GENERIC revision 1.236
1# $NetBSD: GENERIC,v 1.236 2013/02/07 16:19:15 macallan Exp $ 2# 3# GENERIC machine description file 4# 5# This machine description file is used to generate the default NetBSD 6# kernel. The generic kernel does not include all options, subsystems 7# and device drivers, but should be useful for most applications. 8# 9# The machine description file can be customised for your specific 10# machine to reduce the kernel size and improve its performance. 11# 12# For further information on compiling NetBSD kernels, see the config(8) 13# man page. 14# 15# For further information on hardware support for this architecture, see 16# the intro(4) man page. For further information about kernel options 17# for this architecture, see the options(4) man page. For an explanation 18# of each device driver in this file see the section 4 man page for the 19# device. 20 21include "arch/sparc/conf/std.sparc" 22 23options INCLUDE_CONFIG_FILE # embed config file in kernel binary 24 25#ident "GENERIC-$Revision: 1.236 $" 26 27maxusers 32 28 29## System kernel configuration. See options(4) for more detail. 30 31 32# Options for variants of the Sun SPARC architecure. 33# We currently support three architecture types; at least one is required. 34options SUN4 # sun4/100, sun4/200, sun4/300 35options SUN4C # sun4c - SS1, 1+, 2, ELC, SLC, IPC, IPX, etc. 36options SUN4M # sun4m - SS10, SS20, Classic, etc. 37options SUN4D # sun4d - SS1000, SC2000 38 39options SUN4_MMU3L # sun4/400 3-level MMU 40 41## System options specific to the sparc machine type 42 43# Blink the power LED on some machines to indicate the system load. 44#options BLINK 45 46## Use a faster console than the PROM's slow drawing routines. Not needed 47## for headless (no framebuffer) machines. 48## These is obsolete for wscons kernels 49#options RASTERCONSOLE # fast rasterop console 50#options RASTERCONSOLE_FGCOL=WSCOL_BLACK 51#options RASTERCONSOLE_BGCOL=WSCOL_WHITE 52 53# wscons stuff 54#options WSEMUL_SUN 55options WSEMUL_VT100 56options WSDISPLAY_COMPAT_RAWKBD 57options WSDISPLAY_CUSTOM_OUTPUT 58options WS_DEFAULT_FG=WSCOL_BLACK 59options WS_DEFAULT_BG=WSCOL_LIGHT_WHITE 60options WS_KERNEL_FG=WSCOL_GREEN 61options WS_KERNEL_BG=WSCOL_LIGHT_WHITE 62options WSDISPLAY_COMPAT_PCVT 63options WSDISPLAY_COMPAT_SYSCONS 64options WSDISPLAY_COMPAT_USL # wsconscfg VT handling 65 66options WSDISPLAY_SCROLLSUPPORT 67 68# generic options vlid for both wscons and RASTERCONSOLE 69options FONT_GALLANT12x22 # the console font 70options FONT_BOLD8x16 # a somewhat smaller font 71 72#### System options that are the same for all ports 73 74## Root device configuration: change the ?'s if you are going to use a 75## nonstandard root partition (other than where the kernel is booted from) 76## and/or nonstandard root type (not ffs or nfs). Normally this can be 77## automagically determined at boot time. 78 79config netbsd root on ? type ? 80 81## System call tracing (see ktrace(1)). 82options KTRACE 83 84## Collect statistics on kernel malloc's and free's. This does have a 85## significant performance hit on slower machines, so it is intended for 86## diagnostic use only. 87#options KMEMSTATS 88 89## System V compatible IPC subsystem. (msgctl(2), semctl(2), and shmctl(2)) 90options SYSVMSG # System V message queues 91options SYSVSEM # System V semaphores 92options SYSVSHM # System V shared memory 93 94options MODULAR # new style module(7) framework 95 96options USERCONF # userconf(4) support 97#options PIPE_SOCKETPAIR # smaller, but slower pipe(2) 98options SYSCTL_INCLUDE_DESCR # Include sysctl descriptions in kernel 99 100# Enable experimental buffer queue strategy for better responsiveness under 101# high disk I/O load. Use it with caution - it's not proven to be stable yet. 102#options BUFQ_READPRIO 103#options BUFQ_PRIOCSCAN 104 105## NFS boot options; tries DHCP/BOOTP then BOOTPARAM 106options NFS_BOOT_BOOTPARAM 107#options NFS_BOOT_BOOTP 108options NFS_BOOT_DHCP 109 110#### Debugging options 111 112## The DDB in-kernel debugger runs at panic (unless DDB_ONPANIC=0), or at 113## serial console break or keyboard reset, where the PROM would normally 114## intercept. DDB_HISTORY_SIZE adds up/down arrow command history. 115options DDB # kernel dynamic debugger 116options DDB_HISTORY_SIZE=100 # enable history editing in DDB 117#options DDB_ONPANIC=1 # see also sysctl(8): `ddb.onpanic' 118 119## You may also use gdb, on another computer connected to this machine over 120## a serial port. Both KGDB_DEV and KGDB_DEVRATE should be specified; 121## KGDB_DEV is a dev_t encoded device number of the serial port to use, where 122## the minor device number encodes the PROM enumeration of the serial ports, 123## i.e.: 124## 0xc00 = ttya, 0xc01 = ttyb, 0xc02 = ttyc, 0xc03 = ttyd. 125## (Note: ttyc and ttyd are available only on some sun4 models) 126#options KGDB # support for kernel gdb 127#options KGDB_DEV=0xc01 # kgdb device number (this is `ttyb') 128#options KGDB_DEVRATE=38400 # baud rate 129 130 131## Compile the kernel with debugging symbols (`netbsd.gdb' is the debug file), 132## such that gdb(1) can be used on a kernel coredump. 133 134#makeoptions DEBUG="-g" 135 136 137## Adds code to the kernel that does internal consistency checks, and will 138## cause the kernel to panic if corruption of internal data structures 139## is detected. 140#options DIAGNOSTIC # extra kernel sanity checking 141 142## Enable (possibly expensive) debugging code that may also display messages 143## on the system console 144#options DEBUG 145#options LOCKDEBUG 146#options SYSCALL_DEBUG 147 148## Make SCSI error messages more verbose when explaining their meanings. 149options SCSIVERBOSE 150 151options MIIVERBOSE # verbose PHY autoconfig messages 152 153## `INSECURE' turns off the kernel security level (securelevel = 0 always). 154## This allows writing to /dev/mem, loading kernel modules while multi-user, 155## and other insecurities good only for development work. Do not use this 156## option on a production machine. 157#options INSECURE 158 159## `FDSCRIPTS' allows non-readable but executable scripts by providing a 160## pre-opened opaque file to the script interpreter. `SETUIDSCRIPTS', 161## which implies FDSCRIPTS, allows scripts to be set-user-id using the same 162## opaque file mechanism. Perl calls this "secure setuid scripts." 163 164#options FDSCRIPTS 165#options SETUIDSCRIPTS 166 167## Options for compatibility with previous releases foreign system binaries. 168## In the cases of COMPAT_SUNOS and COMPAT_SVR4, you may need to set up 169## additional user-level utilities or system configuration files. See 170## compat_sunos(8) and compat_svr4(8). 171 172options COMPAT_43 # 4.3BSD system interfaces 173options COMPAT_10 # NetBSD 1.0 binary compatibility 174options COMPAT_11 # NetBSD 1.1 binary compatibility 175options COMPAT_12 # NetBSD 1.2 binary compatibility 176options COMPAT_13 # NetBSD 1.3 binary compatibility 177options COMPAT_14 # NetBSD 1.4 binary compatibility 178options COMPAT_15 # NetBSD 1.5 binary compatibility 179options COMPAT_16 # NetBSD 1.6 binary compatibility 180options COMPAT_20 # NetBSD 2.0 binary compatibility 181options COMPAT_30 # NetBSD 3.0 binary compatibility 182options COMPAT_40 # NetBSD 4.0 binary compatibility 183options COMPAT_50 # NetBSD 5.0 binary compatibility 184options COMPAT_60 # NetBSD 6.0 compatibility. 185options COMPAT_SUNOS # SunOS 4.x binary compatibility 186options COMPAT_SVR4 # SunOS 5.x binary compatibility 187options COMPAT_BSDPTY # /dev/[pt]ty?? ptys. 188 189## File systems. You probably need at least one of FFS or NFS. 190file-system FFS # Berkeley Fast Filesystem 191file-system NFS # Sun NFS-compatible filesystem client 192file-system KERNFS # kernel data-structure filesystem 193file-system NULLFS # NULL layered filesystem 194file-system OVERLAY # overlay file system 195file-system MFS # memory-based filesystem 196file-system FDESC # user file descriptor filesystem 197file-system UMAPFS # uid/gid remapping filesystem 198file-system LFS # Log-based filesystem (still experimental) 199file-system PUFFS # Userspace file systems (e.g. ntfs-3g & sshfs) 200file-system PROCFS # /proc 201file-system CD9660 # ISO 9660 + Rock Ridge file system 202file-system UNION # union file system 203file-system MSDOSFS # MS-DOS FAT filesystem(s). 204file-system CODA # Coda File System; also needs vcoda (below) 205file-system PTYFS # /dev/pts/N support 206file-system TMPFS # Efficient memory file-system 207#file-system UDF # experimental - OSTA UDF CD/DVD file-system 208 209## File system options. 210options NFSSERVER # Sun NFS-compatible filesystem server 211options QUOTA # FFS quotas 212#options FFS_EI # FFS Endian Independent support 213options WAPBL # File system journaling support 214#options UFS_DIRHASH # UFS Large Directory Hashing - Experimental 215#options FFS_NO_SNAPSHOT # No FFS snapshot support 216 217## Network protocol support. In most environments, INET is required. 218options INET # IP (Internet Protocol) v4 219options INET6 # IPV6 220#options IPSEC # IP security 221#options IPSEC_ESP # IP security (encryption part; define w/IPSEC) 222#options IPSEC_NAT_T # IPsec NAT traversal (NAT-T) 223#options IPSEC_DEBUG # debug for IP security 224#options GATEWAY # packet forwarding ("router switch") 225#options MROUTING # packet forwarding of multicast packets 226#options PIM # Protocol Independent Multicast 227#options DIRECTED_BROADCAST # allow broadcasts through routers 228#options ISO,TPIP # OSI networking 229#options EON # OSI tunneling over IP 230#options NETATALK # AppleTalk (over Ethernet) protocol 231options NTP # Network Time Protocol in-kernel support 232#options PPS_SYNC # Add serial line synchronization for NTP 233options PFIL_HOOKS # Add pfil(9) packet filter hooks 234options IPFILTER_LOG # Add ipmon(8) logging for ipfilter device 235options IPFILTER_LOOKUP # ippool(8) support 236options IPFILTER_COMPAT # Compat for IP-Filter 237#options IPFILTER_DEFAULT_BLOCK # block all packets by default 238options PPP_BSDCOMP # Add BSD compression to ppp device 239options PPP_DEFLATE # Add deflate (libz) compression to ppp device 240options PPP_FILTER # Add active filters for ppp (via bpf) 241 242#options ALTQ # Manipulate network interfaces' output queues 243#options ALTQ_BLUE # Stochastic Fair Blue 244#options ALTQ_CBQ # Class-Based Queueing 245#options ALTQ_CDNR # Diffserv Traffic Conditioner 246#options ALTQ_FIFOQ # First-In First-Out Queue 247#options ALTQ_FLOWVALVE # RED/flow-valve (red-penalty-box) 248#options ALTQ_HFSC # Hierarchical Fair Service Curve 249#options ALTQ_LOCALQ # Local queueing discipline 250#options ALTQ_PRIQ # Priority Queueing 251#options ALTQ_RED # Random Early Detection 252#options ALTQ_RIO # RED with IN/OUT 253#options ALTQ_WFQ # Weighted Fair Queueing 254 255 256 257#### Main bus and CPU .. all systems. 258mainbus0 at root 259cpu0 at mainbus0 260cpuunit0 at mainbus0 # sun4d 261cpuunit* at mainbus0 # sun4d 262cpu0 at cpuunit0 # sun4d 263 264#### SX rendering engine found in SS20 and SS10SX 265sx0 at mainbus0 266 267#### Bus types found on SPARC systems. 268 269sbus0 at mainbus0 # sun4c 270obio0 at mainbus0 # sun4 and sun4m 271sparcvme0 at mainbus0 # sun4 272iommu0 at mainbus0 # sun4m 273sbus0 at iommu0 # sun4m 274sparcvme0 at iommu0 # sun4m 275vme0 at sparcvme0 # MI VME attachment 276bootbus0 at cpuunit0 # sun4d 277bootbus* at cpuunit? # sun4d 278 279## SBus expander box 280xbox* at sbus? slot ? offset ? 281sbus* at xbox? 282 283## SBus to PCMCIA bridge 284nell* at sbus? slot ? offset ? # PCMCIA bridge 285pcmcia* at nell? 286tslot* at sbus? slot ? offset ? # PCMCIA bridge (tadpole 3gx) 287pcmcia* at tslot? 288 289#### Standard system devices -- all required for a given architecture 290 291## Auxiliary system registers on sun4c and sun4m 292auxreg0 at mainbus0 # sun4c 293auxreg0 at obio0 # sun4m 294auxiotwo0 at obio0 # only on Tadpole SPARCbook. 295 296## Power status and control register on Sun4m systems 297power0 at obio0 298 299## Mostek clock found on 4/300, sun4c, sun4m and sun4d systems. 300## The Mostek clock NVRAM is the "eeprom" on sun4/300 systems. 301clock0 at mainbus0 # sun4c 302clock0 at obio0 # sun4m 303clock0 at obio0 addr 0xf2000000 # sun4/300 304clock0 at bootbus0 # sun4d 305 306## Intersil clock found on 4/100 and 4/200 systems. 307oclock0 at obio0 addr 0xf3000000 # sun4/200 308oclock0 at obio0 addr 0x03000000 # sun4/100 309 310## Memory error registers. 311memreg0 at mainbus0 # sun4c 312memreg0 at obio0 # sun4m 313memreg0 at obio0 addr 0xf4000000 # sun4/200 and sun4/300 314memreg0 at obio0 addr 0x04000000 # sun4/100 315 316## ECC memory control 317eccmemctl0 at mainbus0 # sun4m 318 319## Timer chip found on 4/300, sun4c, and sun4m systems. 320timer0 at mainbus0 # sun4c 321timer0 at obio0 # sun4m 322timer0 at obio0 addr 0xef000000 # sun4/300 323 324## EEPROM found on 4/100 and 4/200 systems. Note that the 4/300 325## doesn't use this driver; the `EEPROM' is in the NVRAM on the 326## Mostek clock chip on 4/300 systems. 327eeprom0 at obio0 addr 0xf2000000 # sun4/200 328eeprom0 at obio0 addr 0x02000000 # sun4/100 329 330 331#### Serial port configuration 332 333## Zilog 8530 serial chips. Each has two-channels. 334## zs0 is ttya and ttyb. zs1 is the keyboard and mouse. 335zs0 at mainbus0 # sun4c 336zs0 at obio0 # sun4m 337zs0 at obio0 addr 0xf1000000 level 12 # sun4/200 and sun4/300 338zs0 at obio0 addr 0x01000000 level 12 # sun4/100 339zs0 at bootbus0 # sun4d 340zstty0 at zs0 channel 0 # ttya 341zstty1 at zs0 channel 1 # ttyb 342 343zs1 at mainbus0 # sun4c 344zs1 at obio0 # sun4m 345zs1 at obio0 addr 0xf0000000 level 12 # sun4/200 and sun4/300 346zs1 at obio0 addr 0x00000000 level 12 # sun4/100 347zs1 at bootbus0 # sun4d 348 349# old kbd and mouse attachments 350#kbd0 at zs1 channel 0 # keyboard 351#ms0 at zs1 channel 1 # mouse 352zstty* at zs? 353 354# these are for wscons 355kbd0 at zstty? 356ms0 at zstty? 357wskbd* at wskbddev? 358wsmouse* at wsmousedev? 359 360zs2 at obio0 addr 0xe0000000 level 12 # sun4/300 361zstty2 at zs2 channel 0 # ttyc 362zstty3 at zs2 channel 1 # ttyd 363 364zs* at bootbus? # sun4d 365zstty* at zs? 366 367## NS16x50 serial chips and clones. Present on the 368## Sun JavaStation-1 and Tadpole SPARCbook 3 369com* at obio0 # sun4m 370 371# Parallel port. 372bpp* at sbus? slot? offset ? 373 374## Magma Serial/Parallel driver 375magma* at sbus? slot ? offset ? 376mtty* at magma? 377mbpp* at magma? 378 379## SUNW,spif Serial/Parallel driver 380spif* at sbus? slot ? offset ? 381stty* at spif? 382sbpp* at spif? 383 384## PCMCIA serial interfaces 385#com* at pcmcia? 386#pcmcom* at pcmcia? 387#com* at pcmcom? 388 389#### Disk controllers and disks 390 391# 392 393## The following flags may be set for the NCR53c94 based esp driver: 394## bits 0-7: disable disconnect/reselect for the corresponding target 395## bits 8-15: disable synchronous negotiation for target [bit-8] 396 397## sun4/300, sun4c, sun4m on-board SCSI, and FSBE/S SBus SCSI cards. 398## Both `dma' and `esp' are needed in all cases. 399## Two kinds of additional SBus SCSI interfaces are available. One uses 400## "esp at sbus" like the sun4c on-board; the other uses "esp at dma". 401 402## sun4/300 SCSI - an NCR53c94 or equivalent behind 403## an LSI Logic DMA controller 404 405dma0 at obio0 addr 0xfa001000 level 4 # sun4/300 406esp0 at obio0 addr 0xfa000000 level 4 flags 0x0000 # sun4/300 407 408dma0 at sbus0 slot ? offset ? # sun4c/sun4m 409esp0 at sbus0 slot ? offset ? flags 0x0000 # sun4c 410esp0 at dma0 flags 0x0000 # sun4m 411 412# FSBE/S SCSI & SunSwift Sbus FAS366 413dma* at sbus? slot ? offset ? # SBus 414esp* at sbus? slot ? offset ? flags 0x0000 # SBus 415esp* at dma? flags 0x0000 # SBus 416 417scsibus* at esp? 418 419## Qlogic ISP SBus SCSI Card 420isp* at sbus? slot ? offset ? 421scsibus* at isp? 422 423## NCR5380-based "Sun SCSI 3" VME SCSI controller. 424## This driver has several flags which may be enabled by OR'ing 425## the values and using the "flags" directive. 426## Valid flags are: 427## 428## 0x01 Use DMA (may be polled) 429## 0x02 Use DMA completion interrupts 430## 0x04 Allow disconnect/reselect 431## 432## E.g. the following would enable DMA, interrupts, and reselect: 433## si0 at vme0 addr 0x200000 irq 3 vect 0x40 flags 0x07 434## 435## By default, DMA is enabled in the driver. 436 437si0 at vme0 addr 0x200000 irq 2 vect 0x40 438scsibus* at si? 439 440## NCR5380-based "SCSI Weird" on-board SCSI interface found 441## on sun4/100 systems. The flags are the same as the "si" 442## controller. Note, while DMA is enabled by default, only 443## polled DMA works at this time, and reselects do not work 444## on this particular controller. 445 446sw0 at obio0 addr 0x0a000000 level 3 447scsibus* at sw? 448 449## PCMCIA SCSI controllers 450#aic* at pcmcia? 451#spc* at pcmcia? 452#scsibus* at aic? 453#scsibus* at spc? 454 455 456## These entries find devices on all SCSI busses and assign 457## unit numbers dynamically. 458sd* at scsibus? target ? lun ? # SCSI disks 459st* at scsibus? target ? lun ? # SCSI tapes 460cd* at scsibus? target ? lun ? # SCSI CD-ROMs 461ch* at scsibus? target ? lun ? # SCSI changer devices 462ss* at scsibus? target ? lun ? # SCSI scanners 463ses* at scsibus? target ? lun ? # SCSI SES/SAF-TE 464uk* at scsibus? target ? lun ? # unknown SCSI 465 466 467## Xylogics 753 or 7053 VME SMD disk controllers and disks, found 468## on sun4 systems. 469xdc0 at vme0 addr 0xee80 irq 3 vect 0x44 470xdc1 at vme0 addr 0xee90 irq 3 vect 0x45 471xdc2 at vme0 addr 0xeea0 irq 3 vect 0x46 472xdc3 at vme0 addr 0xeeb0 irq 3 vect 0x47 473xd* at xdc? drive ? 474 475## Xylogics 451 or 451 VME SMD disk controllers and disks, found 476## on sun4 systems. 477xyc0 at vme0 addr 0xee40 irq 3 vect 0x48 478xyc1 at vme0 addr 0xee48 irq 3 vect 0x49 479xy* at xyc? drive ? 480 481 482## Floppy controller and drive found on SPARCstations. 483 484fdc0 at mainbus0 # sun4c controller 485fdc0 at obio0 # sun4m controller 486fd* at fdc0 # the drive itself 487 488## PCMCIA IDE controllers 489#wdc* at pcmcia? 490#atabus* at ata? 491#wd* at atabus? drive ? flags 0x0000 492 493## A disk-like interface to files. Can be used to create floppy, CD, 494## miniroot images, etc. 495 496pseudo-device vnd 497#options VND_COMPRESSION # compressed vnd(4) 498 499## Concatenated and striped disks; with this, you can create a software-based 500## disk array similar to a "RAID 0" setup. See ccd(4). 501 502pseudo-device ccd 4 503 504## Cryptographic disk devices; See cgd(4) 505 506#pseudo-device cgd 4 507 508## RAIDframe disk driver: software RAID driver. See raid(4). 509 510pseudo-device raid 8 511options RAID_AUTOCONFIG # auto-configuration of RAID components 512# Options to enable various other RAIDframe RAID types. 513# options RF_INCLUDE_EVENODD=1 514# options RF_INCLUDE_RAID5_RS=1 515# options RF_INCLUDE_PARITYLOGGING=1 516# options RF_INCLUDE_CHAINDECLUSTER=1 517# options RF_INCLUDE_INTERDECLUSTER=1 518# options RF_INCLUDE_PARITY_DECLUSTERING=1 519# options RF_INCLUDE_PARITY_DECLUSTERING_DS=1 520 521 522## Memory disk device, used on boot floppies with compressed 523## kernel-plus-root-disk images. 524 525#pseudo-device md 526 527 528#### Network interfaces 529 530## LANCE Ethernet - an AMD 7990 LANCE behind specialized DMA glue 531## Three flavors of additional SBus ethernets are available. One attaches 532## directly like the sun4c on-board, one uses the ledma device like the 533## sun4m on-board, and one uses the lebuffer device. 534 535le0 at obio0 addr 0xf9000000 level 6 # sun4/300 536le0 at sbus0 slot ? offset ? # sun4c on-board 537ledma0 at sbus0 slot ? offset ? # sun4m on-board 538le0 at ledma0 # sun4m on-board 539le* at sbus? slot ? offset ? # SBus 540ledma* at sbus? slot ? offset ? # SBus 541le* at ledma? # SBus 542lebuffer0 at sbus? slot ? offset ? # SBus 543le0 at lebuffer? # SBus 544lebuffer* at sbus? slot ? offset ? # SBus 545le* at lebuffer? # SBus 546 547 548## sun4/100 and sun4/200 Ethernet - an Intel 82586 on-board 549## or on a Multibus/VME card. 550ie0 at obio0 addr 0xf6000000 level 6 # sun4/200 on-board 551ie0 at obio0 addr 0x06000000 level 6 # sun4/100 on-board 552## VME: the first [addr,len] pair specifies the device registers; 553## the second pair specifies the on-board memory buffer 554ie1 at vme0 addr 0xe88000,0xe00000 len -1,0x40000 irq 3 vect 0x75 555ie2 at vme0 addr 0x31ff02,0x300000 len -1,0x40000 irq 3 vect 0x76 556ie3 at vme0 addr 0x35ff02,0x300000 len -1,0x40000 irq 3 vect 0x77 557ie4 at vme0 addr 0x2dff02,0x200000 len -1,0x40000 irq 3 vect 0x7c 558 559## Quad Ethernet Controller with BigMac (be, 10/100MBd) and Mace Ethernet 560## (qe, 10MBd) attached. 561qec* at sbus? slot ? offset ? # Quad Ethernet Controller 562be* at qec? # BigMac Ethernet (10/100MBd) 563qe* at qec? # Mace Ethernet (10MBd) 564 565## Happy Meal Ethernet 566hme* at sbus? slot ? offset ? 567 568# midway ATM 569en0 at sbus? slot ? offset ? 570 571# PCMCIA ethernet devices 572#ep* at pcmcia? 573#mbe* at pcmcia? 574#ne* at pcmcia? 575#sm* at pcmcia? 576 577## PCMCIA wavelan card 578#wi* at pcmcia? function ? # Lucent WaveLan IEEE (802.11) 579 580# MII/PHY support 581exphy* at mii? phy ? # 3Com internal PHYs 582icsphy* at mii? phy ? # Integrated Circuit Systems ICS189x 583inphy* at mii? phy ? # Intel 82555 PHYs 584lxtphy* at mii? phy ? # Level One LXT-970 PHYs 585nsphy* at mii? phy ? # NS83840 PHYs 586qsphy* at mii? phy ? # Quality Semiconductor QS6612 PHYs 587sqphy* at mii? phy ? # Seeq 80220/80221/80223 PHYs 588tlphy* at mii? phy ? # ThunderLAN PHYs 589ukphy* at mii? phy ? # generic unknown PHYs 590 591## Loopback network interface; required 592pseudo-device loop 593 594## SLIP and CSLIP interfaces, for IP over a serial line. 595pseudo-device sl 596 597## PPP, the successor to SLIP. See pppd(8). 598pseudo-device ppp 599 600## PPP over Ethernet (RFC 2516) 601pseudo-device pppoe 602 603## Starmode Radio IP, a special hardware network device. 604#pseudo-device strip 605 606## Network "tunnel" device, allowing protocol stacks to run in the userland. 607## This is used by the third-party user-mode "ppp" program, and others. 608pseudo-device tun 609pseudo-device tap # virtual Ethernet 610 611## Generic L3 over IP tunnel 612#pseudo-device gre # generic L3 over IP tunnel 613 614## Berkeley Packet Filter, required to run RARPD. A generic C-language 615## interface that allows selective examining of incoming packets. 616pseudo-device bpfilter 617 618#pseudo-device carp # Common Address Redundancy Protocol 619 620## IP Filter, used in firewall and NAT applications. See ipnat(8) for 621## one example of the use of the IP Filter. 622pseudo-device ipfilter 623 624## for IPv6 625pseudo-device gif # IPv[46] over IPv[46] tunnel (RFC1933) 626#pseudo-device faith # IPv[46] tcp relay translation i/f 627pseudo-device stf # 6to4 IPv6 over IPv4 encapsulation 628 629## IEEE 802.1Q Virtual LAN encapsulation, see vlan(4). 630pseudo-device vlan 631 632## Simple inter-network traffic bridging 633pseudo-device bridge 634#options BRIDGE_IPF # bridge uses IP/IPv6 pfil hooks too 635pseudo-device agr # IEEE 802.3ad link aggregation 636 637## accept filters 638pseudo-device accf_data # "dataready" accept filter 639pseudo-device accf_http # "httpready" accept filter 640 641#### Audio and video devices 642 643## /dev/audio support (`audioamd' plus `audio') 644## 645audioamd0 at mainbus0 # sun4c 646audioamd0 at obio0 # sun4m 647audioamd0 at sbus0 slot ? offset ? # sun4m 648 649audiocs0 at sbus0 slot ? offset ? # SUNW,CS4231 650 651#options DBRI_DEBUG # noisy debug output from the dbri driver 652#options DBRI_BIG_BUFFER # use bigger DMA buffers, for slow CPUs 653dbri* at sbus? slot ? offset ? # SUNW,DBRI[s3|e] 654 655audio* at audiobus? 656 657## Sun "bwtwo" black and white framebuffer, found on sun4, sun4c, and sun4m 658## systems. If your sun4 system has a cgfour installed in the P4 slot, 659## the P4 entries for "bwtwo" will attach to the overlay plane of the 660## "cgfour". 661 662bwtwo0 at sbus0 slot ? offset ? # sun4c and sun4m 663bwtwo* at sbus? slot ? offset ? # 664bwtwo0 at obio0 addr 0xfd000000 level 4 # sun4/200 665bwtwo0 at obio0 addr 0xfb300000 level 4 # sun4/300 in P4 slot 666bwtwo0 at obio0 addr 0x0b300000 level 4 # sun4/100 in P4 slot 667 668## Sun "cgtwo" VME color framebuffer 669# XXX no wsdisplay support 670#cgtwo0 at vme0 addr 0x400000 irq ? vect 0xa8 671 672## Sun "cgthree" Sbus color framebuffer 673cgthree0 at sbus? slot ? offset ? 674cgthree* at sbus? slot ? offset ? 675 676## Sun "cgfour" color framebuffer with overlay plane. See above comment 677## regarding overlay plane. 678# XXX no wsdisplay support 679#cgfour0 at obio0 addr 0xfb300000 level 4 # sun4/300 P4 680#cgfour0 at obio0 addr 0x0b300000 level 4 # sun4/100 P4 681 682## Sun "cgsix" accelerated color framebuffer. 683cgsix0 at sbus? slot ? offset ? 684cgsix* at sbus? slot ? offset ? 685cgsix0 at obio0 addr 0xfb000000 level 4 # sun4/300 P4 686cgsix0 at obio0 addr 0x0b000000 level 4 # sun4/100 P4 687 688## Sun "cgeight" 24-bit framebuffer 689# XXX no wsdisplay support 690#cgeight0 at obio0 addr 0xfb300000 level 4 # sun4/300 P4 691#cgeight0 at obio0 addr 0x0b300000 level 4 # sun4/100 P4 692 693## Sun "tcx" accelerated color framebuffer. 694# there can be only one 695tcx0 at sbus? slot ? offset ? 696 697## Sun CG12 / Matrox SG3 accelerated 24bit framebuffer 698## runs monochrome only for now 699cgtwelve* at sbus? slot ? offset ? 700 701# Sun "cgfourteen" accelerated 24-bit framebuffer. 702cgfourteen* at obio0 # sun4m 703 704# P9100-based display on Tadpole SPARCbook 3. 705pnozz0 at sbus? slot ? offset ? 706# the SPARCbook 3 hardware docs say that accesses to P9100 registers need to be 707# 'latched in' but at least my 3GX works happily without 708# Enable it by default since we don't know which hardware really needs it. 709options PNOZZ_USE_LATCH 710 711# Sun ZX/Leo 24-bit framebuffer 712zx* at sbus? slot ? offset ? 713 714# Fujitsu AG-10e accelerated graphics 8/24-bit board 715agten* at sbus? slot ? offset ? 716 717# generic framebuffer console 718genfb* at sbus? slot ? offset ? 719 720# make sure wsdisplay0 is the console 721wsdisplay0 at wsemuldisplaydev? console 1 722wsdisplay* at wsemuldisplaydev? 723 724#### Other device configuration 725 726# Tadpole microcontroller 727tctrl0 at obio0 728 729# Aurora Personality Chip (APC) on SPARCstation-4/5 730# Not enabled by default as it may hang some systems 731#apc* at sbus? slot ? offset ? 732 733## Pseudo ttys, required for network logins and programs like screen. 734 735pseudo-device pty # pseudo-terminals 736 737## Random device, used to implement /dev/random (a source of random noise), 738## and generate randomness for some kernel formulae. 739 740 741# a pseudo device needed for Coda # also needs CODA (above) 742pseudo-device vcoda 4 # coda minicache <-> venus comm. 743 744pseudo-device clockctl # user control of clock subsystem 745pseudo-device ksyms # /dev/ksyms 746#pseudo-device pf # PF packet filter 747#pseudo-device pflog # PF log if 748pseudo-device fss # file system snapshot device 749pseudo-device wsmux # mouse and keyboard multiplexor 750pseudo-device wsfont 751pseudo-device putter # for puffs and pud 752 753#options FILEASSOC # fileassoc(9) 754 755# Veriexec 756# 757# a pseudo device needed for veriexec 758#pseudo-device veriexec 1 759# 760# Uncomment the fingerprint methods below that are desired. Note that 761# removing fingerprint methods will have almost no impact on the kernel 762# code size. 763# 764#options VERIFIED_EXEC_FP_RMD160 765#options VERIFIED_EXEC_FP_SHA256 766#options VERIFIED_EXEC_FP_SHA384 767#options VERIFIED_EXEC_FP_SHA512 768#options VERIFIED_EXEC_FP_SHA1 769#options VERIFIED_EXEC_FP_MD5 770 771#options PAX_MPROTECT=0 # PaX mprotect(2) restrictions 772 # (for static binaries only for now) 773