GENERIC revision 1.234
1# $NetBSD: GENERIC,v 1.234 2012/08/17 19:43:25 abs Exp $ 2# 3# GENERIC machine description file 4# 5# This machine description file is used to generate the default NetBSD 6# kernel. The generic kernel does not include all options, subsystems 7# and device drivers, but should be useful for most applications. 8# 9# The machine description file can be customised for your specific 10# machine to reduce the kernel size and improve its performance. 11# 12# For further information on compiling NetBSD kernels, see the config(8) 13# man page. 14# 15# For further information on hardware support for this architecture, see 16# the intro(4) man page. For further information about kernel options 17# for this architecture, see the options(4) man page. For an explanation 18# of each device driver in this file see the section 4 man page for the 19# device. 20 21include "arch/sparc/conf/std.sparc" 22 23options INCLUDE_CONFIG_FILE # embed config file in kernel binary 24 25#ident "GENERIC-$Revision: 1.234 $" 26 27maxusers 32 28 29## System kernel configuration. See options(4) for more detail. 30 31 32# Options for variants of the Sun SPARC architecure. 33# We currently support three architecture types; at least one is required. 34options SUN4 # sun4/100, sun4/200, sun4/300 35options SUN4C # sun4c - SS1, 1+, 2, ELC, SLC, IPC, IPX, etc. 36options SUN4M # sun4m - SS10, SS20, Classic, etc. 37options SUN4D # sun4d - SS1000, SC2000 38 39options SUN4_MMU3L # sun4/400 3-level MMU 40 41## System options specific to the sparc machine type 42 43# Blink the power LED on some machines to indicate the system load. 44#options BLINK 45 46## Use a faster console than the PROM's slow drawing routines. Not needed 47## for headless (no framebuffer) machines. 48## These is obsolete for wscons kernels 49#options RASTERCONSOLE # fast rasterop console 50#options RASTERCONSOLE_FGCOL=WSCOL_BLACK 51#options RASTERCONSOLE_BGCOL=WSCOL_WHITE 52 53# wscons stuff 54#options WSEMUL_SUN 55options WSEMUL_VT100 56options WSDISPLAY_COMPAT_RAWKBD 57options WSDISPLAY_CUSTOM_OUTPUT 58options WS_DEFAULT_FG=WSCOL_BLACK 59options WS_DEFAULT_BG=WSCOL_LIGHT_WHITE 60options WS_KERNEL_FG=WSCOL_GREEN 61options WS_KERNEL_BG=WSCOL_LIGHT_WHITE 62options WSDISPLAY_COMPAT_PCVT 63options WSDISPLAY_COMPAT_SYSCONS 64options WSDISPLAY_COMPAT_USL # wsconscfg VT handling 65 66options WSDISPLAY_SCROLLSUPPORT 67 68# generic options vlid for both wscons and RASTERCONSOLE 69options FONT_GALLANT12x22 # the console font 70options FONT_BOLD8x16 # a somewhat smaller font 71 72#### System options that are the same for all ports 73 74## Root device configuration: change the ?'s if you are going to use a 75## nonstandard root partition (other than where the kernel is booted from) 76## and/or nonstandard root type (not ffs or nfs). Normally this can be 77## automagically determined at boot time. 78 79config netbsd root on ? type ? 80 81## System call tracing (see ktrace(1)). 82options KTRACE 83 84## Collect statistics on kernel malloc's and free's. This does have a 85## significant performance hit on slower machines, so it is intended for 86## diagnostic use only. 87#options KMEMSTATS 88 89## System V compatible IPC subsystem. (msgctl(2), semctl(2), and shmctl(2)) 90options SYSVMSG # System V message queues 91options SYSVSEM # System V semaphores 92options SYSVSHM # System V shared memory 93 94options MODULAR # new style module(7) framework 95 96options USERCONF # userconf(4) support 97#options PIPE_SOCKETPAIR # smaller, but slower pipe(2) 98options SYSCTL_INCLUDE_DESCR # Include sysctl descriptions in kernel 99 100# Enable experimental buffer queue strategy for better responsiveness under 101# high disk I/O load. Use it with caution - it's not proven to be stable yet. 102#options BUFQ_READPRIO 103#options BUFQ_PRIOCSCAN 104 105## NFS boot options; tries DHCP/BOOTP then BOOTPARAM 106options NFS_BOOT_BOOTPARAM 107#options NFS_BOOT_BOOTP 108options NFS_BOOT_DHCP 109 110#### Debugging options 111 112## The DDB in-kernel debugger runs at panic (unless DDB_ONPANIC=0), or at 113## serial console break or keyboard reset, where the PROM would normally 114## intercept. DDB_HISTORY_SIZE adds up/down arrow command history. 115options DDB # kernel dynamic debugger 116options DDB_HISTORY_SIZE=100 # enable history editing in DDB 117#options DDB_ONPANIC=1 # see also sysctl(8): `ddb.onpanic' 118 119## You may also use gdb, on another computer connected to this machine over 120## a serial port. Both KGDB_DEV and KGDB_DEVRATE should be specified; 121## KGDB_DEV is a dev_t encoded device number of the serial port to use, where 122## the minor device number encodes the PROM enumeration of the serial ports, 123## i.e.: 124## 0xc00 = ttya, 0xc01 = ttyb, 0xc02 = ttyc, 0xc03 = ttyd. 125## (Note: ttyc and ttyd are available only on some sun4 models) 126#options KGDB # support for kernel gdb 127#options KGDB_DEV=0xc01 # kgdb device number (this is `ttyb') 128#options KGDB_DEVRATE=38400 # baud rate 129 130 131## Compile the kernel with debugging symbols (`netbsd.gdb' is the debug file), 132## such that gdb(1) can be used on a kernel coredump. 133 134#makeoptions DEBUG="-g" 135 136 137## Adds code to the kernel that does internal consistency checks, and will 138## cause the kernel to panic if corruption of internal data structures 139## is detected. 140#options DIAGNOSTIC # extra kernel sanity checking 141 142## Enable (possibly expensive) debugging code that may also display messages 143## on the system console 144#options DEBUG 145#options LOCKDEBUG 146#options SYSCALL_DEBUG 147 148## Make SCSI error messages more verbose when explaining their meanings. 149options SCSIVERBOSE 150 151options MIIVERBOSE # verbose PHY autoconfig messages 152 153## `INSECURE' turns off the kernel security level (securelevel = 0 always). 154## This allows writing to /dev/mem, loading kernel modules while multi-user, 155## and other insecurities good only for development work. Do not use this 156## option on a production machine. 157#options INSECURE 158 159## `FDSCRIPTS' allows non-readable but executable scripts by providing a 160## pre-opened opaque file to the script interpreter. `SETUIDSCRIPTS', 161## which implies FDSCRIPTS, allows scripts to be set-user-id using the same 162## opaque file mechanism. Perl calls this "secure setuid scripts." 163 164#options FDSCRIPTS 165#options SETUIDSCRIPTS 166 167## Options for compatibility with previous releases foreign system binaries. 168## In the cases of COMPAT_SUNOS and COMPAT_SVR4, you may need to set up 169## additional user-level utilities or system configuration files. See 170## compat_sunos(8) and compat_svr4(8). 171 172options COMPAT_43 # 4.3BSD system interfaces 173options COMPAT_10 # NetBSD 1.0 binary compatibility 174options COMPAT_11 # NetBSD 1.1 binary compatibility 175options COMPAT_12 # NetBSD 1.2 binary compatibility 176options COMPAT_13 # NetBSD 1.3 binary compatibility 177options COMPAT_14 # NetBSD 1.4 binary compatibility 178options COMPAT_15 # NetBSD 1.5 binary compatibility 179options COMPAT_16 # NetBSD 1.6 binary compatibility 180options COMPAT_20 # NetBSD 2.0 binary compatibility 181options COMPAT_30 # NetBSD 3.0 binary compatibility 182options COMPAT_40 # NetBSD 4.0 binary compatibility 183options COMPAT_50 # NetBSD 5.0 binary compatibility 184options COMPAT_SUNOS # SunOS 4.x binary compatibility 185options COMPAT_SVR4 # SunOS 5.x binary compatibility 186options COMPAT_BSDPTY # /dev/[pt]ty?? ptys. 187 188## File systems. You probably need at least one of FFS or NFS. 189file-system FFS # Berkeley Fast Filesystem 190file-system NFS # Sun NFS-compatible filesystem client 191file-system KERNFS # kernel data-structure filesystem 192file-system NULLFS # NULL layered filesystem 193file-system OVERLAY # overlay file system 194file-system MFS # memory-based filesystem 195file-system FDESC # user file descriptor filesystem 196file-system UMAPFS # uid/gid remapping filesystem 197file-system LFS # Log-based filesystem (still experimental) 198file-system PUFFS # Userspace file systems (e.g. ntfs-3g & sshfs) 199file-system PROCFS # /proc 200file-system CD9660 # ISO 9660 + Rock Ridge file system 201file-system UNION # union file system 202file-system MSDOSFS # MS-DOS FAT filesystem(s). 203file-system CODA # Coda File System; also needs vcoda (below) 204file-system PTYFS # /dev/pts/N support 205file-system TMPFS # Efficient memory file-system 206#file-system UDF # experimental - OSTA UDF CD/DVD file-system 207 208## File system options. 209options NFSSERVER # Sun NFS-compatible filesystem server 210options QUOTA # FFS quotas 211#options FFS_EI # FFS Endian Independent support 212options WAPBL # File system journaling support 213#options UFS_DIRHASH # UFS Large Directory Hashing - Experimental 214#options FFS_NO_SNAPSHOT # No FFS snapshot support 215 216## Network protocol support. In most environments, INET is required. 217options INET # IP (Internet Protocol) v4 218options INET6 # IPV6 219#options IPSEC # IP security 220#options IPSEC_ESP # IP security (encryption part; define w/IPSEC) 221#options IPSEC_NAT_T # IPsec NAT traversal (NAT-T) 222#options IPSEC_DEBUG # debug for IP security 223#options GATEWAY # packet forwarding ("router switch") 224#options MROUTING # packet forwarding of multicast packets 225#options PIM # Protocol Independent Multicast 226#options DIRECTED_BROADCAST # allow broadcasts through routers 227#options ISO,TPIP # OSI networking 228#options EON # OSI tunneling over IP 229#options NETATALK # AppleTalk (over Ethernet) protocol 230options NTP # Network Time Protocol in-kernel support 231#options PPS_SYNC # Add serial line synchronization for NTP 232options PFIL_HOOKS # Add pfil(9) packet filter hooks 233options IPFILTER_LOG # Add ipmon(8) logging for ipfilter device 234options IPFILTER_LOOKUP # ippool(8) support 235options IPFILTER_COMPAT # Compat for IP-Filter 236#options IPFILTER_DEFAULT_BLOCK # block all packets by default 237options PPP_BSDCOMP # Add BSD compression to ppp device 238options PPP_DEFLATE # Add deflate (libz) compression to ppp device 239options PPP_FILTER # Add active filters for ppp (via bpf) 240 241#options ALTQ # Manipulate network interfaces' output queues 242#options ALTQ_BLUE # Stochastic Fair Blue 243#options ALTQ_CBQ # Class-Based Queueing 244#options ALTQ_CDNR # Diffserv Traffic Conditioner 245#options ALTQ_FIFOQ # First-In First-Out Queue 246#options ALTQ_FLOWVALVE # RED/flow-valve (red-penalty-box) 247#options ALTQ_HFSC # Hierarchical Fair Service Curve 248#options ALTQ_LOCALQ # Local queueing discipline 249#options ALTQ_PRIQ # Priority Queueing 250#options ALTQ_RED # Random Early Detection 251#options ALTQ_RIO # RED with IN/OUT 252#options ALTQ_WFQ # Weighted Fair Queueing 253 254 255 256#### Main bus and CPU .. all systems. 257mainbus0 at root 258cpu0 at mainbus0 259cpuunit0 at mainbus0 # sun4d 260cpuunit* at mainbus0 # sun4d 261cpu0 at cpuunit0 # sun4d 262 263#### Bus types found on SPARC systems. 264 265sbus0 at mainbus0 # sun4c 266obio0 at mainbus0 # sun4 and sun4m 267sparcvme0 at mainbus0 # sun4 268iommu0 at mainbus0 # sun4m 269sbus0 at iommu0 # sun4m 270sparcvme0 at iommu0 # sun4m 271vme0 at sparcvme0 # MI VME attachment 272bootbus0 at cpuunit0 # sun4d 273bootbus* at cpuunit? # sun4d 274 275## SBus expander box 276xbox* at sbus? slot ? offset ? 277sbus* at xbox? 278 279## SBus to PCMCIA bridge 280nell* at sbus? slot ? offset ? # PCMCIA bridge 281pcmcia* at nell? 282tslot* at sbus? slot ? offset ? # PCMCIA bridge (tadpole 3gx) 283pcmcia* at tslot? 284 285#### Standard system devices -- all required for a given architecture 286 287## Auxiliary system registers on sun4c and sun4m 288auxreg0 at mainbus0 # sun4c 289auxreg0 at obio0 # sun4m 290auxiotwo0 at obio0 # only on Tadpole SPARCbook. 291 292## Power status and control register on Sun4m systems 293power0 at obio0 294 295## Mostek clock found on 4/300, sun4c, sun4m and sun4d systems. 296## The Mostek clock NVRAM is the "eeprom" on sun4/300 systems. 297clock0 at mainbus0 # sun4c 298clock0 at obio0 # sun4m 299clock0 at obio0 addr 0xf2000000 # sun4/300 300clock0 at bootbus0 # sun4d 301 302## Intersil clock found on 4/100 and 4/200 systems. 303oclock0 at obio0 addr 0xf3000000 # sun4/200 304oclock0 at obio0 addr 0x03000000 # sun4/100 305 306## Memory error registers. 307memreg0 at mainbus0 # sun4c 308memreg0 at obio0 # sun4m 309memreg0 at obio0 addr 0xf4000000 # sun4/200 and sun4/300 310memreg0 at obio0 addr 0x04000000 # sun4/100 311 312## ECC memory control 313eccmemctl0 at mainbus0 # sun4m 314 315## Timer chip found on 4/300, sun4c, and sun4m systems. 316timer0 at mainbus0 # sun4c 317timer0 at obio0 # sun4m 318timer0 at obio0 addr 0xef000000 # sun4/300 319 320## EEPROM found on 4/100 and 4/200 systems. Note that the 4/300 321## doesn't use this driver; the `EEPROM' is in the NVRAM on the 322## Mostek clock chip on 4/300 systems. 323eeprom0 at obio0 addr 0xf2000000 # sun4/200 324eeprom0 at obio0 addr 0x02000000 # sun4/100 325 326 327#### Serial port configuration 328 329## Zilog 8530 serial chips. Each has two-channels. 330## zs0 is ttya and ttyb. zs1 is the keyboard and mouse. 331zs0 at mainbus0 # sun4c 332zs0 at obio0 # sun4m 333zs0 at obio0 addr 0xf1000000 level 12 # sun4/200 and sun4/300 334zs0 at obio0 addr 0x01000000 level 12 # sun4/100 335zs0 at bootbus0 # sun4d 336zstty0 at zs0 channel 0 # ttya 337zstty1 at zs0 channel 1 # ttyb 338 339zs1 at mainbus0 # sun4c 340zs1 at obio0 # sun4m 341zs1 at obio0 addr 0xf0000000 level 12 # sun4/200 and sun4/300 342zs1 at obio0 addr 0x00000000 level 12 # sun4/100 343zs1 at bootbus0 # sun4d 344 345# old kbd and mouse attachments 346#kbd0 at zs1 channel 0 # keyboard 347#ms0 at zs1 channel 1 # mouse 348zstty* at zs? 349 350# these are for wscons 351kbd0 at zstty? 352ms0 at zstty? 353wskbd* at wskbddev? 354wsmouse* at wsmousedev? 355 356zs2 at obio0 addr 0xe0000000 level 12 # sun4/300 357zstty2 at zs2 channel 0 # ttyc 358zstty3 at zs2 channel 1 # ttyd 359 360zs* at bootbus? # sun4d 361zstty* at zs? 362 363## NS16x50 serial chips and clones. Present on the 364## Sun JavaStation-1 and Tadpole SPARCbook 3 365com* at obio0 # sun4m 366 367# Parallel port. 368bpp* at sbus? slot? offset ? 369 370## Magma Serial/Parallel driver 371magma* at sbus? slot ? offset ? 372mtty* at magma? 373mbpp* at magma? 374 375## SUNW,spif Serial/Parallel driver 376spif* at sbus? slot ? offset ? 377stty* at spif? 378sbpp* at spif? 379 380## PCMCIA serial interfaces 381#com* at pcmcia? 382#pcmcom* at pcmcia? 383#com* at pcmcom? 384 385#### Disk controllers and disks 386 387# 388 389## The following flags may be set for the NCR53c94 based esp driver: 390## bits 0-7: disable disconnect/reselect for the corresponding target 391## bits 8-15: disable synchronous negotiation for target [bit-8] 392 393## sun4/300, sun4c, sun4m on-board SCSI, and FSBE/S SBus SCSI cards. 394## Both `dma' and `esp' are needed in all cases. 395## Two kinds of additional SBus SCSI interfaces are available. One uses 396## "esp at sbus" like the sun4c on-board; the other uses "esp at dma". 397 398## sun4/300 SCSI - an NCR53c94 or equivalent behind 399## an LSI Logic DMA controller 400 401dma0 at obio0 addr 0xfa001000 level 4 # sun4/300 402esp0 at obio0 addr 0xfa000000 level 4 flags 0x0000 # sun4/300 403 404dma0 at sbus0 slot ? offset ? # sun4c/sun4m 405esp0 at sbus0 slot ? offset ? flags 0x0000 # sun4c 406esp0 at dma0 flags 0x0000 # sun4m 407 408# FSBE/S SCSI & SunSwift Sbus FAS366 409dma* at sbus? slot ? offset ? # SBus 410esp* at sbus? slot ? offset ? flags 0x0000 # SBus 411esp* at dma? flags 0x0000 # SBus 412 413scsibus* at esp? 414 415## Qlogic ISP SBus SCSI Card 416isp* at sbus? slot ? offset ? 417scsibus* at isp? 418 419## NCR5380-based "Sun SCSI 3" VME SCSI controller. 420## This driver has several flags which may be enabled by OR'ing 421## the values and using the "flags" directive. 422## Valid flags are: 423## 424## 0x01 Use DMA (may be polled) 425## 0x02 Use DMA completion interrupts 426## 0x04 Allow disconnect/reselect 427## 428## E.g. the following would enable DMA, interrupts, and reselect: 429## si0 at vme0 addr 0x200000 irq 3 vect 0x40 flags 0x07 430## 431## By default, DMA is enabled in the driver. 432 433si0 at vme0 addr 0x200000 irq 2 vect 0x40 434scsibus* at si? 435 436## NCR5380-based "SCSI Weird" on-board SCSI interface found 437## on sun4/100 systems. The flags are the same as the "si" 438## controller. Note, while DMA is enabled by default, only 439## polled DMA works at this time, and reselects do not work 440## on this particular controller. 441 442sw0 at obio0 addr 0x0a000000 level 3 443scsibus* at sw? 444 445## PCMCIA SCSI controllers 446#aic* at pcmcia? 447#spc* at pcmcia? 448#scsibus* at aic? 449#scsibus* at spc? 450 451 452## These entries find devices on all SCSI busses and assign 453## unit numbers dynamically. 454sd* at scsibus? target ? lun ? # SCSI disks 455st* at scsibus? target ? lun ? # SCSI tapes 456cd* at scsibus? target ? lun ? # SCSI CD-ROMs 457ch* at scsibus? target ? lun ? # SCSI changer devices 458ss* at scsibus? target ? lun ? # SCSI scanners 459ses* at scsibus? target ? lun ? # SCSI SES/SAF-TE 460uk* at scsibus? target ? lun ? # unknown SCSI 461 462 463## Xylogics 753 or 7053 VME SMD disk controllers and disks, found 464## on sun4 systems. 465xdc0 at vme0 addr 0xee80 irq 3 vect 0x44 466xdc1 at vme0 addr 0xee90 irq 3 vect 0x45 467xdc2 at vme0 addr 0xeea0 irq 3 vect 0x46 468xdc3 at vme0 addr 0xeeb0 irq 3 vect 0x47 469xd* at xdc? drive ? 470 471## Xylogics 451 or 451 VME SMD disk controllers and disks, found 472## on sun4 systems. 473xyc0 at vme0 addr 0xee40 irq 3 vect 0x48 474xyc1 at vme0 addr 0xee48 irq 3 vect 0x49 475xy* at xyc? drive ? 476 477 478## Floppy controller and drive found on SPARCstations. 479 480fdc0 at mainbus0 # sun4c controller 481fdc0 at obio0 # sun4m controller 482fd* at fdc0 # the drive itself 483 484## PCMCIA IDE controllers 485#wdc* at pcmcia? 486#atabus* at ata? 487#wd* at atabus? drive ? flags 0x0000 488 489## A disk-like interface to files. Can be used to create floppy, CD, 490## miniroot images, etc. 491 492pseudo-device vnd 493#options VND_COMPRESSION # compressed vnd(4) 494 495## Concatenated and striped disks; with this, you can create a software-based 496## disk array similar to a "RAID 0" setup. See ccd(4). 497 498pseudo-device ccd 4 499 500## Cryptographic disk devices; See cgd(4) 501 502#pseudo-device cgd 4 503 504## RAIDframe disk driver: software RAID driver. See raid(4). 505 506pseudo-device raid 8 507options RAID_AUTOCONFIG # auto-configuration of RAID components 508# Options to enable various other RAIDframe RAID types. 509# options RF_INCLUDE_EVENODD=1 510# options RF_INCLUDE_RAID5_RS=1 511# options RF_INCLUDE_PARITYLOGGING=1 512# options RF_INCLUDE_CHAINDECLUSTER=1 513# options RF_INCLUDE_INTERDECLUSTER=1 514# options RF_INCLUDE_PARITY_DECLUSTERING=1 515# options RF_INCLUDE_PARITY_DECLUSTERING_DS=1 516 517 518## Memory disk device, used on boot floppies with compressed 519## kernel-plus-root-disk images. 520 521#pseudo-device md 522 523 524#### Network interfaces 525 526## LANCE Ethernet - an AMD 7990 LANCE behind specialized DMA glue 527## Three flavors of additional SBus ethernets are available. One attaches 528## directly like the sun4c on-board, one uses the ledma device like the 529## sun4m on-board, and one uses the lebuffer device. 530 531le0 at obio0 addr 0xf9000000 level 6 # sun4/300 532le0 at sbus0 slot ? offset ? # sun4c on-board 533ledma0 at sbus0 slot ? offset ? # sun4m on-board 534le0 at ledma0 # sun4m on-board 535le* at sbus? slot ? offset ? # SBus 536ledma* at sbus? slot ? offset ? # SBus 537le* at ledma? # SBus 538lebuffer0 at sbus? slot ? offset ? # SBus 539le0 at lebuffer? # SBus 540lebuffer* at sbus? slot ? offset ? # SBus 541le* at lebuffer? # SBus 542 543 544## sun4/100 and sun4/200 Ethernet - an Intel 82586 on-board 545## or on a Multibus/VME card. 546ie0 at obio0 addr 0xf6000000 level 6 # sun4/200 on-board 547ie0 at obio0 addr 0x06000000 level 6 # sun4/100 on-board 548## VME: the first [addr,len] pair specifies the device registers; 549## the second pair specifies the on-board memory buffer 550ie1 at vme0 addr 0xe88000,0xe00000 len -1,0x40000 irq 3 vect 0x75 551ie2 at vme0 addr 0x31ff02,0x300000 len -1,0x40000 irq 3 vect 0x76 552ie3 at vme0 addr 0x35ff02,0x300000 len -1,0x40000 irq 3 vect 0x77 553ie4 at vme0 addr 0x2dff02,0x200000 len -1,0x40000 irq 3 vect 0x7c 554 555## Quad Ethernet Controller with BigMac (be, 10/100MBd) and Mace Ethernet 556## (qe, 10MBd) attached. 557qec* at sbus? slot ? offset ? # Quad Ethernet Controller 558be* at qec? # BigMac Ethernet (10/100MBd) 559qe* at qec? # Mace Ethernet (10MBd) 560 561## Happy Meal Ethernet 562hme* at sbus? slot ? offset ? 563 564# midway ATM 565en0 at sbus? slot ? offset ? 566 567# PCMCIA ethernet devices 568#ep* at pcmcia? 569#mbe* at pcmcia? 570#ne* at pcmcia? 571#sm* at pcmcia? 572 573## PCMCIA wavelan card 574#wi* at pcmcia? function ? # Lucent WaveLan IEEE (802.11) 575 576# MII/PHY support 577exphy* at mii? phy ? # 3Com internal PHYs 578icsphy* at mii? phy ? # Integrated Circuit Systems ICS189x 579inphy* at mii? phy ? # Intel 82555 PHYs 580lxtphy* at mii? phy ? # Level One LXT-970 PHYs 581nsphy* at mii? phy ? # NS83840 PHYs 582qsphy* at mii? phy ? # Quality Semiconductor QS6612 PHYs 583sqphy* at mii? phy ? # Seeq 80220/80221/80223 PHYs 584tlphy* at mii? phy ? # ThunderLAN PHYs 585ukphy* at mii? phy ? # generic unknown PHYs 586 587## Loopback network interface; required 588pseudo-device loop 589 590## SLIP and CSLIP interfaces, for IP over a serial line. 591pseudo-device sl 592 593## PPP, the successor to SLIP. See pppd(8). 594pseudo-device ppp 595 596## PPP over Ethernet (RFC 2516) 597pseudo-device pppoe 598 599## Starmode Radio IP, a special hardware network device. 600#pseudo-device strip 601 602## Network "tunnel" device, allowing protocol stacks to run in the userland. 603## This is used by the third-party user-mode "ppp" program, and others. 604pseudo-device tun 605pseudo-device tap # virtual Ethernet 606 607## Generic L3 over IP tunnel 608#pseudo-device gre # generic L3 over IP tunnel 609 610## Berkeley Packet Filter, required to run RARPD. A generic C-language 611## interface that allows selective examining of incoming packets. 612pseudo-device bpfilter 613 614#pseudo-device carp # Common Address Redundancy Protocol 615 616## IP Filter, used in firewall and NAT applications. See ipnat(8) for 617## one example of the use of the IP Filter. 618pseudo-device ipfilter 619 620## for IPv6 621pseudo-device gif # IPv[46] over IPv[46] tunnel (RFC1933) 622#pseudo-device faith # IPv[46] tcp relay translation i/f 623pseudo-device stf # 6to4 IPv6 over IPv4 encapsulation 624 625## IEEE 802.1Q Virtual LAN encapsulation, see vlan(4). 626pseudo-device vlan 627 628## Simple inter-network traffic bridging 629pseudo-device bridge 630#options BRIDGE_IPF # bridge uses IP/IPv6 pfil hooks too 631pseudo-device agr # IEEE 802.3ad link aggregation 632 633## accept filters 634pseudo-device accf_data # "dataready" accept filter 635pseudo-device accf_http # "httpready" accept filter 636 637#### Audio and video devices 638 639## /dev/audio support (`audioamd' plus `audio') 640## 641audioamd0 at mainbus0 # sun4c 642audioamd0 at obio0 # sun4m 643audioamd0 at sbus0 slot ? offset ? # sun4m 644 645audiocs0 at sbus0 slot ? offset ? # SUNW,CS4231 646 647#options DBRI_DEBUG # noisy debug output from the dbri driver 648#options DBRI_BIG_BUFFER # use bigger DMA buffers, for slow CPUs 649dbri* at sbus? slot ? offset ? # SUNW,DBRI[s3|e] 650 651audio* at audiobus? 652 653## Sun "bwtwo" black and white framebuffer, found on sun4, sun4c, and sun4m 654## systems. If your sun4 system has a cgfour installed in the P4 slot, 655## the P4 entries for "bwtwo" will attach to the overlay plane of the 656## "cgfour". 657 658bwtwo0 at sbus0 slot ? offset ? # sun4c and sun4m 659bwtwo* at sbus? slot ? offset ? # 660bwtwo0 at obio0 addr 0xfd000000 level 4 # sun4/200 661bwtwo0 at obio0 addr 0xfb300000 level 4 # sun4/300 in P4 slot 662bwtwo0 at obio0 addr 0x0b300000 level 4 # sun4/100 in P4 slot 663 664## Sun "cgtwo" VME color framebuffer 665# XXX no wsdisplay support 666#cgtwo0 at vme0 addr 0x400000 irq ? vect 0xa8 667 668## Sun "cgthree" Sbus color framebuffer 669cgthree0 at sbus? slot ? offset ? 670cgthree* at sbus? slot ? offset ? 671 672## Sun "cgfour" color framebuffer with overlay plane. See above comment 673## regarding overlay plane. 674# XXX no wsdisplay support 675#cgfour0 at obio0 addr 0xfb300000 level 4 # sun4/300 P4 676#cgfour0 at obio0 addr 0x0b300000 level 4 # sun4/100 P4 677 678## Sun "cgsix" accelerated color framebuffer. 679cgsix0 at sbus? slot ? offset ? 680cgsix* at sbus? slot ? offset ? 681cgsix0 at obio0 addr 0xfb000000 level 4 # sun4/300 P4 682cgsix0 at obio0 addr 0x0b000000 level 4 # sun4/100 P4 683 684## Sun "cgeight" 24-bit framebuffer 685# XXX no wsdisplay support 686#cgeight0 at obio0 addr 0xfb300000 level 4 # sun4/300 P4 687#cgeight0 at obio0 addr 0x0b300000 level 4 # sun4/100 P4 688 689## Sun "tcx" accelerated color framebuffer. 690# there can be only one 691tcx0 at sbus? slot ? offset ? 692 693## Sun CG12 / Matrox SG3 accelerated 24bit framebuffer 694## runs monochrome only for now 695cgtwelve* at sbus? slot ? offset ? 696 697# Sun "cgfourteen" accelerated 24-bit framebuffer. 698cgfourteen* at obio0 # sun4m 699 700# P9100-based display on Tadpole SPARCbook 3. 701pnozz0 at sbus? slot ? offset ? 702# the SPARCbook 3 hardware docs say that accesses to P9100 registers need to be 703# 'latched in' but at least my 3GX works happily without 704# Enable it by default since we don't know which hardware really needs it. 705options PNOZZ_USE_LATCH 706 707# Sun ZX/Leo 24-bit framebuffer 708zx* at sbus? slot ? offset ? 709 710# Fujitsu AG-10e accelerated graphics 8/24-bit board 711agten* at sbus? slot ? offset ? 712 713# generic framebuffer console 714genfb* at sbus? slot ? offset ? 715 716# make sure wsdisplay0 is the console 717wsdisplay0 at wsemuldisplaydev? console 1 718wsdisplay* at wsemuldisplaydev? 719 720#### Other device configuration 721 722# Tadpole microcontroller 723tctrl0 at obio0 724 725# Aurora Personality Chip (APC) on SPARCstation-4/5 726# Not enabled by default as it may hang some systems 727#apc* at sbus? slot ? offset ? 728 729## Pseudo ttys, required for network logins and programs like screen. 730 731pseudo-device pty # pseudo-terminals 732 733## Random device, used to implement /dev/random (a source of random noise), 734## and generate randomness for some kernel formulae. 735 736 737# a pseudo device needed for Coda # also needs CODA (above) 738pseudo-device vcoda 4 # coda minicache <-> venus comm. 739 740pseudo-device clockctl # user control of clock subsystem 741pseudo-device ksyms # /dev/ksyms 742#pseudo-device pf # PF packet filter 743#pseudo-device pflog # PF log if 744pseudo-device fss # file system snapshot device 745pseudo-device wsmux # mouse and keyboard multiplexor 746pseudo-device wsfont 747pseudo-device putter # for puffs and pud 748 749#options FILEASSOC # fileassoc(9) 750 751# Veriexec 752# 753# a pseudo device needed for veriexec 754#pseudo-device veriexec 1 755# 756# Uncomment the fingerprint methods below that are desired. Note that 757# removing fingerprint methods will have almost no impact on the kernel 758# code size. 759# 760#options VERIFIED_EXEC_FP_RMD160 761#options VERIFIED_EXEC_FP_SHA256 762#options VERIFIED_EXEC_FP_SHA384 763#options VERIFIED_EXEC_FP_SHA512 764#options VERIFIED_EXEC_FP_SHA1 765#options VERIFIED_EXEC_FP_MD5 766 767#options PAX_MPROTECT=0 # PaX mprotect(2) restrictions 768 # (for static binaries only for now) 769