports 73 74 ## Root device configuration: change the ?'s if you are going to use a 75 ## nonstandard root partition (other than where the kernel is booted from) 76 ## and/or nonstandard root type (not ffs or nfs). Normally this can be 77 ## automagically determined at boot time. 78 79 config netbsd root on ? type ? 80 81 ## System call tracing (see ktrace(1)). 82 options KTRACE 83 84 ## Collect statistics on kernel malloc's and free's. This does have a 85 ## significant performance hit on slower machines, so it is intended for 86 ## diagnostic use only. 87 #options KMEMSTATS 88 89 ## System V compatible IPC subsystem. (msgctl(2), semctl(2), and shmctl(2)) 90 options SYSVMSG # System V message queues 91 options SYSVSEM # System V semaphores 92 options SYSVSHM # System V shared memory 93 options P1003_1B_SEMAPHORE # p1003.1b semaphore support 94 95 ## Loadable kernel module support; still under development. 96 97 options USERCONF # userconf(4) support 98 #options PIPE_SOCKETPAIR # smaller, but slower pipe(2) 99 options SYSCTL_INCLUDE_DESCR # Include sysctl descriptions in kernel 100 101 # Enable experimental buffer queue strategy for better responsiveness under 102 # high disk I/O load. Use it with caution - it's not proven to be stable yet. 103 #options BUFQ_READPRIO 104 #options BUFQ_PRIOCSCAN 105 106 ## NFS boot options; tries DHCP/BOOTP then BOOTPARAM 107 options NFS_BOOT_BOOTPARAM 108 #options NFS_BOOT_BOOTP 109 options NFS_BOOT_DHCP 110 111 #### Debugging options 112 113 ## The DDB in-kernel debugger runs at panic (unless DDB_ONPANIC=0), or at 114 ## serial console break or keyboard reset, where the PROM would normally 115 ## intercept. DDB_HISTORY_SIZE adds up/down arrow command history. 116 options DDB # kernel dynamic debugger 117 options DDB_HISTORY_SIZE=100 # enable history editing in DDB 118 #options DDB_ONPANIC=1 # see also sysctl(8): `ddb.onpanic' 119 120 ## You may also use gdb, on another computer connected to this machine over 121 ## a serial port. Both KGDB_DEV and KGDB_DEVRATE should be specified; 122 ## KGDB_DEV is a dev_t encoded device number of the serial port to use, where 123 ## the minor device number encodes the PROM enumeration of the serial ports, 124 ## i.e.: 125 ## 0xc00 = ttya, 0xc01 = ttyb, 0xc02 = ttyc, 0xc03 = ttyd. 126 ## (Note: ttyc and ttyd are available only on some sun4 models) 127 #options KGDB # support for kernel gdb 128 #options KGDB_DEV=0xc01 # kgdb device number (this is `ttyb') 129 #options KGDB_DEVRATE=38400 # baud rate 130 131 132 ## Compile the kernel with debugging symbols (`netbsd.gdb' is the debug file), 133 ## such that gdb(1) can be used on a kernel coredump. 134 135 #makeoptions DEBUG="-g" 136 137 138 ## Adds code to the kernel that does internal consistency checks, and will 139 ## cause the kernel to panic if corruption of internal data structures 140 ## is detected. 141 #options DIAGNOSTIC # extra kernel sanity checking 142 143 ## Enable (possibly expensive) debugging code that may also display messages 144 ## on the system console 145 #options DEBUG 146 147 ## Make SCSI error messages more verbose when explaining their meanings. 148 options SCSIVERBOSE 149 150 options MIIVERBOSE # verbose PHY autoconfig messages 151 152 ## `INSECURE' turns off the kernel security level (securelevel = 0 always). 153 ## This allows writing to /dev/mem, loading kernel modules while multi-user, 154 ## and other insecurities good only for development work. Do not use this 155 ## option on a production machine. 156 #options INSECURE 157 158 ## `FDSCRIPTS' allows non-readable but executable scripts by providing a 159 ## pre-opened opaque file to the script interpreter. `SETUIDSCRIPTS', 160 ## which implies FDSCRIPTS, allows scripts to be set-user-id using the same 161 ## opaque file mechanism. Perl calls this "secure setuid scripts." 162 163 #options FDSCRIPTS 164 #options SETUIDSCRIPTS 165 166 ## Options for compatibility with previous releases foreign system binaries. 167 ## In the cases of COMPAT_SUNOS and COMPAT_SVR4, you may need to set up 168 ## additional user-level utilities or system configuration files. See 169 ## compat_sunos(8) and compat_svr4(8). 170 171 options COMPAT_43 # 4.3BSD system interfaces 172 options COMPAT_10 # NetBSD 1.0 binary compatibility 173 options COMPAT_11 # NetBSD 1.1 binary compatibility 174 options COMPAT_12 # NetBSD 1.2 binary compatibility 175 options COMPAT_13 # NetBSD 1.3 binary compatibility 176 options COMPAT_14 # NetBSD 1.4 binary compatibility 177 options COMPAT_15 # NetBSD 1.5 binary compatibility 178 options COMPAT_16 # NetBSD 1.6 binary compatibility 179 options COMPAT_20 # NetBSD 2.0 binary compatibility 180 options COMPAT_30 # NetBSD 3.0 binary compatibility 181 options COMPAT_40 # NetBSD 4.0 binary compatibility 182 options COMPAT_50 # NetBSD 5.0 binary compatibility 183 options COMPAT_SUNOS # SunOS 4.x binary compatibility 184 options COMPAT_SVR4 # SunOS 5.x binary compatibility 185 options COMPAT_BSDPTY # /dev/[pt]ty?? ptys. 186 187 ## File systems. You probably need at least one of FFS or NFS. 188 file-system FFS # Berkeley Fast Filesystem 189 file-system NFS # Sun NFS-compatible filesystem client 190 file-system KERNFS # kernel data-structure filesystem 191 file-system NULLFS # NULL layered filesystem 192 file-system OVERLAY # overlay file system 193 file-system MFS # memory-based filesystem 194 file-system FDESC # user file descriptor filesystem 195 file-system UMAPFS # uid/gid remapping filesystem 196 file-system LFS # Log-based filesystem (still experimental) 197 file-system PUFFS # Userspace file systems (e.g. ntfs-3g & sshfs) 198 file-system PROCFS # /proc 199 file-system CD9660 # ISO 9660 + Rock Ridge file system 200 file-system UNION # union file system 201 file-system MSDOSFS # MS-DOS FAT filesystem(s). 202 file-system CODA # Coda File System; also needs vcoda (below) 203 file-system PTYFS # /dev/pts/N support 204 #file-system TMPFS # Efficient memory file-system 205 #file-system UDF # experimental - OSTA UDF CD/DVD file-system 206 207 ## File system options. 208 options NFSSERVER # Sun NFS-compatible filesystem server 209 options QUOTA # FFS quotas 210 #options FFS_EI # FFS Endian Independent support 211 options WAPBL # File system journaling support - Experimental 212 #options UFS_DIRHASH # UFS Large Directory Hashing - Experimental 213 #options FFS_NO_SNAPSHOT # No FFS snapshot support 214 215 ## Network protocol support. In most environments, INET is required. 216 options INET # IP (Internet Protocol) v4 217 options INET6 # IPV6 218 #options IPSEC # IP security 219 #options IPSEC_ESP # IP security (encryption part; define w/IPSEC) 220 #options IPSEC_NAT_T # IPsec NAT traversal (NAT-T) 221 #options IPSEC_DEBUG # debug for IP security 222 #options GATEWAY # packet forwarding ("router switch") 223 #options MROUTING # packet forwarding of multicast packets 224 #options PIM # Protocol Independent Multicast 225 #options DIRECTED_BROADCAST # allow broadcasts through routers 226 #options ISO,TPIP # OSI networking 227 #options EON # OSI tunneling over IP 228 #options NETATALK # AppleTalk (over Ethernet) protocol 229 options NTP # Network Time Protocol in-kernel support 230 #options PPS_SYNC # Add serial line synchronization for NTP 231 options PFIL_HOOKS # Add pfil(9) hooks, intended for custom LKMs. 232 options IPFILTER_LOG # Add ipmon(8) logging for ipfilter device 233 options IPFILTER_LOOKUP # ippool(8) support 234 #options IPFILTER_DEFAULT_BLOCK # block all packets by default 235 options PPP_BSDCOMP # Add BSD compression to ppp device 236 options PPP_DEFLATE # Add deflate (libz) compression to ppp device 237 options PPP_FILTER # Add active filters for ppp (via bpf) 238 239 #options ALTQ # Manipulate network interfaces' output queues 240 #options ALTQ_BLUE # Stochastic Fair Blue 241 #options ALTQ_CBQ # Class-Based Queueing 242 #options ALTQ_CDNR # Diffserv Traffic Conditioner 243 #options ALTQ_FIFOQ # First-In First-Out Queue 244 #options ALTQ_FLOWVALVE # RED/flow-valve (red-penalty-box) 245 #options ALTQ_HFSC # Hierarchical Fair Service Curve 246 #options ALTQ_LOCALQ # Local queueing discipline 247 #options ALTQ_PRIQ # Priority Queueing 248 #options ALTQ_RED # Random Early Detection 249 #options ALTQ_RIO # RED with IN/OUT 250 #options ALTQ_WFQ # Weighted Fair Queueing 251 252 253 254 #### Main bus and CPU .. all systems. 255 mainbus0 at root 256 cpu0 at mainbus0 257 cpuunit0 at mainbus0 # sun4d 258 cpuunit* at mainbus0 # sun4d 259 cpu0 at cpuunit0 # sun4d 260 261 #### Bus types found on SPARC systems. 262 263 sbus0 at mainbus0 # sun4c 264 obio0 at mainbus0 # sun4 and sun4m 265 sparcvme0 at mainbus0 # sun4 266 iommu0 at mainbus0 # sun4m 267 sbus0 at iommu0 # sun4m 268 sparcvme0 at iommu0 # sun4m 269 vme0 at sparcvme0 # MI VME attachment 270 bootbus0 at cpuunit0 # sun4d 271 bootbus* at cpuunit? # sun4d 272 273 ## SBus expander box 274 xbox* at sbus? slot ? offset ? 275 sbus* at xbox? 276 277 ## SBus to PCMCIA bridge 278 nell* at sbus? slot ? offset ? # PCMCIA bridge 279 pcmcia* at nell? 280 tslot* at sbus? slot ? offset ? # PCMCIA bridge (tadpole 3gx) 281 pcmcia* at tslot? 282 283 #### Standard system devices -- all required for a given architecture 284 285 ## Auxiliary system registers on sun4c and sun4m 286 auxreg0 at mainbus0 # sun4c 287 auxreg0 at obio0 # sun4m 288 auxiotwo0 at obio0 # only on Tadpole SPARCbook. 289 290 ## Power status and control register on Sun4m systems 291 power0 at obio0 292 293 ## Mostek clock found on 4/300, sun4c, sun4m and sun4d systems. 294 ## The Mostek clock NVRAM is the "eeprom" on sun4/300 systems. 295 clock0 at mainbus0 # sun4c 296 clock0 at obio0 # sun4m 297 clock0 at obio0 addr 0xf2000000 # sun4/300 298 clock0 at bootbus0 # sun4d 299 300 ## Intersil clock found on 4/100 and 4/200 systems. 301 oclock0 at obio0 addr 0xf3000000 # sun4/200 302 oclock0 at obio0 addr 0x03000000 # sun4/100 303 304 ## Memory error registers. 305 memreg0 at mainbus0 # sun4c 306 memreg0 at obio0 # sun4m 307 memreg0 at obio0 addr 0xf4000000 # sun4/200 and sun4/300 308 memreg0 at obio0 addr 0x04000000 # sun4/100 309 310 ## ECC memory control 311 eccmemctl0 at mainbus0 # sun4m 312 313 ## Timer chip found on 4/300, sun4c, and sun4m systems. 314 timer0 at mainbus0 # sun4c 315 timer0 at obio0 # sun4m 316 timer0 at obio0 addr 0xef000000 # sun4/300 317 318 ## EEPROM found on 4/100 and 4/200 systems. Note that the 4/300 319 ## doesn't use this driver; the `EEPROM' is in the NVRAM on the 320 ## Mostek clock chip on 4/300 systems. 321 eeprom0 at obio0 addr 0xf2000000 # sun4/200 322 eeprom0 at obio0 addr 0x02000000 # sun4/100 323 324 325 #### Serial port configuration 326 327 ## Zilog 8530 serial chips. Each has two-channels. 328 ## zs0 is ttya and ttyb. zs1 is the keyboard and mouse. 329 zs0 at mainbus0 # sun4c 330 zs0 at obio0 # sun4m 331 zs0 at obio0 addr 0xf1000000 level 12 # sun4/200 and sun4/300 332 zs0 at obio0 addr 0x01000000 level 12 # sun4/100 333 zs0 at bootbus0 # sun4d 334 zstty0 at zs0 channel 0 # ttya 335 zstty1 at zs0 channel 1 # ttyb 336 337 zs1 at mainbus0 # sun4c 338 zs1 at obio0 # sun4m 339 zs1 at obio0 addr 0xf0000000 level 12 # sun4/200 and sun4/300 340 zs1 at obio0 addr 0x00000000 level 12 # sun4/100 341 zs1 at bootbus0 # sun4d 342 343 # old kbd and mouse attachments 344 #kbd0 at zs1 channel 0 # keyboard 345 #ms0 at zs1 channel 1 # mouse 346 zstty* at zs? 347 348 # these are for wscons 349 kbd0 at zstty? 350 ms0 at zstty? 351 wskbd* at wskbddev? 352 wsmouse* at wsmousedev? 353 354 zs2 at obio0 addr 0xe0000000 level 12 # sun4/300 355 zstty2 at zs2 channel 0 # ttyc 356 zstty3 at zs2 channel 1 # ttyd 357 358 zs* at bootbus? # sun4d 359 zstty* at zs? 360 361 ## NS16x50 serial chips and clones. Present on the 362 ## Sun JavaStation-1 and Tadpole SPARCbook 3 363 com* at obio0 # sun4m 364 365 # Parallel port. 366 bpp* at sbus? slot? offset ? 367 368 ## Magma Serial/Parallel driver 369 magma* at sbus? slot ? offset ? 370 mtty* at magma? 371 mbpp* at magma? 372 373 ## SUNW,spif Serial/Parallel driver 374 spif* at sbus? slot ? offset ? 375 stty* at spif? 376 sbpp* at spif? 377 378 ## PCMCIA serial interfaces 379 #com* at pcmcia? 380 #pcmcom* at pcmcia? 381 #com* at pcmcom? 382 383 #### Disk controllers and disks 384 385 # 386 387 ## The following flags may be set for the NCR53c94 based esp driver: 388 ## bits 0-7: disable disconnect/reselect for the corresponding target 389 ## bits 8-15: disable synchronous negotiation for target [bit-8] 390 391 ## sun4/300, sun4c, sun4m on-board SCSI, and FSBE/S SBus SCSI cards. 392 ## Both `dma' and `esp' are needed in all cases. 393 ## Two kinds of additional SBus SCSI interfaces are available. One uses 394 ## "esp at sbus" like the sun4c on-board; the other uses "esp at dma". 395 396 ## sun4/300 SCSI - an NCR53c94 or equivalent behind 397 ## an LSI Logic DMA controller 398 399 dma0 at obio0 addr 0xfa001000 level 4 # sun4/300 400 esp0 at obio0 addr 0xfa000000 level 4 flags 0x0000 # sun4/300 401 402 dma0 at sbus0 slot ? offset ? # sun4c/sun4m 403 esp0 at sbus0 slot ? offset ? flags 0x0000 # sun4c 404 esp0 at dma0 flags 0x0000 # sun4m 405 406 # FSBE/S SCSI & SunSwift Sbus FAS366 407 dma* at sbus? slot ? offset ? # SBus 408 esp* at sbus? slot ? offset ? flags 0x0000 # SBus 409 esp* at dma? flags 0x0000 # SBus 410 411 scsibus* at esp? 412 413 ## Qlogic ISP SBus SCSI Card 414 isp* at sbus? slot ? offset ? 415 scsibus* at isp? 416 417 ## NCR5380-based "Sun SCSI 3" VME SCSI controller. 418 ## This driver has several flags which may be enabled by OR'ing 419 ## the values and using the "flags" directive. 420 ## Valid flags are: 421 ## 422 ## 0x01 Use DMA (may be polled) 423 ## 0x02 Use DMA completion interrupts 424 ## 0x04 Allow disconnect/reselect 425 ## 426 ## E.g. the following would enable DMA, interrupts, and reselect: 427 ## si0 at vme0 addr 0x200000 irq 3 vect 0x40 flags 0x07 428 ## 429 ## By default, DMA is enabled in the driver. 430 431 si0 at vme0 addr 0x200000 irq 2 vect 0x40 432 scsibus* at si? 433 434 ## NCR5380-based "SCSI Weird" on-board SCSI interface found 435 ## on sun4/100 systems. The flags are the same as the "si" 436 ## controller. Note, while DMA is enabled by default, only 437 ## polled DMA works at this time, and reselects do not work 438 ## on this particular controller. 439 440 sw0 at obio0 addr 0x0a000000 level 3 441 scsibus* at sw? 442 443 ## PCMCIA SCSI controllers 444 #aic* at pcmcia? 445 #spc* at pcmcia? 446 #scsibus* at aic? 447 #scsibus* at spc? 448 449 450 ## These entries find devices on all SCSI busses and assign 451 ## unit numbers dynamically. 452 sd* at scsibus? target ? lun ? # SCSI disks 453 st* at scsibus? target ? lun ? # SCSI tapes 454 cd* at scsibus? target ? lun ? # SCSI CD-ROMs 455 ch* at scsibus? target ? lun ? # SCSI changer devices 456 ss* at scsibus? target ? lun ? # SCSI scanners 457 ses* at scsibus? target ? lun ? # SCSI SES/SAF-TE 458 uk* at scsibus? target ? lun ? # unknown SCSI 459 460 461 ## Xylogics 753 or 7053 VME SMD disk controllers and disks, found 462 ## on sun4 systems. 463 xdc0 at vme0 addr 0xee80 irq 3 vect 0x44 464 xdc1 at vme0 addr 0xee90 irq 3 vect 0x45 465 xdc2 at vme0 addr 0xeea0 irq 3 vect 0x46 466 xdc3 at vme0 addr 0xeeb0 irq 3 vect 0x47 467 xd* at xdc? drive ? 468 469 ## Xylogics 451 or 451 VME SMD disk controllers and disks, found 470 ## on sun4 systems. 471 xyc0 at vme0 addr 0xee40 irq 3 vect 0x48 472 xyc1 at vme0 addr 0xee48 irq 3 vect 0x49 473 xy* at xyc? drive ? 474 475 476 ## Floppy controller and drive found on SPARCstations. 477 478 fdc0 at mainbus0 # sun4c controller 479 fdc0 at obio0 # sun4m controller 480 fd* at fdc0 # the drive itself 481 482 ## PCMCIA IDE controllers 483 #wdc* at pcmcia? 484 #atabus* at ata? 485 #wd* at atabus? drive ? flags 0x0000 486 487 ## A disk-like interface to files. Can be used to create floppy, CD, 488 ## miniroot images, etc. 489 490 pseudo-device vnd 491 #options VND_COMPRESSION # compressed vnd(4) 492 493 ## Concatenated and striped disks; with this, you can create a software-based 494 ## disk array similar to a "RAID 0" setup. See ccd(4). 495 496 pseudo-device ccd 4 497 498 ## Cryptographic disk devices; See cgd(4) 499 500 #pseudo-device cgd 4 501 502 ## RAIDframe disk driver: software RAID driver. See raid(4). 503 504 pseudo-device raid 8 505 options RAID_AUTOCONFIG # auto-configuration of RAID components 506 # Options to enable various other RAIDframe RAID types. 507 # options RF_INCLUDE_EVENODD=1 508 # options RF_INCLUDE_RAID5_RS=1 509 # options RF_INCLUDE_PARITYLOGGING=1 510 # options RF_INCLUDE_CHAINDECLUSTER=1 511 # options RF_INCLUDE_INTERDECLUSTER=1 512 # options RF_INCLUDE_PARITY_DECLUSTERING=1 513 # options RF_INCLUDE_PARITY_DECLUSTERING_DS=1 514 515 516 ## Memory disk device, used on boot floppies with compressed 517 ## kernel-plus-root-disk images. 518 519 #pseudo-device md 1 520 521 522 #### Network interfaces 523 524 ## LANCE Ethernet - an AMD 7990 LANCE behind specialized DMA glue 525 ## Three flavors of additional SBus ethernets are available. One attaches 526 ## directly like the sun4c on-board, one uses the ledma device like the 527 ## sun4m on-board, and one uses the lebuffer device. 528 529 le0 at obio0 addr 0xf9000000 level 6 # sun4/300 530 le0 at sbus0 slot ? offset ? # sun4c on-board 531 ledma0 at sbus0 slot ? offset ? # sun4m on-board 532 le0 at ledma0 # sun4m on-board 533 le* at sbus? slot ? offset ? # SBus 534 ledma* at sbus? slot ? offset ? # SBus 535 le* at ledma? # SBus 536 lebuffer0 at sbus? slot ? offset ? # SBus 537 le0 at lebuffer? # SBus 538 lebuffer* at sbus? slot ? offset ? # SBus 539 le* at lebuffer? # SBus 540 541 542 ## sun4/100 and sun4/200 Ethernet - an Intel 82586 on-board 543 ## or on a Multibus/VME card. 544 ie0 at obio0 addr 0xf6000000 level 6 # sun4/200 on-board 545 ie0 at obio0 addr 0x06000000 level 6 # sun4/100 on-board 546 ## VME: the first [addr,len] pair specifies the device registers; 547 ## the second pair specifies the on-board memory buffer 548 ie1 at vme0 addr 0xe88000,0xe00000 len -1,0x40000 irq 3 vect 0x75 549 ie2 at vme0 addr 0x31ff02,0x300000 len -1,0x40000 irq 3 vect 0x76 550 ie3 at vme0 addr 0x35ff02,0x300000 len -1,0x40000 irq 3 vect 0x77 551 ie4 at vme0 addr 0x2dff02,0x200000 len -1,0x40000 irq 3 vect 0x7c 552 553 ## Quad Ethernet Controller with BigMac (be, 10/100MBd) and Mace Ethernet 554 ## (qe, 10MBd) attached. 555 qec* at sbus? slot ? offset ? # Quad Ethernet Controller 556 be* at qec? # BigMac Ethernet (10/100MBd) 557 qe* at qec? # Mace Ethernet (10MBd) 558 559 ## Happy Meal Ethernet 560 hme* at sbus? slot ? offset ? 561 562 # midway ATM 563 en0 at sbus? slot ? offset ? 564 565 # PCMCIA ethernet devices 566 #ep* at pcmcia? 567 #mbe* at pcmcia? 568 #ne* at pcmcia? 569 #sm* at pcmcia? 570 571 ## PCMCIA wavelan card 572 #wi* at pcmcia? function ? # Lucent WaveLan IEEE (802.11) 573 574 # MII/PHY support 575 exphy* at mii? phy ? # 3Com internal PHYs 576 icsphy* at mii? phy ? # Integrated Circuit Systems ICS189x 577 inphy* at mii? phy ? # Intel 82555 PHYs 578 lxtphy* at mii? phy ? # Level One LXT-970 PHYs 579 nsphy* at mii? phy ? # NS83840 PHYs 580 qsphy* at mii? phy ? # Quality Semiconductor QS6612 PHYs 581 sqphy* at mii? phy ? # Seeq 80220/80221/80223 PHYs 582 tlphy* at mii? phy ? # ThunderLAN PHYs 583 ukphy* at mii? phy ? # generic unknown PHYs 584 585 ## Loopback network interface; required 586 pseudo-device loop 587 588 ## SLIP and CSLIP interfaces, for IP over a serial line. 589 pseudo-device sl 590 591 ## PPP, the successor to SLIP. See pppd(8). 592 pseudo-device ppp 593 594 ## PPP over Ethernet (RFC 2516) 595 pseudo-device pppoe 596 597 ## Starmode Radio IP, a special hardware network device. 598 #pseudo-device strip 599 600 ## Network "tunnel" device, allowing protocol stacks to run in the userland. 601 ## This is used by the third-party user-mode "ppp" program, and others. 602 pseudo-device tun 603 pseudo-device tap # virtual Ethernet 604 605 ## Generic L3 over IP tunnel 606 #pseudo-device gre # generic L3 over IP tunnel 607 608 ## Berkeley Packet Filter, required to run RARPD. A generic C-language 609 ## interface that allows selective examining of incoming packets. 610 pseudo-device bpfilter 611 612 #pseudo-device carp # Common Address Redundancy Protocol 613 614 ## IP Filter, used in firewall and NAT applications. See ipnat(8) for 615 ## one example of the use of the IP Filter. 616 pseudo-device ipfilter 617 618 ## for IPv6 619 pseudo-device gif # IPv[46] over IPv[46] tunnel (RFC1933) 620 #pseudo-device faith # IPv[46] tcp relay translation i/f 621 pseudo-device stf # 6to4 IPv6 over IPv4 encapsulation 622 623 ## IEEE 802.1Q Virtual LAN encapsulation, see vlan(4). 624 pseudo-device vlan 625 626 ## Simple inter-network traffic bridging 627 pseudo-device bridge 628 #options BRIDGE_IPF # bridge uses IP/IPv6 pfil hooks too 629 pseudo-device agr # IEEE 802.3ad link aggregation 630 631 ## accept filters 632 pseudo-device accf_data # "dataready" accept filter 633 pseudo-device accf_http # "httpready" accept filter 634 635 #### Audio and video devices 636 637 ## /dev/audio support (`audioamd' plus `audio') 638 ## 639 audioamd0 at mainbus0 # sun4c 640 audioamd0 at obio0 # sun4m 641 audioamd0 at sbus0 slot ? offset ? # sun4m 642 643 audiocs0 at sbus0 slot ? offset ? # SUNW,CS4231 644 645 #options DBRI_DEBUG # noisy debug output from the dbri driver 646 #options DBRI_BIG_BUFFER # use bigger DMA buffers, for slow CPUs 647 dbri* at sbus? slot ? offset ? # SUNW,DBRI[s3|e] 648 649 audio* at audiobus? 650 651 ## Sun "bwtwo" black and white framebuffer, found on sun4, sun4c, and sun4m 652 ## systems. If your sun4 system has a cgfour installed in the P4 slot, 653 ## the P4 entries for "bwtwo" will attach to the overlay plane of the 654 ## "cgfour". 655 656 bwtwo0 at sbus0 slot ? offset ? # sun4c and sun4m 657 bwtwo* at sbus? slot ? offset ? # 658 bwtwo0 at obio0 addr 0xfd000000 level 4 # sun4/200 659 bwtwo0 at obio0 addr 0xfb300000 level 4 # sun4/300 in P4 slot 660 bwtwo0 at obio0 addr 0x0b300000 level 4 # sun4/100 in P4 slot 661 662 ## Sun "cgtwo" VME color framebuffer 663 # XXX no wsdisplay support 664 #cgtwo0 at vme0 addr 0x400000 irq ? vect 0xa8 665 666 ## Sun "cgthree" Sbus color framebuffer 667 cgthree0 at sbus? slot ? offset ? 668 cgthree* at sbus? slot ? offset ? 669 670 ## Sun "cgfour" color framebuffer with overlay plane. See above comment 671 ## regarding overlay plane. 672 # XXX no wsdisplay support 673 #cgfour0 at obio0 addr 0xfb300000 level 4 # sun4/300 P4 674 #cgfour0 at obio0 addr 0x0b300000 level 4 # sun4/100 P4 675 676 ## Sun "cgsix" accelerated color framebuffer. 677 cgsix0 at sbus? slot ? offset ? 678 cgsix* at sbus? slot ? offset ? 679 cgsix0 at obio0 addr 0xfb000000 level 4 # sun4/300 P4 680 cgsix0 at obio0 addr 0x0b000000 level 4 # sun4/100 P4 681 682 ## Sun "cgeight" 24-bit framebuffer 683 # XXX no wsdisplay support 684 #cgeight0 at obio0 addr 0xfb300000 level 4 # sun4/300 P4 685 #cgeight0 at obio0 addr 0x0b300000 level 4 # sun4/100 P4 686 687 ## Sun "tcx" accelerated color framebuffer. 688 # there can be only one 689 tcx0 at sbus? slot ? offset ? 690 691 ## Sun CG12 / Matrox SG3 accelerated 24bit framebuffer 692 ## runs monochrome only for now 693 cgtwelve* at sbus? slot ? offset ? 694 695 # Sun "cgfourteen" accelerated 24-bit framebuffer. 696 cgfourteen* at obio0 # sun4m 697 698 # P9100-based display on Tadpole SPARCbook 3. 699 pnozz0 at sbus? slot ? offset ? 700 # the SPARCbook 3 hardware docs say that accesses to P9100 registers need to be 701 # 'latched in' but at least my 3GX works happily without 702 # Enable it by default since we don't know which hardware really needs it. 703 options PNOZZ_USE_LATCH 704 705 # Sun ZX/Leo 24-bit framebuffer 706 zx* at sbus? slot ? offset ? 707 708 # Fujitsu AG-10e accelerated graphics 8/24-bit board 709 agten* at sbus? slot ? offset ? 710 711 # generic framebuffer console 712 genfb* at sbus? slot ? offset ? 713 714 # make sure wsdisplay0 is the console 715 wsdisplay0 at wsemuldisplaydev? console 1 716 wsdisplay* at wsemuldisplaydev? 717 718 #### Other device configuration 719 720 # Tadpole microcontroller 721 tctrl0 at obio0 722 723 # Aurora Personality Chip (APC) on SPARCstation-4/5 724 # Not enabled by default as it may hang some systems 725 #apc* at sbus? slot ? offset ? 726 727 ## Pseudo ttys, required for network logins and programs like screen. 728 729 pseudo-device pty # pseudo-terminals 730 731 ## Random device, used to implement /dev/random (a source of random noise), 732 ## and generate randomness for some kernel formulae. 733 734 pseudo-device rnd 735 736 # a pseudo device needed for Coda # also needs CODA (above) 737 pseudo-device vcoda 4 # coda minicache <-> venus comm. 738 739 pseudo-device clockctl # user control of clock subsystem 740 pseudo-device ksyms # /dev/ksyms 741 #pseudo-device pf # PF packet filter 742 #pseudo-device pflog # PF log if 743 pseudo-device fss 4 # file system snapshot device 744 pseudo-device wsmux # mouse and keyboard multiplexor 745 pseudo-device wsfont 746 pseudo-device putter # for puffs and pud 747 748 #options FILEASSOC # fileassoc(9) 749 750 # Veriexec 751 # 752 # a pseudo device needed for veriexec 753 #pseudo-device veriexec 1 754 # 755 # Uncomment the fingerprint methods below that are desired. Note that 756 # removing fingerprint methods will have almost no impact on the kernel 757 # code size. 758 # 759 #options VERIFIED_EXEC_FP_RMD160 760 #options VERIFIED_EXEC_FP_SHA256 761 #options VERIFIED_EXEC_FP_SHA384 762 #options VERIFIED_EXEC_FP_SHA512 763 #options VERIFIED_EXEC_FP_SHA1 764 #options VERIFIED_EXEC_FP_MD5 765 766 #options PAX_MPROTECT=0 # PaX mprotect(2) restrictions 767 # (for static binaries only for now) 768
Indexes created Wed Oct 01 07:09:59 GMT 2025