GENERIC revision 1.243
1# $NetBSD: GENERIC,v 1.243 2014/03/24 14:15:38 szptvlfn Exp $ 2# 3# GENERIC machine description file 4# 5# This machine description file is used to generate the default NetBSD 6# kernel. The generic kernel does not include all options, subsystems 7# and device drivers, but should be useful for most applications. 8# 9# The machine description file can be customised for your specific 10# machine to reduce the kernel size and improve its performance. 11# 12# For further information on compiling NetBSD kernels, see the config(8) 13# man page. 14# 15# For further information on hardware support for this architecture, see 16# the intro(4) man page. For further information about kernel options 17# for this architecture, see the options(4) man page. For an explanation 18# of each device driver in this file see the section 4 man page for the 19# device. 20 21include "arch/sparc/conf/std.sparc" 22 23options INCLUDE_CONFIG_FILE # embed config file in kernel binary 24 25#ident "GENERIC-$Revision: 1.243 $" 26 27maxusers 32 28 29## System kernel configuration. See options(4) for more detail. 30 31 32# Options for variants of the Sun SPARC architecure. 33# We currently support three architecture types; at least one is required. 34options SUN4 # sun4/100, sun4/200, sun4/300 35options SUN4C # sun4c - SS1, 1+, 2, ELC, SLC, IPC, IPX, etc. 36options SUN4M # sun4m - SS10, SS20, Classic, etc. 37options SUN4D # sun4d - SS1000, SC2000 38 39options SUN4_MMU3L # sun4/400 3-level MMU 40 41## System options specific to the sparc machine type 42 43# Blink the power LED on some machines to indicate the system load. 44#options BLINK 45 46## Use a faster console than the PROM's slow drawing routines. Not needed 47## for headless (no framebuffer) machines. 48## These is obsolete for wscons kernels 49#options RASTERCONSOLE # fast rasterop console 50#options RASTERCONSOLE_FGCOL=WSCOL_BLACK 51#options RASTERCONSOLE_BGCOL=WSCOL_WHITE 52 53# wscons stuff 54#options WSEMUL_SUN 55options WSEMUL_VT100 56options WSDISPLAY_COMPAT_RAWKBD 57options WSDISPLAY_CUSTOM_OUTPUT 58options WS_DEFAULT_FG=WSCOL_BLACK 59options WS_DEFAULT_BG=WSCOL_LIGHT_WHITE 60options WS_KERNEL_FG=WSCOL_GREEN 61options WS_KERNEL_BG=WSCOL_LIGHT_WHITE 62options WSDISPLAY_COMPAT_PCVT 63options WSDISPLAY_COMPAT_SYSCONS 64options WSDISPLAY_COMPAT_USL # wsconscfg VT handling 65 66options WSDISPLAY_SCROLLSUPPORT 67 68# generic options vlid for both wscons and RASTERCONSOLE 69options FONT_GALLANT12x22 # the console font 70options FONT_BOLD8x16 # a somewhat smaller font 71 72#### System options that are the same for all ports 73 74## Root device configuration: change the ?'s if you are going to use a 75## nonstandard root partition (other than where the kernel is booted from) 76## and/or nonstandard root type (not ffs or nfs). Normally this can be 77## automagically determined at boot time. 78 79config netbsd root on ? type ? 80 81## System call tracing (see ktrace(1)). 82options KTRACE 83 84## Collect statistics on kernel malloc's and free's. This does have a 85## significant performance hit on slower machines, so it is intended for 86## diagnostic use only. 87#options KMEMSTATS 88 89## System V compatible IPC subsystem. (msgctl(2), semctl(2), and shmctl(2)) 90options SYSVMSG # System V message queues 91options SYSVSEM # System V semaphores 92options SYSVSHM # System V shared memory 93 94options MODULAR # new style module(7) framework 95 96options USERCONF # userconf(4) support 97#options PIPE_SOCKETPAIR # smaller, but slower pipe(2) 98options SYSCTL_INCLUDE_DESCR # Include sysctl descriptions in kernel 99 100# Enable experimental buffer queue strategy for better responsiveness under 101# high disk I/O load. Use it with caution - it's not proven to be stable yet. 102#options BUFQ_READPRIO 103#options BUFQ_PRIOCSCAN 104 105## NFS boot options; tries DHCP/BOOTP then BOOTPARAM 106options NFS_BOOT_BOOTPARAM 107#options NFS_BOOT_BOOTP 108options NFS_BOOT_DHCP 109 110#### Debugging options 111 112## The DDB in-kernel debugger runs at panic (unless DDB_ONPANIC=0), or at 113## serial console break or keyboard reset, where the PROM would normally 114## intercept. DDB_HISTORY_SIZE adds up/down arrow command history. 115options DDB # kernel dynamic debugger 116options DDB_HISTORY_SIZE=100 # enable history editing in DDB 117#options DDB_ONPANIC=1 # see also sysctl(7): `ddb.onpanic' 118 119## You may also use gdb, on another computer connected to this machine over 120## a serial port. Both KGDB_DEV and KGDB_DEVRATE should be specified; 121## KGDB_DEV is a dev_t encoded device number of the serial port to use, where 122## the minor device number encodes the PROM enumeration of the serial ports, 123## i.e.: 124## 0xc00 = ttya, 0xc01 = ttyb, 0xc02 = ttyc, 0xc03 = ttyd. 125## (Note: ttyc and ttyd are available only on some sun4 models) 126#options KGDB # support for kernel gdb 127#options KGDB_DEV=0xc01 # kgdb device number (this is `ttyb') 128#options KGDB_DEVRATE=38400 # baud rate 129 130 131## Compile the kernel with debugging symbols (`netbsd.gdb' is the debug file), 132## such that gdb(1) can be used on a kernel coredump. 133 134#makeoptions DEBUG="-g" 135 136 137## Adds code to the kernel that does internal consistency checks, and will 138## cause the kernel to panic if corruption of internal data structures 139## is detected. 140#options DIAGNOSTIC # extra kernel sanity checking 141 142## Enable (possibly expensive) debugging code that may also display messages 143## on the system console 144#options DEBUG 145#options LOCKDEBUG 146#options SYSCALL_DEBUG 147 148## Make SCSI error messages more verbose when explaining their meanings. 149options SCSIVERBOSE 150 151options MIIVERBOSE # verbose PHY autoconfig messages 152 153## `INSECURE' turns off the kernel security level (securelevel = 0 always). 154## This allows writing to /dev/mem, loading kernel modules while multi-user, 155## and other insecurities good only for development work. Do not use this 156## option on a production machine. 157#options INSECURE 158 159## `FDSCRIPTS' allows non-readable but executable scripts by providing a 160## pre-opened opaque file to the script interpreter. `SETUIDSCRIPTS', 161## which implies FDSCRIPTS, allows scripts to be set-user-id using the same 162## opaque file mechanism. Perl calls this "secure setuid scripts." 163 164#options FDSCRIPTS 165#options SETUIDSCRIPTS 166 167## Options for compatibility with previous releases foreign system binaries. 168## In the cases of COMPAT_SUNOS and COMPAT_SVR4, you may need to set up 169## additional user-level utilities or system configuration files. See 170## compat_sunos(8) and compat_svr4(8). 171 172options COMPAT_43 # 4.3BSD system interfaces 173options COMPAT_10 # NetBSD 1.0 binary compatibility 174options COMPAT_11 # NetBSD 1.1 binary compatibility 175options COMPAT_12 # NetBSD 1.2 binary compatibility 176options COMPAT_13 # NetBSD 1.3 binary compatibility 177options COMPAT_14 # NetBSD 1.4 binary compatibility 178options COMPAT_15 # NetBSD 1.5 binary compatibility 179options COMPAT_16 # NetBSD 1.6 binary compatibility 180options COMPAT_20 # NetBSD 2.0 binary compatibility 181options COMPAT_30 # NetBSD 3.0 binary compatibility 182options COMPAT_40 # NetBSD 4.0 binary compatibility 183options COMPAT_50 # NetBSD 5.0 binary compatibility 184options COMPAT_60 # NetBSD 6.0 compatibility. 185options COMPAT_SUNOS # SunOS 4.x binary compatibility 186options COMPAT_SVR4 # SunOS 5.x binary compatibility 187options COMPAT_BSDPTY # /dev/[pt]ty?? ptys. 188 189## File systems. You probably need at least one of FFS or NFS. 190file-system FFS # Berkeley Fast Filesystem 191file-system NFS # Sun NFS-compatible filesystem client 192file-system KERNFS # kernel data-structure filesystem 193file-system NULLFS # NULL layered filesystem 194file-system OVERLAY # overlay file system 195file-system MFS # memory-based filesystem 196file-system FDESC # user file descriptor filesystem 197file-system UMAPFS # uid/gid remapping filesystem 198file-system LFS # Log-based filesystem (still experimental) 199file-system PUFFS # Userspace file systems (e.g. ntfs-3g & sshfs) 200file-system PROCFS # /proc 201file-system CD9660 # ISO 9660 + Rock Ridge file system 202file-system UNION # union file system 203file-system MSDOSFS # MS-DOS FAT filesystem(s). 204file-system CODA # Coda File System; also needs vcoda (below) 205file-system PTYFS # /dev/pts/N support 206file-system TMPFS # Efficient memory file-system 207#file-system UDF # experimental - OSTA UDF CD/DVD file-system 208 209## File system options. 210options NFSSERVER # Sun NFS-compatible filesystem server 211options QUOTA # FFS quotas 212#options FFS_EI # FFS Endian Independent support 213options WAPBL # File system journaling support 214#options UFS_DIRHASH # UFS Large Directory Hashing - Experimental 215#options FFS_NO_SNAPSHOT # No FFS snapshot support 216 217## Network protocol support. In most environments, INET is required. 218options INET # IP (Internet Protocol) v4 219options INET6 # IPV6 220#options IPSEC # IP security 221#options IPSEC_DEBUG # debug for IP security 222#options GATEWAY # packet forwarding ("router switch") 223#options MROUTING # packet forwarding of multicast packets 224#options PIM # Protocol Independent Multicast 225#options DIRECTED_BROADCAST # allow broadcasts through routers 226#options NETATALK # AppleTalk (over Ethernet) protocol 227options NTP # Network Time Protocol in-kernel support 228#options PPS_SYNC # Add serial line synchronization for NTP 229options IPFILTER_LOG # Add ipmon(8) logging for ipfilter device 230options IPFILTER_LOOKUP # ippool(8) support 231options IPFILTER_COMPAT # Compat for IP-Filter 232#options IPFILTER_DEFAULT_BLOCK # block all packets by default 233options PPP_BSDCOMP # Add BSD compression to ppp device 234options PPP_DEFLATE # Add deflate (libz) compression to ppp device 235options PPP_FILTER # Add active filters for ppp (via bpf) 236 237#options ALTQ # Manipulate network interfaces' output queues 238#options ALTQ_BLUE # Stochastic Fair Blue 239#options ALTQ_CBQ # Class-Based Queueing 240#options ALTQ_CDNR # Diffserv Traffic Conditioner 241#options ALTQ_FIFOQ # First-In First-Out Queue 242#options ALTQ_FLOWVALVE # RED/flow-valve (red-penalty-box) 243#options ALTQ_HFSC # Hierarchical Fair Service Curve 244#options ALTQ_LOCALQ # Local queueing discipline 245#options ALTQ_PRIQ # Priority Queueing 246#options ALTQ_RED # Random Early Detection 247#options ALTQ_RIO # RED with IN/OUT 248#options ALTQ_WFQ # Weighted Fair Queueing 249 250 251 252#### Main bus and CPU .. all systems. 253mainbus0 at root 254cpu0 at mainbus0 255cpuunit0 at mainbus0 # sun4d 256cpuunit* at mainbus0 # sun4d 257cpu0 at cpuunit0 # sun4d 258 259#### SX rendering engine found in SS20 and SS10SX 260sx0 at mainbus0 261 262#### Bus types found on SPARC systems. 263 264sbus0 at mainbus0 # sun4c 265obio0 at mainbus0 # sun4 and sun4m 266sparcvme0 at mainbus0 # sun4 267iommu0 at mainbus0 # sun4m 268sbus0 at iommu0 # sun4m 269sparcvme0 at iommu0 # sun4m 270vme0 at sparcvme0 # MI VME attachment 271bootbus0 at cpuunit0 # sun4d 272bootbus* at cpuunit? # sun4d 273 274## SBus expander box 275xbox* at sbus? slot ? offset ? 276sbus* at xbox? 277 278## SBus to PCMCIA bridge 279nell* at sbus? slot ? offset ? # PCMCIA bridge 280pcmcia* at nell? 281tslot* at sbus? slot ? offset ? # PCMCIA bridge (tadpole 3gx) 282pcmcia* at tslot? 283 284#### Standard system devices -- all required for a given architecture 285 286## Auxiliary system registers on sun4c and sun4m 287auxreg0 at mainbus0 # sun4c 288auxreg0 at obio0 # sun4m 289auxiotwo0 at obio0 # only on Tadpole SPARCbook. 290 291## Power status and control register on Sun4m systems 292power0 at obio0 293 294## Mostek clock found on 4/300, sun4c, sun4m and sun4d systems. 295## The Mostek clock NVRAM is the "eeprom" on sun4/300 systems. 296clock0 at mainbus0 # sun4c 297clock0 at obio0 # sun4m 298clock0 at obio0 addr 0xf2000000 # sun4/300 299clock0 at bootbus0 # sun4d 300 301## Intersil clock found on 4/100 and 4/200 systems. 302oclock0 at obio0 addr 0xf3000000 # sun4/200 303oclock0 at obio0 addr 0x03000000 # sun4/100 304 305## Memory error registers. 306memreg0 at mainbus0 # sun4c 307memreg0 at obio0 # sun4m 308memreg0 at obio0 addr 0xf4000000 # sun4/200 and sun4/300 309memreg0 at obio0 addr 0x04000000 # sun4/100 310 311## ECC memory control 312eccmemctl0 at mainbus0 # sun4m 313 314## Timer chip found on 4/300, sun4c, and sun4m systems. 315timer0 at mainbus0 # sun4c 316timer0 at obio0 # sun4m 317timer0 at obio0 addr 0xef000000 # sun4/300 318 319## EEPROM found on 4/100 and 4/200 systems. Note that the 4/300 320## doesn't use this driver; the `EEPROM' is in the NVRAM on the 321## Mostek clock chip on 4/300 systems. 322eeprom0 at obio0 addr 0xf2000000 # sun4/200 323eeprom0 at obio0 addr 0x02000000 # sun4/100 324 325 326#### Serial port configuration 327 328## Zilog 8530 serial chips. Each has two-channels. 329## zs0 is ttya and ttyb. zs1 is the keyboard and mouse. 330zs0 at mainbus0 # sun4c 331zs0 at obio0 # sun4m 332zs0 at obio0 addr 0xf1000000 level 12 # sun4/200 and sun4/300 333zs0 at obio0 addr 0x01000000 level 12 # sun4/100 334zs0 at bootbus0 # sun4d 335zstty0 at zs0 channel 0 # ttya 336zstty1 at zs0 channel 1 # ttyb 337 338zs1 at mainbus0 # sun4c 339zs1 at obio0 # sun4m 340zs1 at obio0 addr 0xf0000000 level 12 # sun4/200 and sun4/300 341zs1 at obio0 addr 0x00000000 level 12 # sun4/100 342zs1 at bootbus0 # sun4d 343 344# old kbd and mouse attachments 345#kbd0 at zs1 channel 0 # keyboard 346#ms0 at zs1 channel 1 # mouse 347zstty* at zs? 348 349# these are for wscons 350kbd0 at zstty? 351ms0 at zstty? 352wskbd* at wskbddev? 353wsmouse* at wsmousedev? 354 355zs2 at obio0 addr 0xe0000000 level 12 # sun4/300 356zstty2 at zs2 channel 0 # ttyc 357zstty3 at zs2 channel 1 # ttyd 358 359zs* at bootbus? # sun4d 360zstty* at zs? 361 362## NS16x50 serial chips and clones. Present on the 363## Sun JavaStation-1 and Tadpole SPARCbook 3 364com* at obio0 # sun4m 365 366# Parallel port. 367bpp* at sbus? slot? offset ? 368 369## Magma Serial/Parallel driver 370magma* at sbus? slot ? offset ? 371mtty* at magma? 372mbpp* at magma? 373 374## SUNW,spif Serial/Parallel driver 375spif* at sbus? slot ? offset ? 376stty* at spif? 377sbpp* at spif? 378 379## PCMCIA serial interfaces 380#com* at pcmcia? 381#pcmcom* at pcmcia? 382#com* at pcmcom? 383 384#### Disk controllers and disks 385 386# 387 388## The following flags may be set for the NCR53c94 based esp driver: 389## bits 0-7: disable disconnect/reselect for the corresponding target 390## bits 8-15: disable synchronous negotiation for target [bit-8] 391 392## sun4/300, sun4c, sun4m on-board SCSI, and FSBE/S SBus SCSI cards. 393## Both `dma' and `esp' are needed in all cases. 394## Two kinds of additional SBus SCSI interfaces are available. One uses 395## "esp at sbus" like the sun4c on-board; the other uses "esp at dma". 396 397## sun4/300 SCSI - an NCR53c94 or equivalent behind 398## an LSI Logic DMA controller 399 400dma0 at obio0 addr 0xfa001000 level 4 # sun4/300 401esp0 at obio0 addr 0xfa000000 level 4 flags 0x0000 # sun4/300 402 403dma0 at sbus0 slot ? offset ? # sun4c/sun4m 404esp0 at sbus0 slot ? offset ? flags 0x0000 # sun4c 405esp0 at dma0 flags 0x0000 # sun4m 406 407# FSBE/S SCSI & SunSwift Sbus FAS366 408dma* at sbus? slot ? offset ? # SBus 409esp* at sbus? slot ? offset ? flags 0x0000 # SBus 410esp* at dma? flags 0x0000 # SBus 411 412scsibus* at esp? 413 414## Qlogic ISP SBus SCSI Card 415isp* at sbus? slot ? offset ? 416scsibus* at isp? 417 418## NCR5380-based "Sun SCSI 3" VME SCSI controller. 419## This driver has several flags which may be enabled by OR'ing 420## the values and using the "flags" directive. 421## Valid flags are: 422## 423## 0x01 Use DMA (may be polled) 424## 0x02 Use DMA completion interrupts 425## 0x04 Allow disconnect/reselect 426## 427## E.g. the following would enable DMA, interrupts, and reselect: 428## si0 at vme0 addr 0x200000 irq 3 vect 0x40 flags 0x07 429## 430## By default, DMA is enabled in the driver. 431 432si0 at vme0 addr 0x200000 irq 2 vect 0x40 433scsibus* at si? 434 435## NCR5380-based "SCSI Weird" on-board SCSI interface found 436## on sun4/100 systems. The flags are the same as the "si" 437## controller. Note, while DMA is enabled by default, only 438## polled DMA works at this time, and reselects do not work 439## on this particular controller. 440 441sw0 at obio0 addr 0x0a000000 level 3 442scsibus* at sw? 443 444## PCMCIA SCSI controllers 445#aic* at pcmcia? 446#spc* at pcmcia? 447#scsibus* at aic? 448#scsibus* at spc? 449 450 451## These entries find devices on all SCSI busses and assign 452## unit numbers dynamically. 453sd* at scsibus? target ? lun ? # SCSI disks 454st* at scsibus? target ? lun ? # SCSI tapes 455cd* at scsibus? target ? lun ? # SCSI CD-ROMs 456ch* at scsibus? target ? lun ? # SCSI changer devices 457ss* at scsibus? target ? lun ? # SCSI scanners 458ses* at scsibus? target ? lun ? # SCSI SES/SAF-TE 459uk* at scsibus? target ? lun ? # unknown SCSI 460 461 462## Xylogics 753 or 7053 VME SMD disk controllers and disks, found 463## on sun4 systems. 464xdc0 at vme0 addr 0xee80 irq 3 vect 0x44 465xdc1 at vme0 addr 0xee90 irq 3 vect 0x45 466xdc2 at vme0 addr 0xeea0 irq 3 vect 0x46 467xdc3 at vme0 addr 0xeeb0 irq 3 vect 0x47 468xd* at xdc? drive ? 469 470## Xylogics 451 or 451 VME SMD disk controllers and disks, found 471## on sun4 systems. 472xyc0 at vme0 addr 0xee40 irq 3 vect 0x48 473xyc1 at vme0 addr 0xee48 irq 3 vect 0x49 474xy* at xyc? drive ? 475 476 477## Floppy controller and drive found on SPARCstations. 478 479fdc0 at mainbus0 # sun4c controller 480fdc0 at obio0 # sun4m controller 481fd* at fdc0 # the drive itself 482 483## PCMCIA IDE controllers 484#wdc* at pcmcia? 485#atabus* at ata? 486#wd* at atabus? drive ? flags 0x0000 487 488## A disk-like interface to files. Can be used to create floppy, CD, 489## miniroot images, etc. 490 491pseudo-device vnd 492#options VND_COMPRESSION # compressed vnd(4) 493 494## Concatenated and striped disks; with this, you can create a software-based 495## disk array similar to a "RAID 0" setup. See ccd(4). 496 497pseudo-device ccd 498 499## Cryptographic disk devices; See cgd(4) 500 501#pseudo-device cgd 502 503## RAIDframe disk driver: software RAID driver. See raid(4). 504 505pseudo-device raid 506options RAID_AUTOCONFIG # auto-configuration of RAID components 507# Options to enable various other RAIDframe RAID types. 508# options RF_INCLUDE_EVENODD=1 509# options RF_INCLUDE_RAID5_RS=1 510# options RF_INCLUDE_PARITYLOGGING=1 511# options RF_INCLUDE_CHAINDECLUSTER=1 512# options RF_INCLUDE_INTERDECLUSTER=1 513# options RF_INCLUDE_PARITY_DECLUSTERING=1 514# options RF_INCLUDE_PARITY_DECLUSTERING_DS=1 515 516 517## Memory disk device, used on boot floppies with compressed 518## kernel-plus-root-disk images. 519 520#pseudo-device md 521 522 523#### Network interfaces 524 525## LANCE Ethernet - an AMD 7990 LANCE behind specialized DMA glue 526## Three flavors of additional SBus ethernets are available. One attaches 527## directly like the sun4c on-board, one uses the ledma device like the 528## sun4m on-board, and one uses the lebuffer device. 529 530le0 at obio0 addr 0xf9000000 level 6 # sun4/300 531le0 at sbus0 slot ? offset ? # sun4c on-board 532ledma0 at sbus0 slot ? offset ? # sun4m on-board 533le0 at ledma0 # sun4m on-board 534le* at sbus? slot ? offset ? # SBus 535ledma* at sbus? slot ? offset ? # SBus 536le* at ledma? # SBus 537lebuffer0 at sbus? slot ? offset ? # SBus 538le0 at lebuffer? # SBus 539lebuffer* at sbus? slot ? offset ? # SBus 540le* at lebuffer? # SBus 541 542 543## sun4/100 and sun4/200 Ethernet - an Intel 82586 on-board 544## or on a Multibus/VME card. 545ie0 at obio0 addr 0xf6000000 level 6 # sun4/200 on-board 546ie0 at obio0 addr 0x06000000 level 6 # sun4/100 on-board 547## VME: the first [addr,len] pair specifies the device registers; 548## the second pair specifies the on-board memory buffer 549ie1 at vme0 addr 0xe88000,0xe00000 len -1,0x40000 irq 3 vect 0x75 550ie2 at vme0 addr 0x31ff02,0x300000 len -1,0x40000 irq 3 vect 0x76 551ie3 at vme0 addr 0x35ff02,0x300000 len -1,0x40000 irq 3 vect 0x77 552ie4 at vme0 addr 0x2dff02,0x200000 len -1,0x40000 irq 3 vect 0x7c 553 554## Quad Ethernet Controller with BigMac (be, 10/100MBd) and Mace Ethernet 555## (qe, 10MBd) attached. 556qec* at sbus? slot ? offset ? # Quad Ethernet Controller 557be* at qec? # BigMac Ethernet (10/100MBd) 558qe* at qec? # Mace Ethernet (10MBd) 559 560## Happy Meal Ethernet 561hme* at sbus? slot ? offset ? 562 563# midway ATM 564en0 at sbus? slot ? offset ? 565 566# PCMCIA ethernet devices 567#ep* at pcmcia? 568#mbe* at pcmcia? 569#ne* at pcmcia? 570#sm* at pcmcia? 571 572## PCMCIA wavelan card 573#wi* at pcmcia? function ? # Lucent WaveLan IEEE (802.11) 574 575# MII/PHY support 576exphy* at mii? phy ? # 3Com internal PHYs 577icsphy* at mii? phy ? # Integrated Circuit Systems ICS189x 578inphy* at mii? phy ? # Intel 82555 PHYs 579lxtphy* at mii? phy ? # Level One LXT-970 PHYs 580nsphy* at mii? phy ? # NS83840 PHYs 581qsphy* at mii? phy ? # Quality Semiconductor QS6612 PHYs 582sqphy* at mii? phy ? # Seeq 80220/80221/80223 PHYs 583tlphy* at mii? phy ? # ThunderLAN PHYs 584ukphy* at mii? phy ? # generic unknown PHYs 585 586## Loopback network interface; required 587pseudo-device loop 588 589## SLIP and CSLIP interfaces, for IP over a serial line. 590pseudo-device sl 591 592## PPP, the successor to SLIP. See pppd(8). 593pseudo-device ppp 594 595## PPP over Ethernet (RFC 2516) 596pseudo-device pppoe 597 598## Starmode Radio IP, a special hardware network device. 599#pseudo-device strip 600 601## Network "tunnel" device, allowing protocol stacks to run in the userland. 602## This is used by the third-party user-mode "ppp" program, and others. 603pseudo-device tun 604pseudo-device tap # virtual Ethernet 605 606## Generic L3 over IP tunnel 607#pseudo-device gre # generic L3 over IP tunnel 608 609## Berkeley Packet Filter, required to run RARPD. A generic C-language 610## interface that allows selective examining of incoming packets. 611pseudo-device bpfilter 612 613#pseudo-device carp # Common Address Redundancy Protocol 614 615## IP Filter, used in firewall and NAT applications. See ipnat(8) for 616## one example of the use of the IP Filter. 617pseudo-device ipfilter 618 619## for IPv6 620pseudo-device gif # IPv[46] over IPv[46] tunnel (RFC1933) 621#pseudo-device faith # IPv[46] tcp relay translation i/f 622pseudo-device stf # 6to4 IPv6 over IPv4 encapsulation 623 624## IEEE 802.1Q Virtual LAN encapsulation, see vlan(4). 625pseudo-device vlan 626 627## Simple inter-network traffic bridging 628pseudo-device bridge 629#options BRIDGE_IPF # bridge uses IP/IPv6 pfil hooks too 630pseudo-device agr # IEEE 802.3ad link aggregation 631 632## accept filters 633pseudo-device accf_data # "dataready" accept filter 634pseudo-device accf_http # "httpready" accept filter 635 636#### Audio and video devices 637 638## /dev/audio support (`audioamd' plus `audio') 639## 640audioamd0 at mainbus0 # sun4c 641audioamd0 at obio0 # sun4m 642audioamd0 at sbus0 slot ? offset ? # sun4m 643 644audiocs0 at sbus0 slot ? offset ? # SUNW,CS4231 645 646#options DBRI_DEBUG # noisy debug output from the dbri driver 647#options DBRI_BIG_BUFFER # use bigger DMA buffers, for slow CPUs 648dbri* at sbus? slot ? offset ? # SUNW,DBRI[s3|e] 649 650audio* at audiobus? 651 652## Sun "bwtwo" black and white framebuffer, found on sun4, sun4c, and sun4m 653## systems. If your sun4 system has a cgfour installed in the P4 slot, 654## the P4 entries for "bwtwo" will attach to the overlay plane of the 655## "cgfour". 656 657bwtwo0 at sbus0 slot ? offset ? # sun4c and sun4m 658bwtwo* at sbus? slot ? offset ? # 659bwtwo0 at obio0 addr 0xfd000000 level 4 # sun4/200 660bwtwo0 at obio0 addr 0xfb300000 level 4 # sun4/300 in P4 slot 661bwtwo0 at obio0 addr 0x0b300000 level 4 # sun4/100 in P4 slot 662 663## Sun "cgtwo" VME color framebuffer 664# XXX no wsdisplay support 665#cgtwo0 at vme0 addr 0x400000 irq ? vect 0xa8 666 667## Sun "cgthree" Sbus color framebuffer 668cgthree0 at sbus? slot ? offset ? 669cgthree* at sbus? slot ? offset ? 670 671## Sun "cgfour" color framebuffer with overlay plane. See above comment 672## regarding overlay plane. 673# XXX no wsdisplay support 674#cgfour0 at obio0 addr 0xfb300000 level 4 # sun4/300 P4 675#cgfour0 at obio0 addr 0x0b300000 level 4 # sun4/100 P4 676 677## Sun "cgsix" accelerated color framebuffer. 678cgsix0 at sbus? slot ? offset ? 679cgsix* at sbus? slot ? offset ? 680cgsix0 at obio0 addr 0xfb000000 level 4 # sun4/300 P4 681cgsix0 at obio0 addr 0x0b000000 level 4 # sun4/100 P4 682 683## Sun "cgeight" 24-bit framebuffer 684# XXX no wsdisplay support 685#cgeight0 at obio0 addr 0xfb300000 level 4 # sun4/300 P4 686#cgeight0 at obio0 addr 0x0b300000 level 4 # sun4/100 P4 687 688## Sun "tcx" accelerated color framebuffer. 689# there can be only one 690tcx0 at sbus? slot ? offset ? 691 692## Sun CG12 / Matrox SG3 accelerated 24bit framebuffer 693## runs monochrome only for now 694cgtwelve* at sbus? slot ? offset ? 695 696# Sun "cgfourteen" accelerated 24-bit framebuffer. 697cgfourteen* at obio0 # sun4m 698 699# P9100-based display on Tadpole SPARCbook 3. 700pnozz0 at sbus? slot ? offset ? 701# the SPARCbook 3 hardware docs say that accesses to P9100 registers need to be 702# 'latched in' but at least my 3GX works happily without 703# Enable it by default since we don't know which hardware really needs it. 704options PNOZZ_USE_LATCH 705 706# Sun ZX/Leo 24-bit framebuffer 707zx* at sbus? slot ? offset ? 708 709# Fujitsu AG-10e accelerated graphics 8/24-bit board 710agten* at sbus? slot ? offset ? 711 712# generic framebuffer console 713genfb* at sbus? slot ? offset ? 714 715# make sure wsdisplay0 is the console 716wsdisplay0 at wsemuldisplaydev? console 1 717wsdisplay* at wsemuldisplaydev? 718 719#### Other device configuration 720 721# Tadpole microcontroller 722tctrl0 at obio0 723 724# Aurora Personality Chip (APC) on SPARCstation-4/5 725# Not enabled by default as it may hang some systems 726#apc* at sbus? slot ? offset ? 727 728## Pseudo ttys, required for network logins and programs like screen. 729 730pseudo-device pty # pseudo-terminals 731 732## Random device, used to implement /dev/random (a source of random noise), 733## and generate randomness for some kernel formulae. 734 735 736# a pseudo device needed for Coda # also needs CODA (above) 737pseudo-device vcoda # coda minicache <-> venus comm. 738 739pseudo-device clockctl # user control of clock subsystem 740pseudo-device ksyms # /dev/ksyms 741#pseudo-device pf # PF packet filter 742#pseudo-device pflog # PF log if 743pseudo-device fss # file system snapshot device 744pseudo-device wsmux # mouse and keyboard multiplexor 745pseudo-device wsfont 746pseudo-device putter # for puffs and pud 747 748#options FILEASSOC # fileassoc(9) 749 750# Veriexec 751# 752# a pseudo device needed for veriexec 753#pseudo-device veriexec 754# 755# Uncomment the fingerprint methods below that are desired. Note that 756# removing fingerprint methods will have almost no impact on the kernel 757# code size. 758# 759#options VERIFIED_EXEC_FP_RMD160 760#options VERIFIED_EXEC_FP_SHA256 761#options VERIFIED_EXEC_FP_SHA384 762#options VERIFIED_EXEC_FP_SHA512 763#options VERIFIED_EXEC_FP_SHA1 764#options VERIFIED_EXEC_FP_MD5 765 766#options PAX_MPROTECT=0 # PaX mprotect(2) restrictions 767 # (for static binaries only for now) 768