GENERIC revision 1.230
1 # $NetBSD: GENERIC,v 1.230 2012/01/11 17:18:51 macallan Exp $ 2 # 3 # GENERIC machine description file 4 # 5 # This machine description file is used to generate the default NetBSD 6 # kernel. The generic kernel does not include all options, subsystems 7 # and device drivers, but should be useful for most applications. 8 # 9 # The machine description file can be customised for your specific 10 # machine to reduce the kernel size and improve its performance. 11 # 12 # For further information on compiling NetBSD kernels, see the config(8) 13 # man page. 14 # 15 # For further information on hardware support for this architecture, see 16 # the intro(4) man page. For further information about kernel options 17 # for this architecture, see the options(4) man page. For an explanation 18 # of each device driver in this file see the section 4 man page for the 19 # device. 20 21 include "arch/sparc/conf/std.sparc" 22 23 options INCLUDE_CONFIG_FILE # embed config file in kernel binary 24 25 #ident "GENERIC-$Revision: 1.230 $" 26 27 maxusers 32 28 29 ## System kernel configuration. See options(4) for more detail. 30 31 32 # Options for variants of the Sun SPARC architecure. 33 # We currently support three architecture types; at least one is required. 34 options SUN4 # sun4/100, sun4/200, sun4/300 35 options SUN4C # sun4c - SS1, 1+, 2, ELC, SLC, IPC, IPX, etc. 36 options SUN4M # sun4m - SS10, SS20, Classic, etc. 37 options SUN4D # sun4d - SS1000, SC2000 38 39 options SUN4_MMU3L # sun4/400 3-level MMU 40 41 ## System options specific to the sparc machine type 42 43 # Blink the power LED on some machines to indicate the system load. 44 #options BLINK 45 46 ## Use a faster console than the PROM's slow drawing routines. Not needed 47 ## for headless (no framebuffer) machines. 48 ## These is obsolete for wscons kernels 49 #options RASTERCONSOLE # fast rasterop console 50 #options RASTERCONSOLE_FGCOL=WSCOL_BLACK 51 #options RASTERCONSOLE_BGCOL=WSCOL_WHITE 52 53 # wscons stuff 54 options WSEMUL_SUN 55 #options WSEMUL_VT100 56 options WSDISPLAY_COMPAT_RAWKBD 57 options WSDISPLAY_CUSTOM_OUTPUT 58 options WS_DEFAULT_FG=WSCOL_BLACK 59 options WS_DEFAULT_BG=WSCOL_LIGHT_WHITE 60 options WS_KERNEL_FG=WSCOL_GREEN 61 options WS_KERNEL_BG=WSCOL_LIGHT_WHITE 62 options WSDISPLAY_COMPAT_PCVT 63 options WSDISPLAY_COMPAT_SYSCONS 64 options WSDISPLAY_COMPAT_USL 65 66 options WSDISPLAY_SCROLLSUPPORT 67 68 # generic options vlid for both wscons and RASTERCONSOLE 69 options FONT_GALLANT12x22 # the console font 70 options FONT_BOLD8x16 # a somewhat smaller font 71 72 #### System options that are the same for all ports 73 74 ## Root device configuration: change the ?'s if you are going to use a 75 ## nonstandard root partition (other than where the kernel is booted from) 76 ## and/or nonstandard root type (not ffs or nfs). Normally this can be 77 ## automagically determined at boot time. 78 79 config netbsd root on ? type ? 80 81 ## System call tracing (see ktrace(1)). 82 options KTRACE 83 84 ## Collect statistics on kernel malloc's and free's. This does have a 85 ## significant performance hit on slower machines, so it is intended for 86 ## diagnostic use only. 87 #options KMEMSTATS 88 89 ## System V compatible IPC subsystem. (msgctl(2), semctl(2), and shmctl(2)) 90 options SYSVMSG # System V message queues 91 options SYSVSEM # System V semaphores 92 options SYSVSHM # System V shared memory 93 options P1003_1B_SEMAPHORE # p1003.1b semaphore support 94 95 options MODULAR # new style module(7) framework 96 97 options USERCONF # userconf(4) support 98 #options PIPE_SOCKETPAIR # smaller, but slower pipe(2) 99 options SYSCTL_INCLUDE_DESCR # Include sysctl descriptions in kernel 100 101 # Enable experimental buffer queue strategy for better responsiveness under 102 # high disk I/O load. Use it with caution - it's not proven to be stable yet. 103 #options BUFQ_READPRIO 104 #options BUFQ_PRIOCSCAN 105 106 ## NFS boot options; tries DHCP/BOOTP then BOOTPARAM 107 options NFS_BOOT_BOOTPARAM 108 #options NFS_BOOT_BOOTP 109 options NFS_BOOT_DHCP 110 111 #### Debugging options 112 113 ## The DDB in-kernel debugger runs at panic (unless DDB_ONPANIC=0), or at 114 ## serial console break or keyboard reset, where the PROM would normally 115 ## intercept. DDB_HISTORY_SIZE adds up/down arrow command history. 116 options DDB # kernel dynamic debugger 117 options DDB_HISTORY_SIZE=100 # enable history editing in DDB 118 #options DDB_ONPANIC=1 # see also sysctl(8): `ddb.onpanic' 119 120 ## You may also use gdb, on another computer connected to this machine over 121 ## a serial port. Both KGDB_DEV and KGDB_DEVRATE should be specified; 122 ## KGDB_DEV is a dev_t encoded device number of the serial port to use, where 123 ## the minor device number encodes the PROM enumeration of the serial ports, 124 ## i.e.: 125 ## 0xc00 = ttya, 0xc01 = ttyb, 0xc02 = ttyc, 0xc03 = ttyd. 126 ## (Note: ttyc and ttyd are available only on some sun4 models) 127 #options KGDB # support for kernel gdb 128 #options KGDB_DEV=0xc01 # kgdb device number (this is `ttyb') 129 #options KGDB_DEVRATE=38400 # baud rate 130 131 132 ## Compile the kernel with debugging symbols (`netbsd.gdb' is the debug file), 133 ## such that gdb(1) can be used on a kernel coredump. 134 135 #makeoptions DEBUG="-g" 136 137 138 ## Adds code to the kernel that does internal consistency checks, and will 139 ## cause the kernel to panic if corruption of internal data structures 140 ## is detected. 141 #options DIAGNOSTIC # extra kernel sanity checking 142 143 ## Enable (possibly expensive) debugging code that may also display messages 144 ## on the system console 145 #options DEBUG 146 #options LOCKDEBUG 147 #options SYSCALL_DEBUG 148 149 ## Make SCSI error messages more verbose when explaining their meanings. 150 options SCSIVERBOSE 151 152 options MIIVERBOSE # verbose PHY autoconfig messages 153 154 ## `INSECURE' turns off the kernel security level (securelevel = 0 always). 155 ## This allows writing to /dev/mem, loading kernel modules while multi-user, 156 ## and other insecurities good only for development work. Do not use this 157 ## option on a production machine. 158 #options INSECURE 159 160 ## `FDSCRIPTS' allows non-readable but executable scripts by providing a 161 ## pre-opened opaque file to the script interpreter. `SETUIDSCRIPTS', 162 ## which implies FDSCRIPTS, allows scripts to be set-user-id using the same 163 ## opaque file mechanism. Perl calls this "secure setuid scripts." 164 165 #options FDSCRIPTS 166 #options SETUIDSCRIPTS 167 168 ## Options for compatibility with previous releases foreign system binaries. 169 ## In the cases of COMPAT_SUNOS and COMPAT_SVR4, you may need to set up 170 ## additional user-level utilities or system configuration files. See 171 ## compat_sunos(8) and compat_svr4(8). 172 173 options COMPAT_43 # 4.3BSD system interfaces 174 options COMPAT_10 # NetBSD 1.0 binary compatibility 175 options COMPAT_11 # NetBSD 1.1 binary compatibility 176 options COMPAT_12 # NetBSD 1.2 binary compatibility 177 options COMPAT_13 # NetBSD 1.3 binary compatibility 178 options COMPAT_14 # NetBSD 1.4 binary compatibility 179 options COMPAT_15 # NetBSD 1.5 binary compatibility 180 options COMPAT_16 # NetBSD 1.6 binary compatibility 181 options COMPAT_20 # NetBSD 2.0 binary compatibility 182 options COMPAT_30 # NetBSD 3.0 binary compatibility 183 options COMPAT_40 # NetBSD 4.0 binary compatibility 184 options COMPAT_50 # NetBSD 5.0 binary compatibility 185 options COMPAT_SUNOS # SunOS 4.x binary compatibility 186 options COMPAT_SVR4 # SunOS 5.x binary compatibility 187 options COMPAT_BSDPTY # /dev/[pt]ty?? ptys. 188 189 ## File systems. You probably need at least one of FFS or NFS. 190 file-system FFS # Berkeley Fast Filesystem 191 file-system NFS # Sun NFS-compatible filesystem client 192 file-system KERNFS # kernel data-structure filesystem 193 file-system NULLFS # NULL layered filesystem 194 file-system OVERLAY # overlay file system 195 file-system MFS # memory-based filesystem 196 file-system FDESC # user file descriptor filesystem 197 file-system UMAPFS # uid/gid remapping filesystem 198 file-system LFS # Log-based filesystem (still experimental) 199 file-system PUFFS # Userspace file systems (e.g. ntfs-3g & sshfs) 200 file-system PROCFS # /proc 201 file-system CD9660 # ISO 9660 + Rock Ridge file system 202 file-system UNION # union file system 203 file-system MSDOSFS # MS-DOS FAT filesystem(s). 204 file-system CODA # Coda File System; also needs vcoda (below) 205 file-system PTYFS # /dev/pts/N support 206 file-system TMPFS # Efficient memory file-system 207 #file-system UDF # experimental - OSTA UDF CD/DVD file-system 208 209 ## File system options. 210 options NFSSERVER # Sun NFS-compatible filesystem server 211 options QUOTA # FFS quotas 212 #options FFS_EI # FFS Endian Independent support 213 options WAPBL # File system journaling support 214 #options UFS_DIRHASH # UFS Large Directory Hashing - Experimental 215 #options FFS_NO_SNAPSHOT # No FFS snapshot support 216 217 ## Network protocol support. In most environments, INET is required. 218 options INET # IP (Internet Protocol) v4 219 options INET6 # IPV6 220 #options IPSEC # IP security 221 #options IPSEC_ESP # IP security (encryption part; define w/IPSEC) 222 #options IPSEC_NAT_T # IPsec NAT traversal (NAT-T) 223 #options IPSEC_DEBUG # debug for IP security 224 #options GATEWAY # packet forwarding ("router switch") 225 #options MROUTING # packet forwarding of multicast packets 226 #options PIM # Protocol Independent Multicast 227 #options DIRECTED_BROADCAST # allow broadcasts through routers 228 #options ISO,TPIP # OSI networking 229 #options EON # OSI tunneling over IP 230 #options NETATALK # AppleTalk (over Ethernet) protocol 231 options NTP # Network Time Protocol in-kernel support 232 #options PPS_SYNC # Add serial line synchronization for NTP 233 options PFIL_HOOKS # Add pfil(9) hooks, intended for custom LKMs. 234 options IPFILTER_LOG # Add ipmon(8) logging for ipfilter device 235 options IPFILTER_LOOKUP # ippool(8) support 236 options IPFILTER_COMPAT # Compat for IP-Filter 237 #options IPFILTER_DEFAULT_BLOCK # block all packets by default 238 options PPP_BSDCOMP # Add BSD compression to ppp device 239 options PPP_DEFLATE # Add deflate (libz) compression to ppp device 240 options PPP_FILTER # Add active filters for ppp (via bpf) 241 242 #options ALTQ # Manipulate network interfaces' output queues 243 #options ALTQ_BLUE # Stochastic Fair Blue 244 #options ALTQ_CBQ # Class-Based Queueing 245 #options ALTQ_CDNR # Diffserv Traffic Conditioner 246 #options ALTQ_FIFOQ # First-In First-Out Queue 247 #options ALTQ_FLOWVALVE # RED/flow-valve (red-penalty-box) 248 #options ALTQ_HFSC # Hierarchical Fair Service Curve 249 #options ALTQ_LOCALQ # Local queueing discipline 250 #options ALTQ_PRIQ # Priority Queueing 251 #options ALTQ_RED # Random Early Detection 252 #options ALTQ_RIO # RED with IN/OUT 253 #options ALTQ_WFQ # Weighted Fair Queueing 254 255 256 257 #### Main bus and CPU .. all systems. 258 mainbus0 at root 259 cpu0 at mainbus0 260 cpuunit0 at mainbus0 # sun4d 261 cpuunit* at mainbus0 # sun4d 262 cpu0 at cpuunit0 # sun4d 263 264 #### Bus types found on SPARC systems. 265 266 sbus0 at mainbus0 # sun4c 267 obio0 at mainbus0 # sun4 and sun4m 268 sparcvme0 at mainbus0 # sun4 269 iommu0 at mainbus0 # sun4m 270 sbus0 at iommu0 # sun4m 271 sparcvme0 at iommu0 # sun4m 272 vme0 at sparcvme0 # MI VME attachment 273 bootbus0 at cpuunit0 # sun4d 274 bootbus* at cpuunit? # sun4d 275 276 ## SBus expander box 277 xbox* at sbus? slot ? offset ? 278 sbus* at xbox? 279 280 ## SBus to PCMCIA bridge 281 nell* at sbus? slot ? offset ? # PCMCIA bridge 282 pcmcia* at nell? 283 tslot* at sbus? slot ? offset ? # PCMCIA bridge (tadpole 3gx) 284 pcmcia* at tslot? 285 286 #### Standard system devices -- all required for a given architecture 287 288 ## Auxiliary system registers on sun4c and sun4m 289 auxreg0 at mainbus0 # sun4c 290 auxreg0 at obio0 # sun4m 291 auxiotwo0 at obio0 # only on Tadpole SPARCbook. 292 293 ## Power status and control register on Sun4m systems 294 power0 at obio0 295 296 ## Mostek clock found on 4/300, sun4c, sun4m and sun4d systems. 297 ## The Mostek clock NVRAM is the "eeprom" on sun4/300 systems. 298 clock0 at mainbus0 # sun4c 299 clock0 at obio0 # sun4m 300 clock0 at obio0 addr 0xf2000000 # sun4/300 301 clock0 at bootbus0 # sun4d 302 303 ## Intersil clock found on 4/100 and 4/200 systems. 304 oclock0 at obio0 addr 0xf3000000 # sun4/200 305 oclock0 at obio0 addr 0x03000000 # sun4/100 306 307 ## Memory error registers. 308 memreg0 at mainbus0 # sun4c 309 memreg0 at obio0 # sun4m 310 memreg0 at obio0 addr 0xf4000000 # sun4/200 and sun4/300 311 memreg0 at obio0 addr 0x04000000 # sun4/100 312 313 ## ECC memory control 314 eccmemctl0 at mainbus0 # sun4m 315 316 ## Timer chip found on 4/300, sun4c, and sun4m systems. 317 timer0 at mainbus0 # sun4c 318 timer0 at obio0 # sun4m 319 timer0 at obio0 addr 0xef000000 # sun4/300 320 321 ## EEPROM found on 4/100 and 4/200 systems. Note that the 4/300 322 ## doesn't use this driver; the `EEPROM' is in the NVRAM on the 323 ## Mostek clock chip on 4/300 systems. 324 eeprom0 at obio0 addr 0xf2000000 # sun4/200 325 eeprom0 at obio0 addr 0x02000000 # sun4/100 326 327 328 #### Serial port configuration 329 330 ## Zilog 8530 serial chips. Each has two-channels. 331 ## zs0 is ttya and ttyb. zs1 is the keyboard and mouse. 332 zs0 at mainbus0 # sun4c 333 zs0 at obio0 # sun4m 334 zs0 at obio0 addr 0xf1000000 level 12 # sun4/200 and sun4/300 335 zs0 at obio0 addr 0x01000000 level 12 # sun4/100 336 zs0 at bootbus0 # sun4d 337 zstty0 at zs0 channel 0 # ttya 338 zstty1 at zs0 channel 1 # ttyb 339 340 zs1 at mainbus0 # sun4c 341 zs1 at obio0 # sun4m 342 zs1 at obio0 addr 0xf0000000 level 12 # sun4/200 and sun4/300 343 zs1 at obio0 addr 0x00000000 level 12 # sun4/100 344 zs1 at bootbus0 # sun4d 345 346 # old kbd and mouse attachments 347 #kbd0 at zs1 channel 0 # keyboard 348 #ms0 at zs1 channel 1 # mouse 349 zstty* at zs? 350 351 # these are for wscons 352 kbd0 at zstty? 353 ms0 at zstty? 354 wskbd* at wskbddev? 355 wsmouse* at wsmousedev? 356 357 zs2 at obio0 addr 0xe0000000 level 12 # sun4/300 358 zstty2 at zs2 channel 0 # ttyc 359 zstty3 at zs2 channel 1 # ttyd 360 361 zs* at bootbus? # sun4d 362 zstty* at zs? 363 364 ## NS16x50 serial chips and clones. Present on the 365 ## Sun JavaStation-1 and Tadpole SPARCbook 3 366 com* at obio0 # sun4m 367 368 # Parallel port. 369 bpp* at sbus? slot? offset ? 370 371 ## Magma Serial/Parallel driver 372 magma* at sbus? slot ? offset ? 373 mtty* at magma? 374 mbpp* at magma? 375 376 ## SUNW,spif Serial/Parallel driver 377 spif* at sbus? slot ? offset ? 378 stty* at spif? 379 sbpp* at spif? 380 381 ## PCMCIA serial interfaces 382 #com* at pcmcia? 383 #pcmcom* at pcmcia? 384 #com* at pcmcom? 385 386 #### Disk controllers and disks 387 388 # 389 390 ## The following flags may be set for the NCR53c94 based esp driver: 391 ## bits 0-7: disable disconnect/reselect for the corresponding target 392 ## bits 8-15: disable synchronous negotiation for target [bit-8] 393 394 ## sun4/300, sun4c, sun4m on-board SCSI, and FSBE/S SBus SCSI cards. 395 ## Both `dma' and `esp' are needed in all cases. 396 ## Two kinds of additional SBus SCSI interfaces are available. One uses 397 ## "esp at sbus" like the sun4c on-board; the other uses "esp at dma". 398 399 ## sun4/300 SCSI - an NCR53c94 or equivalent behind 400 ## an LSI Logic DMA controller 401 402 dma0 at obio0 addr 0xfa001000 level 4 # sun4/300 403 esp0 at obio0 addr 0xfa000000 level 4 flags 0x0000 # sun4/300 404 405 dma0 at sbus0 slot ? offset ? # sun4c/sun4m 406 esp0 at sbus0 slot ? offset ? flags 0x0000 # sun4c 407 esp0 at dma0 flags 0x0000 # sun4m 408 409 # FSBE/S SCSI & SunSwift Sbus FAS366 410 dma* at sbus? slot ? offset ? # SBus 411 esp* at sbus? slot ? offset ? flags 0x0000 # SBus 412 esp* at dma? flags 0x0000 # SBus 413 414 scsibus* at esp? 415 416 ## Qlogic ISP SBus SCSI Card 417 isp* at sbus? slot ? offset ? 418 scsibus* at isp? 419 420 ## NCR5380-based "Sun SCSI 3" VME SCSI controller. 421 ## This driver has several flags which may be enabled by OR'ing 422 ## the values and using the "flags" directive. 423 ## Valid flags are: 424 ## 425 ## 0x01 Use DMA (may be polled) 426 ## 0x02 Use DMA completion interrupts 427 ## 0x04 Allow disconnect/reselect 428 ## 429 ## E.g. the following would enable DMA, interrupts, and reselect: 430 ## si0 at vme0 addr 0x200000 irq 3 vect 0x40 flags 0x07 431 ## 432 ## By default, DMA is enabled in the driver. 433 434 si0 at vme0 addr 0x200000 irq 2 vect 0x40 435 scsibus* at si? 436 437 ## NCR5380-based "SCSI Weird" on-board SCSI interface found 438 ## on sun4/100 systems. The flags are the same as the "si" 439 ## controller. Note, while DMA is enabled by default, only 440 ## polled DMA works at this time, and reselects do not work 441 ## on this particular controller. 442 443 sw0 at obio0 addr 0x0a000000 level 3 444 scsibus* at sw? 445 446 ## PCMCIA SCSI controllers 447 #aic* at pcmcia? 448 #spc* at pcmcia? 449 #scsibus* at aic? 450 #scsibus* at spc? 451 452 453 ## These entries find devices on all SCSI busses and assign 454 ## unit numbers dynamically. 455 sd* at scsibus? target ? lun ? # SCSI disks 456 st* at scsibus? target ? lun ? # SCSI tapes 457 cd* at scsibus? target ? lun ? # SCSI CD-ROMs 458 ch* at scsibus? target ? lun ? # SCSI changer devices 459 ss* at scsibus? target ? lun ? # SCSI scanners 460 ses* at scsibus? target ? lun ? # SCSI SES/SAF-TE 461 uk* at scsibus? target ? lun ? # unknown SCSI 462 463 464 ## Xylogics 753 or 7053 VME SMD disk controllers and disks, found 465 ## on sun4 systems. 466 xdc0 at vme0 addr 0xee80 irq 3 vect 0x44 467 xdc1 at vme0 addr 0xee90 irq 3 vect 0x45 468 xdc2 at vme0 addr 0xeea0 irq 3 vect 0x46 469 xdc3 at vme0 addr 0xeeb0 irq 3 vect 0x47 470 xd* at xdc? drive ? 471 472 ## Xylogics 451 or 451 VME SMD disk controllers and disks, found 473 ## on sun4 systems. 474 xyc0 at vme0 addr 0xee40 irq 3 vect 0x48 475 xyc1 at vme0 addr 0xee48 irq 3 vect 0x49 476 xy* at xyc? drive ? 477 478 479 ## Floppy controller and drive found on SPARCstations. 480 481 fdc0 at mainbus0 # sun4c controller 482 fdc0 at obio0 # sun4m controller 483 fd* at fdc0 # the drive itself 484 485 ## PCMCIA IDE controllers 486 #wdc* at pcmcia? 487 #atabus* at ata? 488 #wd* at atabus? drive ? flags 0x0000 489 490 ## A disk-like interface to files. Can be used to create floppy, CD, 491 ## miniroot images, etc. 492 493 pseudo-device vnd 494 #options VND_COMPRESSION # compressed vnd(4) 495 496 ## Concatenated and striped disks; with this, you can create a software-based 497 ## disk array similar to a "RAID 0" setup. See ccd(4). 498 499 pseudo-device ccd 4 500 501 ## Cryptographic disk devices; See cgd(4) 502 503 #pseudo-device cgd 4 504 505 ## RAIDframe disk driver: software RAID driver. See raid(4). 506 507 pseudo-device raid 8 508 options RAID_AUTOCONFIG # auto-configuration of RAID components 509 # Options to enable various other RAIDframe RAID types. 510 # options RF_INCLUDE_EVENODD=1 511 # options RF_INCLUDE_RAID5_RS=1 512 # options RF_INCLUDE_PARITYLOGGING=1 513 # options RF_INCLUDE_CHAINDECLUSTER=1 514 # options RF_INCLUDE_INTERDECLUSTER=1 515 # options RF_INCLUDE_PARITY_DECLUSTERING=1 516 # options RF_INCLUDE_PARITY_DECLUSTERING_DS=1 517 518 519 ## Memory disk device, used on boot floppies with compressed 520 ## kernel-plus-root-disk images. 521 522 #pseudo-device md 523 524 525 #### Network interfaces 526 527 ## LANCE Ethernet - an AMD 7990 LANCE behind specialized DMA glue 528 ## Three flavors of additional SBus ethernets are available. One attaches 529 ## directly like the sun4c on-board, one uses the ledma device like the 530 ## sun4m on-board, and one uses the lebuffer device. 531 532 le0 at obio0 addr 0xf9000000 level 6 # sun4/300 533 le0 at sbus0 slot ? offset ? # sun4c on-board 534 ledma0 at sbus0 slot ? offset ? # sun4m on-board 535 le0 at ledma0 # sun4m on-board 536 le* at sbus? slot ? offset ? # SBus 537 ledma* at sbus? slot ? offset ? # SBus 538 le* at ledma? # SBus 539 lebuffer0 at sbus? slot ? offset ? # SBus 540 le0 at lebuffer? # SBus 541 lebuffer* at sbus? slot ? offset ? # SBus 542 le* at lebuffer? # SBus 543 544 545 ## sun4/100 and sun4/200 Ethernet - an Intel 82586 on-board 546 ## or on a Multibus/VME card. 547 ie0 at obio0 addr 0xf6000000 level 6 # sun4/200 on-board 548 ie0 at obio0 addr 0x06000000 level 6 # sun4/100 on-board 549 ## VME: the first [addr,len] pair specifies the device registers; 550 ## the second pair specifies the on-board memory buffer 551 ie1 at vme0 addr 0xe88000,0xe00000 len -1,0x40000 irq 3 vect 0x75 552 ie2 at vme0 addr 0x31ff02,0x300000 len -1,0x40000 irq 3 vect 0x76 553 ie3 at vme0 addr 0x35ff02,0x300000 len -1,0x40000 irq 3 vect 0x77 554 ie4 at vme0 addr 0x2dff02,0x200000 len -1,0x40000 irq 3 vect 0x7c 555 556 ## Quad Ethernet Controller with BigMac (be, 10/100MBd) and Mace Ethernet 557 ## (qe, 10MBd) attached. 558 qec* at sbus? slot ? offset ? # Quad Ethernet Controller 559 be* at qec? # BigMac Ethernet (10/100MBd) 560 qe* at qec? # Mace Ethernet (10MBd) 561 562 ## Happy Meal Ethernet 563 hme* at sbus? slot ? offset ? 564 565 # midway ATM 566 en0 at sbus? slot ? offset ? 567 568 # PCMCIA ethernet devices 569 #ep* at pcmcia? 570 #mbe* at pcmcia? 571 #ne* at pcmcia? 572 #sm* at pcmcia? 573 574 ## PCMCIA wavelan card 575 #wi* at pcmcia? function ? # Lucent WaveLan IEEE (802.11) 576 577 # MII/PHY support 578 exphy* at mii? phy ? # 3Com internal PHYs 579 icsphy* at mii? phy ? # Integrated Circuit Systems ICS189x 580 inphy* at mii? phy ? # Intel 82555 PHYs 581 lxtphy* at mii? phy ? # Level One LXT-970 PHYs 582 nsphy* at mii? phy ? # NS83840 PHYs 583 qsphy* at mii? phy ? # Quality Semiconductor QS6612 PHYs 584 sqphy* at mii? phy ? # Seeq 80220/80221/80223 PHYs 585 tlphy* at mii? phy ? # ThunderLAN PHYs 586 ukphy* at mii? phy ? # generic unknown PHYs 587 588 ## Loopback network interface; required 589 pseudo-device loop 590 591 ## SLIP and CSLIP interfaces, for IP over a serial line. 592 pseudo-device sl 593 594 ## PPP, the successor to SLIP. See pppd(8). 595 pseudo-device ppp 596 597 ## PPP over Ethernet (RFC 2516) 598 pseudo-device pppoe 599 600 ## Starmode Radio IP, a special hardware network device. 601 #pseudo-device strip 602 603 ## Network "tunnel" device, allowing protocol stacks to run in the userland. 604 ## This is used by the third-party user-mode "ppp" program, and others. 605 pseudo-device tun 606 pseudo-device tap # virtual Ethernet 607 608 ## Generic L3 over IP tunnel 609 #pseudo-device gre # generic L3 over IP tunnel 610 611 ## Berkeley Packet Filter, required to run RARPD. A generic C-language 612 ## interface that allows selective examining of incoming packets. 613 pseudo-device bpfilter 614 615 #pseudo-device carp # Common Address Redundancy Protocol 616 617 ## IP Filter, used in firewall and NAT applications. See ipnat(8) for 618 ## one example of the use of the IP Filter. 619 pseudo-device ipfilter 620 621 ## for IPv6 622 pseudo-device gif # IPv[46] over IPv[46] tunnel (RFC1933) 623 #pseudo-device faith # IPv[46] tcp relay translation i/f 624 pseudo-device stf # 6to4 IPv6 over IPv4 encapsulation 625 626 ## IEEE 802.1Q Virtual LAN encapsulation, see vlan(4). 627 pseudo-device vlan 628 629 ## Simple inter-network traffic bridging 630 pseudo-device bridge 631 #options BRIDGE_IPF # bridge uses IP/IPv6 pfil hooks too 632 pseudo-device agr # IEEE 802.3ad link aggregation 633 634 ## accept filters 635 pseudo-device accf_data # "dataready" accept filter 636 pseudo-device accf_http # "httpready" accept filter 637 638 #### Audio and video devices 639 640 ## /dev/audio support (`audioamd' plus `audio') 641 ## 642 audioamd0 at mainbus0 # sun4c 643 audioamd0 at obio0 # sun4m 644 audioamd0 at sbus0 slot ? offset ? # sun4m 645 646 audiocs0 at sbus0 slot ? offset ? # SUNW,CS4231 647 648 #options DBRI_DEBUG # noisy debug output from the dbri driver 649 #options DBRI_BIG_BUFFER # use bigger DMA buffers, for slow CPUs 650 dbri* at sbus? slot ? offset ? # SUNW,DBRI[s3|e] 651 652 audio* at audiobus? 653 654 ## Sun "bwtwo" black and white framebuffer, found on sun4, sun4c, and sun4m 655 ## systems. If your sun4 system has a cgfour installed in the P4 slot, 656 ## the P4 entries for "bwtwo" will attach to the overlay plane of the 657 ## "cgfour". 658 659 bwtwo0 at sbus0 slot ? offset ? # sun4c and sun4m 660 bwtwo* at sbus? slot ? offset ? # 661 bwtwo0 at obio0 addr 0xfd000000 level 4 # sun4/200 662 bwtwo0 at obio0 addr 0xfb300000 level 4 # sun4/300 in P4 slot 663 bwtwo0 at obio0 addr 0x0b300000 level 4 # sun4/100 in P4 slot 664 665 ## Sun "cgtwo" VME color framebuffer 666 # XXX no wsdisplay support 667 #cgtwo0 at vme0 addr 0x400000 irq ? vect 0xa8 668 669 ## Sun "cgthree" Sbus color framebuffer 670 cgthree0 at sbus? slot ? offset ? 671 cgthree* at sbus? slot ? offset ? 672 673 ## Sun "cgfour" color framebuffer with overlay plane. See above comment 674 ## regarding overlay plane. 675 # XXX no wsdisplay support 676 #cgfour0 at obio0 addr 0xfb300000 level 4 # sun4/300 P4 677 #cgfour0 at obio0 addr 0x0b300000 level 4 # sun4/100 P4 678 679 ## Sun "cgsix" accelerated color framebuffer. 680 cgsix0 at sbus? slot ? offset ? 681 cgsix* at sbus? slot ? offset ? 682 cgsix0 at obio0 addr 0xfb000000 level 4 # sun4/300 P4 683 cgsix0 at obio0 addr 0x0b000000 level 4 # sun4/100 P4 684 685 ## Sun "cgeight" 24-bit framebuffer 686 # XXX no wsdisplay support 687 #cgeight0 at obio0 addr 0xfb300000 level 4 # sun4/300 P4 688 #cgeight0 at obio0 addr 0x0b300000 level 4 # sun4/100 P4 689 690 ## Sun "tcx" accelerated color framebuffer. 691 # there can be only one 692 tcx0 at sbus? slot ? offset ? 693 694 ## Sun CG12 / Matrox SG3 accelerated 24bit framebuffer 695 ## runs monochrome only for now 696 cgtwelve* at sbus? slot ? offset ? 697 698 # Sun "cgfourteen" accelerated 24-bit framebuffer. 699 cgfourteen* at obio0 # sun4m 700 701 # P9100-based display on Tadpole SPARCbook 3. 702 pnozz0 at sbus? slot ? offset ? 703 # the SPARCbook 3 hardware docs say that accesses to P9100 registers need to be 704 # 'latched in' but at least my 3GX works happily without 705 # Enable it by default since we don't know which hardware really needs it. 706 options PNOZZ_USE_LATCH 707 708 # Sun ZX/Leo 24-bit framebuffer 709 zx* at sbus? slot ? offset ? 710 711 # Fujitsu AG-10e accelerated graphics 8/24-bit board 712 agten* at sbus? slot ? offset ? 713 714 # generic framebuffer console 715 genfb* at sbus? slot ? offset ? 716 717 # make sure wsdisplay0 is the console 718 wsdisplay0 at wsemuldisplaydev? console 1 719 wsdisplay* at wsemuldisplaydev? 720 721 #### Other device configuration 722 723 # Tadpole microcontroller 724 tctrl0 at obio0 725 726 # Aurora Personality Chip (APC) on SPARCstation-4/5 727 # Not enabled by default as it may hang some systems 728 #apc* at sbus? slot ? offset ? 729 730 ## Pseudo ttys, required for network logins and programs like screen. 731 732 pseudo-device pty # pseudo-terminals 733 734 ## Random device, used to implement /dev/random (a source of random noise), 735 ## and generate randomness for some kernel formulae. 736 737 738 # a pseudo device needed for Coda # also needs CODA (above) 739 pseudo-device vcoda 4 # coda minicache <-> venus comm. 740 741 pseudo-device clockctl # user control of clock subsystem 742 pseudo-device ksyms # /dev/ksyms 743 #pseudo-device pf # PF packet filter 744 #pseudo-device pflog # PF log if 745 pseudo-device fss # file system snapshot device 746 pseudo-device wsmux # mouse and keyboard multiplexor 747 pseudo-device wsfont 748 pseudo-device putter # for puffs and pud 749 750 #options FILEASSOC # fileassoc(9) 751 752 # Veriexec 753 # 754 # a pseudo device needed for veriexec 755 #pseudo-device veriexec 1 756 # 757 # Uncomment the fingerprint methods below that are desired. Note that 758 # removing fingerprint methods will have almost no impact on the kernel 759 # code size. 760 # 761 #options VERIFIED_EXEC_FP_RMD160 762 #options VERIFIED_EXEC_FP_SHA256 763 #options VERIFIED_EXEC_FP_SHA384 764 #options VERIFIED_EXEC_FP_SHA512 765 #options VERIFIED_EXEC_FP_SHA1 766 #options VERIFIED_EXEC_FP_MD5 767 768 #options PAX_MPROTECT=0 # PaX mprotect(2) restrictions 769 # (for static binaries only for now) 770
Indexes created Thu Oct 02 01:09:59 GMT 2025