GENERIC revision 1.248.2.1
1 # $NetBSD: GENERIC,v 1.248.2.1 2015/12/27 12:09:43 skrll Exp $ 2 # 3 # GENERIC machine description file 4 # 5 # This machine description file is used to generate the default NetBSD 6 # kernel. The generic kernel does not include all options, subsystems 7 # and device drivers, but should be useful for most applications. 8 # 9 # The machine description file can be customised for your specific 10 # machine to reduce the kernel size and improve its performance. 11 # 12 # For further information on compiling NetBSD kernels, see the config(8) 13 # man page. 14 # 15 # For further information on hardware support for this architecture, see 16 # the intro(4) man page. For further information about kernel options 17 # for this architecture, see the options(4) man page. For an explanation 18 # of each device driver in this file see the section 4 man page for the 19 # device. 20 21 include "arch/sparc/conf/std.sparc" 22 23 options INCLUDE_CONFIG_FILE # embed config file in kernel binary 24 25 #ident "GENERIC-$Revision: 1.248.2.1 $" 26 27 maxusers 32 28 29 ## System kernel configuration. See options(4) for more detail. 30 31 32 # Options for variants of the Sun SPARC architecure. 33 # We currently support three architecture types; at least one is required. 34 options SUN4 # sun4/100, sun4/200, sun4/300 35 options SUN4C # sun4c - SS1, 1+, 2, ELC, SLC, IPC, IPX, etc. 36 options SUN4M # sun4m - SS10, SS20, Classic, etc. 37 options SUN4D # sun4d - SS1000, SC2000 38 39 options SUN4_MMU3L # sun4/400 3-level MMU 40 41 ## System options specific to the sparc machine type 42 43 # Blink the power LED on some machines to indicate the system load. 44 #options BLINK 45 46 ## Use a faster console than the PROM's slow drawing routines. Not needed 47 ## for headless (no framebuffer) machines. 48 ## These is obsolete for wscons kernels 49 #options RASTERCONSOLE # fast rasterop console 50 #options RASTERCONSOLE_FGCOL=WSCOL_BLACK 51 #options RASTERCONSOLE_BGCOL=WSCOL_WHITE 52 53 # wscons stuff 54 #options WSEMUL_SUN 55 options WSEMUL_VT100 56 options WSDISPLAY_COMPAT_RAWKBD 57 options WSDISPLAY_CUSTOM_OUTPUT 58 options WS_DEFAULT_FG=WSCOL_BLACK 59 options WS_DEFAULT_BG=WSCOL_LIGHT_WHITE 60 options WS_KERNEL_FG=WSCOL_GREEN 61 options WS_KERNEL_BG=WSCOL_LIGHT_WHITE 62 options WSDISPLAY_COMPAT_PCVT 63 options WSDISPLAY_COMPAT_SYSCONS 64 options WSDISPLAY_COMPAT_USL # wsconscfg VT handling 65 66 options WSDISPLAY_SCROLLSUPPORT 67 68 # generic options vlid for both wscons and RASTERCONSOLE 69 options FONT_GALLANT12x22 # the console font 70 options FONT_BOLD8x16 # a somewhat smaller font 71 72 #### System options that are the same for all ports 73 74 ## Root device configuration: change the ?'s if you are going to use a 75 ## nonstandard root partition (other than where the kernel is booted from) 76 ## and/or nonstandard root type (not ffs or nfs). Normally this can be 77 ## automagically determined at boot time. 78 79 config netbsd root on ? type ? 80 81 ## System call tracing (see ktrace(1)). 82 options KTRACE 83 84 ## System V compatible IPC subsystem. (msgctl(2), semctl(2), and shmctl(2)) 85 options SYSVMSG # System V message queues 86 options SYSVSEM # System V semaphores 87 options SYSVSHM # System V shared memory 88 89 options MODULAR # new style module(7) framework 90 options MODULAR_DEFAULT_AUTOLOAD 91 92 options USERCONF # userconf(4) support 93 #options PIPE_SOCKETPAIR # smaller, but slower pipe(2) 94 options SYSCTL_INCLUDE_DESCR # Include sysctl descriptions in kernel 95 96 # Enable experimental buffer queue strategy for better responsiveness under 97 # high disk I/O load. Use it with caution - it's not proven to be stable yet. 98 #options BUFQ_READPRIO 99 #options BUFQ_PRIOCSCAN 100 101 ## NFS boot options; tries DHCP/BOOTP then BOOTPARAM 102 options NFS_BOOT_BOOTPARAM 103 #options NFS_BOOT_BOOTP 104 options NFS_BOOT_DHCP 105 106 #### Debugging options 107 108 ## The DDB in-kernel debugger runs at panic (unless DDB_ONPANIC=0), or at 109 ## serial console break or keyboard reset, where the PROM would normally 110 ## intercept. DDB_HISTORY_SIZE adds up/down arrow command history. 111 options DDB # kernel dynamic debugger 112 options DDB_HISTORY_SIZE=100 # enable history editing in DDB 113 #options DDB_ONPANIC=1 # see also sysctl(7): `ddb.onpanic' 114 115 ## You may also use gdb, on another computer connected to this machine over 116 ## a serial port. Both KGDB_DEV and KGDB_DEVRATE should be specified; 117 ## KGDB_DEV is a dev_t encoded device number of the serial port to use, where 118 ## the minor device number encodes the PROM enumeration of the serial ports, 119 ## i.e.: 120 ## 0xc00 = ttya, 0xc01 = ttyb, 0xc02 = ttyc, 0xc03 = ttyd. 121 ## (Note: ttyc and ttyd are available only on some sun4 models) 122 #options KGDB # support for kernel gdb 123 #options KGDB_DEV=0xc01 # kgdb device number (this is `ttyb') 124 #options KGDB_DEVRATE=38400 # baud rate 125 126 127 ## Compile the kernel with debugging symbols (`netbsd.gdb' is the debug file), 128 ## such that gdb(1) can be used on a kernel coredump. 129 130 #makeoptions DEBUG="-g" 131 132 133 ## Adds code to the kernel that does internal consistency checks, and will 134 ## cause the kernel to panic if corruption of internal data structures 135 ## is detected. 136 #options DIAGNOSTIC # extra kernel sanity checking 137 138 ## Enable (possibly expensive) debugging code that may also display messages 139 ## on the system console 140 #options DEBUG 141 #options LOCKDEBUG 142 #options SYSCALL_DEBUG 143 144 ## Make SCSI error messages more verbose when explaining their meanings. 145 options SCSIVERBOSE 146 147 options MIIVERBOSE # verbose PHY autoconfig messages 148 149 ## `INSECURE' turns off the kernel security level (securelevel = 0 always). 150 ## This allows writing to /dev/mem, loading kernel modules while multi-user, 151 ## and other insecurities good only for development work. Do not use this 152 ## option on a production machine. 153 #options INSECURE 154 155 ## `FDSCRIPTS' allows non-readable but executable scripts by providing a 156 ## pre-opened opaque file to the script interpreter. `SETUIDSCRIPTS', 157 ## which implies FDSCRIPTS, allows scripts to be set-user-id using the same 158 ## opaque file mechanism. Perl calls this "secure setuid scripts." 159 160 #options FDSCRIPTS 161 #options SETUIDSCRIPTS 162 163 ## Options for compatibility with previous releases foreign system binaries. 164 ## In the cases of COMPAT_SUNOS and COMPAT_SVR4, you may need to set up 165 ## additional user-level utilities or system configuration files. See 166 ## compat_sunos(8) and compat_svr4(8). 167 168 options COMPAT_43 # 4.3BSD system interfaces 169 options COMPAT_10 # NetBSD 1.0, 170 options COMPAT_11 # NetBSD 1.1, 171 options COMPAT_12 # NetBSD 1.2, 172 options COMPAT_13 # NetBSD 1.3, 173 options COMPAT_14 # NetBSD 1.4, 174 options COMPAT_15 # NetBSD 1.5, 175 options COMPAT_16 # NetBSD 1.6, 176 options COMPAT_20 # NetBSD 2.0, 177 options COMPAT_30 # NetBSD 3.0, 178 options COMPAT_40 # NetBSD 4.0, 179 options COMPAT_50 # NetBSD 5.0, 180 options COMPAT_60 # NetBSD 6.0, and 181 options COMPAT_70 # NetBSD 7.0 binary compatibility 182 options COMPAT_SUNOS # SunOS 4.x binary compatibility 183 options COMPAT_SVR4 # SunOS 5.x binary compatibility 184 options COMPAT_BSDPTY # /dev/[pt]ty?? ptys. 185 186 ## File systems. You probably need at least one of FFS or NFS. 187 file-system FFS # Berkeley Fast Filesystem 188 file-system NFS # Sun NFS-compatible filesystem client 189 file-system KERNFS # kernel data-structure filesystem 190 file-system NULLFS # NULL layered filesystem 191 file-system OVERLAY # overlay file system 192 file-system MFS # memory-based filesystem 193 file-system FDESC # user file descriptor filesystem 194 file-system UMAPFS # uid/gid remapping filesystem 195 file-system LFS # Log-based filesystem (still experimental) 196 file-system PUFFS # Userspace file systems (e.g. ntfs-3g & sshfs) 197 file-system PROCFS # /proc 198 file-system CD9660 # ISO 9660 + Rock Ridge file system 199 file-system UNION # union file system 200 file-system MSDOSFS # MS-DOS FAT filesystem(s). 201 file-system CODA # Coda File System; also needs vcoda (below) 202 file-system PTYFS # /dev/pts/N support 203 file-system TMPFS # Efficient memory file-system 204 #file-system UDF # experimental - OSTA UDF CD/DVD file-system 205 206 ## File system options. 207 options NFSSERVER # Sun NFS-compatible filesystem server 208 options QUOTA # FFS quotas 209 #options FFS_EI # FFS Endian Independent support 210 options WAPBL # File system journaling support 211 #options UFS_DIRHASH # UFS Large Directory Hashing - Experimental 212 #options FFS_NO_SNAPSHOT # No FFS snapshot support 213 options UFS_EXTATTR # Extended attribute support for UFS1 214 215 ## Network protocol support. In most environments, INET is required. 216 options INET # IP (Internet Protocol) v4 217 options INET6 # IPV6 218 #options IPSEC # IP security 219 #options IPSEC_DEBUG # debug for IP security 220 #options GATEWAY # packet forwarding ("router switch") 221 #options MROUTING # packet forwarding of multicast packets 222 #options PIM # Protocol Independent Multicast 223 #options DIRECTED_BROADCAST # allow broadcasts through routers 224 #options NETATALK # AppleTalk (over Ethernet) protocol 225 options NTP # Network Time Protocol in-kernel support 226 #options PPS_SYNC # Add serial line synchronization for NTP 227 options IPFILTER_LOG # Add ipmon(8) logging for ipfilter device 228 options IPFILTER_LOOKUP # ippool(8) support 229 options IPFILTER_COMPAT # Compat for IP-Filter 230 #options IPFILTER_DEFAULT_BLOCK # block all packets by default 231 options PPP_BSDCOMP # Add BSD compression to ppp device 232 options PPP_DEFLATE # Add deflate (libz) compression to ppp device 233 options PPP_FILTER # Add active filters for ppp (via bpf) 234 235 #options ALTQ # Manipulate network interfaces' output queues 236 #options ALTQ_BLUE # Stochastic Fair Blue 237 #options ALTQ_CBQ # Class-Based Queueing 238 #options ALTQ_CDNR # Diffserv Traffic Conditioner 239 #options ALTQ_FIFOQ # First-In First-Out Queue 240 #options ALTQ_FLOWVALVE # RED/flow-valve (red-penalty-box) 241 #options ALTQ_HFSC # Hierarchical Fair Service Curve 242 #options ALTQ_LOCALQ # Local queueing discipline 243 #options ALTQ_PRIQ # Priority Queueing 244 #options ALTQ_RED # Random Early Detection 245 #options ALTQ_RIO # RED with IN/OUT 246 #options ALTQ_WFQ # Weighted Fair Queueing 247 248 249 250 #### Main bus and CPU .. all systems. 251 mainbus0 at root 252 cpu0 at mainbus0 253 cpuunit0 at mainbus0 # sun4d 254 cpuunit* at mainbus0 # sun4d 255 cpu0 at cpuunit0 # sun4d 256 257 #### SX rendering engine found in SS20 and SS10SX 258 sx0 at mainbus0 259 260 #### Bus types found on SPARC systems. 261 262 sbus0 at mainbus0 # sun4c 263 obio0 at mainbus0 # sun4 and sun4m 264 sparcvme0 at mainbus0 # sun4 265 iommu0 at mainbus0 # sun4m 266 sbus0 at iommu0 # sun4m 267 sparcvme0 at iommu0 # sun4m 268 vme0 at sparcvme0 # MI VME attachment 269 bootbus0 at cpuunit0 # sun4d 270 bootbus* at cpuunit? # sun4d 271 272 ## SBus expander box 273 xbox* at sbus? slot ? offset ? 274 sbus* at xbox? 275 276 ## SBus to PCMCIA bridge 277 nell* at sbus? slot ? offset ? # PCMCIA bridge 278 pcmcia* at nell? 279 tslot* at sbus? slot ? offset ? # PCMCIA bridge (tadpole 3gx) 280 pcmcia* at tslot? 281 282 #### Standard system devices -- all required for a given architecture 283 284 ## Auxiliary system registers on sun4c and sun4m 285 auxreg0 at mainbus0 # sun4c 286 auxreg0 at obio0 # sun4m 287 auxiotwo0 at obio0 # only on Tadpole SPARCbook. 288 289 ## Power status and control register on Sun4m systems 290 power0 at obio0 291 292 ## Mostek clock found on 4/300, sun4c, sun4m and sun4d systems. 293 ## The Mostek clock NVRAM is the "eeprom" on sun4/300 systems. 294 clock0 at mainbus0 # sun4c 295 clock0 at obio0 # sun4m 296 clock0 at obio0 addr 0xf2000000 # sun4/300 297 clock0 at bootbus0 # sun4d 298 299 ## Intersil clock found on 4/100 and 4/200 systems. 300 oclock0 at obio0 addr 0xf3000000 # sun4/200 301 oclock0 at obio0 addr 0x03000000 # sun4/100 302 303 ## Memory error registers. 304 memreg0 at mainbus0 # sun4c 305 memreg0 at obio0 # sun4m 306 memreg0 at obio0 addr 0xf4000000 # sun4/200 and sun4/300 307 memreg0 at obio0 addr 0x04000000 # sun4/100 308 309 ## ECC memory control 310 eccmemctl0 at mainbus0 # sun4m 311 312 ## Timer chip found on 4/300, sun4c, and sun4m systems. 313 timer0 at mainbus0 # sun4c 314 timer0 at obio0 # sun4m 315 timer0 at obio0 addr 0xef000000 # sun4/300 316 317 ## EEPROM found on 4/100 and 4/200 systems. Note that the 4/300 318 ## doesn't use this driver; the `EEPROM' is in the NVRAM on the 319 ## Mostek clock chip on 4/300 systems. 320 eeprom0 at obio0 addr 0xf2000000 # sun4/200 321 eeprom0 at obio0 addr 0x02000000 # sun4/100 322 323 324 #### Serial port configuration 325 326 ## Zilog 8530 serial chips. Each has two-channels. 327 ## zs0 is ttya and ttyb. zs1 is the keyboard and mouse. 328 zs0 at mainbus0 # sun4c 329 zs0 at obio0 # sun4m 330 zs0 at obio0 addr 0xf1000000 level 12 # sun4/200 and sun4/300 331 zs0 at obio0 addr 0x01000000 level 12 # sun4/100 332 zs0 at bootbus0 # sun4d 333 zstty0 at zs0 channel 0 # ttya 334 zstty1 at zs0 channel 1 # ttyb 335 336 zs1 at mainbus0 # sun4c 337 zs1 at obio0 # sun4m 338 zs1 at obio0 addr 0xf0000000 level 12 # sun4/200 and sun4/300 339 zs1 at obio0 addr 0x00000000 level 12 # sun4/100 340 zs1 at bootbus0 # sun4d 341 342 # old kbd and mouse attachments 343 #kbd0 at zs1 channel 0 # keyboard 344 #ms0 at zs1 channel 1 # mouse 345 zstty* at zs? 346 347 # these are for wscons 348 kbd0 at zstty? 349 ms0 at zstty? 350 wskbd* at wskbddev? 351 wsmouse* at wsmousedev? 352 353 zs2 at obio0 addr 0xe0000000 level 12 # sun4/300 354 zstty2 at zs2 channel 0 # ttyc 355 zstty3 at zs2 channel 1 # ttyd 356 357 zs* at bootbus? # sun4d 358 zstty* at zs? 359 360 ## NS16x50 serial chips and clones. Present on the 361 ## Sun JavaStation-1 and Tadpole SPARCbook 3 362 com* at obio0 # sun4m 363 364 # Parallel port. 365 bpp* at sbus? slot? offset ? 366 367 ## Magma Serial/Parallel driver 368 magma* at sbus? slot ? offset ? 369 mtty* at magma? 370 mbpp* at magma? 371 372 ## SUNW,spif Serial/Parallel driver 373 spif* at sbus? slot ? offset ? 374 stty* at spif? 375 sbpp* at spif? 376 377 ## PCMCIA serial interfaces 378 #com* at pcmcia? 379 #pcmcom* at pcmcia? 380 #com* at pcmcom? 381 382 #### Disk controllers and disks 383 384 # 385 386 ## The following flags may be set for the NCR53c94 based esp driver: 387 ## bits 0-7: disable disconnect/reselect for the corresponding target 388 ## bits 8-15: disable synchronous negotiation for target [bit-8] 389 390 ## sun4/300, sun4c, sun4m on-board SCSI, and FSBE/S SBus SCSI cards. 391 ## Both `dma' and `esp' are needed in all cases. 392 ## Two kinds of additional SBus SCSI interfaces are available. One uses 393 ## "esp at sbus" like the sun4c on-board; the other uses "esp at dma". 394 395 ## sun4/300 SCSI - an NCR53c94 or equivalent behind 396 ## an LSI Logic DMA controller 397 398 dma0 at obio0 addr 0xfa001000 level 4 # sun4/300 399 esp0 at obio0 addr 0xfa000000 level 4 flags 0x0000 # sun4/300 400 401 dma0 at sbus0 slot ? offset ? # sun4c/sun4m 402 esp0 at sbus0 slot ? offset ? flags 0x0000 # sun4c 403 esp0 at dma0 flags 0x0000 # sun4m 404 405 # FSBE/S SCSI & SunSwift Sbus FAS366 406 dma* at sbus? slot ? offset ? # SBus 407 esp* at sbus? slot ? offset ? flags 0x0000 # SBus 408 esp* at dma? flags 0x0000 # SBus 409 410 scsibus* at esp? 411 412 ## Qlogic ISP SBus SCSI Card 413 isp* at sbus? slot ? offset ? 414 scsibus* at isp? 415 416 ## NCR5380-based "Sun SCSI 3" VME SCSI controller. 417 ## This driver has several flags which may be enabled by OR'ing 418 ## the values and using the "flags" directive. 419 ## Valid flags are: 420 ## 421 ## 0x01 Use DMA (may be polled) 422 ## 0x02 Use DMA completion interrupts 423 ## 0x04 Allow disconnect/reselect 424 ## 425 ## E.g. the following would enable DMA, interrupts, and reselect: 426 ## si0 at vme0 addr 0x200000 irq 3 vect 0x40 flags 0x07 427 ## 428 ## By default, DMA is enabled in the driver. 429 430 si0 at vme0 addr 0x200000 irq 2 vect 0x40 431 scsibus* at si? 432 433 ## NCR5380-based "SCSI Weird" on-board SCSI interface found 434 ## on sun4/100 systems. The flags are the same as the "si" 435 ## controller. Note, while DMA is enabled by default, only 436 ## polled DMA works at this time, and reselects do not work 437 ## on this particular controller. 438 439 sw0 at obio0 addr 0x0a000000 level 3 440 scsibus* at sw? 441 442 ## PCMCIA SCSI controllers 443 #aic* at pcmcia? 444 #spc* at pcmcia? 445 #scsibus* at aic? 446 #scsibus* at spc? 447 448 449 ## These entries find devices on all SCSI busses and assign 450 ## unit numbers dynamically. 451 sd* at scsibus? target ? lun ? # SCSI disks 452 st* at scsibus? target ? lun ? # SCSI tapes 453 cd* at scsibus? target ? lun ? # SCSI CD-ROMs 454 ch* at scsibus? target ? lun ? # SCSI changer devices 455 ss* at scsibus? target ? lun ? # SCSI scanners 456 ses* at scsibus? target ? lun ? # SCSI SES/SAF-TE 457 uk* at scsibus? target ? lun ? # unknown SCSI 458 459 460 ## Xylogics 753 or 7053 VME SMD disk controllers and disks, found 461 ## on sun4 systems. 462 xdc0 at vme0 addr 0xee80 irq 3 vect 0x44 463 xdc1 at vme0 addr 0xee90 irq 3 vect 0x45 464 xdc2 at vme0 addr 0xeea0 irq 3 vect 0x46 465 xdc3 at vme0 addr 0xeeb0 irq 3 vect 0x47 466 xd* at xdc? drive ? 467 468 ## Xylogics 451 or 451 VME SMD disk controllers and disks, found 469 ## on sun4 systems. 470 xyc0 at vme0 addr 0xee40 irq 3 vect 0x48 471 xyc1 at vme0 addr 0xee48 irq 3 vect 0x49 472 xy* at xyc? drive ? 473 474 475 ## Floppy controller and drive found on SPARCstations. 476 477 fdc0 at mainbus0 # sun4c controller 478 fdc0 at obio0 # sun4m controller 479 fd* at fdc0 # the drive itself 480 481 ## PCMCIA IDE controllers 482 #wdc* at pcmcia? 483 #atabus* at ata? 484 #wd* at atabus? drive ? flags 0x0000 485 486 ## A disk-like interface to files. Can be used to create floppy, CD, 487 ## miniroot images, etc. 488 489 pseudo-device vnd 490 #options VND_COMPRESSION # compressed vnd(4) 491 492 ## Concatenated and striped disks; with this, you can create a software-based 493 ## disk array similar to a "RAID 0" setup. See ccd(4). 494 495 pseudo-device ccd 496 497 ## Cryptographic disk devices; See cgd(4) 498 499 #pseudo-device cgd 500 501 ## RAIDframe disk driver: software RAID driver. See raid(4). 502 503 pseudo-device raid 504 options RAID_AUTOCONFIG # auto-configuration of RAID components 505 # Options to enable various other RAIDframe RAID types. 506 # options RF_INCLUDE_EVENODD=1 507 # options RF_INCLUDE_RAID5_RS=1 508 # options RF_INCLUDE_PARITYLOGGING=1 509 # options RF_INCLUDE_CHAINDECLUSTER=1 510 # options RF_INCLUDE_INTERDECLUSTER=1 511 # options RF_INCLUDE_PARITY_DECLUSTERING=1 512 # options RF_INCLUDE_PARITY_DECLUSTERING_DS=1 513 514 515 ## Memory disk device, used on boot floppies with compressed 516 ## kernel-plus-root-disk images. 517 518 #pseudo-device md 519 520 521 #### Network interfaces 522 523 ## LANCE Ethernet - an AMD 7990 LANCE behind specialized DMA glue 524 ## Three flavors of additional SBus ethernets are available. One attaches 525 ## directly like the sun4c on-board, one uses the ledma device like the 526 ## sun4m on-board, and one uses the lebuffer device. 527 528 le0 at obio0 addr 0xf9000000 level 6 # sun4/300 529 le0 at sbus0 slot ? offset ? # sun4c on-board 530 ledma0 at sbus0 slot ? offset ? # sun4m on-board 531 le0 at ledma0 # sun4m on-board 532 le* at sbus? slot ? offset ? # SBus 533 ledma* at sbus? slot ? offset ? # SBus 534 le* at ledma? # SBus 535 lebuffer0 at sbus? slot ? offset ? # SBus 536 le0 at lebuffer? # SBus 537 lebuffer* at sbus? slot ? offset ? # SBus 538 le* at lebuffer? # SBus 539 540 541 ## sun4/100 and sun4/200 Ethernet - an Intel 82586 on-board 542 ## or on a Multibus/VME card. 543 ie0 at obio0 addr 0xf6000000 level 6 # sun4/200 on-board 544 ie0 at obio0 addr 0x06000000 level 6 # sun4/100 on-board 545 ## VME: the first [addr,len] pair specifies the device registers; 546 ## the second pair specifies the on-board memory buffer 547 ie1 at vme0 addr 0xe88000,0xe00000 len -1,0x40000 irq 3 vect 0x75 548 ie2 at vme0 addr 0x31ff02,0x300000 len -1,0x40000 irq 3 vect 0x76 549 ie3 at vme0 addr 0x35ff02,0x300000 len -1,0x40000 irq 3 vect 0x77 550 ie4 at vme0 addr 0x2dff02,0x200000 len -1,0x40000 irq 3 vect 0x7c 551 552 ## Quad Ethernet Controller with BigMac (be, 10/100MBd) and Mace Ethernet 553 ## (qe, 10MBd) attached. 554 qec* at sbus? slot ? offset ? # Quad Ethernet Controller 555 be* at qec? # BigMac Ethernet (10/100MBd) 556 qe* at qec? # Mace Ethernet (10MBd) 557 558 ## Happy Meal Ethernet 559 hme* at sbus? slot ? offset ? 560 561 # midway ATM 562 en0 at sbus? slot ? offset ? 563 564 # PCMCIA ethernet devices 565 #ep* at pcmcia? 566 #mbe* at pcmcia? 567 #ne* at pcmcia? 568 #sm* at pcmcia? 569 570 ## PCMCIA wavelan card 571 #wi* at pcmcia? function ? # Lucent WaveLan IEEE (802.11) 572 573 # MII/PHY support 574 exphy* at mii? phy ? # 3Com internal PHYs 575 icsphy* at mii? phy ? # Integrated Circuit Systems ICS189x 576 inphy* at mii? phy ? # Intel 82555 PHYs 577 lxtphy* at mii? phy ? # Level One LXT-970 PHYs 578 nsphy* at mii? phy ? # NS83840 PHYs 579 qsphy* at mii? phy ? # Quality Semiconductor QS6612 PHYs 580 sqphy* at mii? phy ? # Seeq 80220/80221/80223 PHYs 581 tlphy* at mii? phy ? # ThunderLAN PHYs 582 ukphy* at mii? phy ? # generic unknown PHYs 583 584 ## Loopback network interface; required 585 pseudo-device loop 586 587 ## SLIP and CSLIP interfaces, for IP over a serial line. 588 pseudo-device sl 589 590 ## PPP, the successor to SLIP. See pppd(8). 591 pseudo-device ppp 592 593 ## PPP over Ethernet (RFC 2516) 594 pseudo-device pppoe 595 596 ## Starmode Radio IP, a special hardware network device. 597 #pseudo-device strip 598 599 ## Network "tunnel" device, allowing protocol stacks to run in the userland. 600 ## This is used by the third-party user-mode "ppp" program, and others. 601 pseudo-device tun 602 pseudo-device tap # virtual Ethernet 603 604 ## Generic L3 over IP tunnel 605 #pseudo-device gre # generic L3 over IP tunnel 606 607 ## Berkeley Packet Filter, required to run RARPD. A generic C-language 608 ## interface that allows selective examining of incoming packets. 609 pseudo-device bpfilter 610 611 #pseudo-device carp # Common Address Redundancy Protocol 612 613 ## IP Filter, used in firewall and NAT applications. See ipnat(8) for 614 ## one example of the use of the IP Filter. 615 pseudo-device ipfilter 616 617 ## for IPv6 618 pseudo-device gif # IPv[46] over IPv[46] tunnel (RFC1933) 619 #pseudo-device faith # IPv[46] tcp relay translation i/f 620 pseudo-device stf # 6to4 IPv6 over IPv4 encapsulation 621 622 ## IEEE 802.1Q Virtual LAN encapsulation, see vlan(4). 623 pseudo-device vlan 624 625 ## Simple inter-network traffic bridging 626 pseudo-device bridge 627 #options BRIDGE_IPF # bridge uses IP/IPv6 pfil hooks too 628 pseudo-device agr # IEEE 802.3ad link aggregation 629 630 ## accept filters 631 pseudo-device accf_data # "dataready" accept filter 632 pseudo-device accf_http # "httpready" accept filter 633 634 #### Audio and video devices 635 636 ## /dev/audio support (`audioamd' plus `audio') 637 ## 638 audioamd0 at mainbus0 # sun4c 639 audioamd0 at obio0 # sun4m 640 audioamd0 at sbus0 slot ? offset ? # sun4m 641 642 audiocs0 at sbus0 slot ? offset ? # SUNW,CS4231 643 644 #options DBRI_DEBUG # noisy debug output from the dbri driver 645 #options DBRI_BIG_BUFFER # use bigger DMA buffers, for slow CPUs 646 dbri* at sbus? slot ? offset ? # SUNW,DBRI[s3|e] 647 648 audio* at audiobus? 649 650 ## Sun "bwtwo" black and white framebuffer, found on sun4, sun4c, and sun4m 651 ## systems. If your sun4 system has a cgfour installed in the P4 slot, 652 ## the P4 entries for "bwtwo" will attach to the overlay plane of the 653 ## "cgfour". 654 655 bwtwo0 at sbus0 slot ? offset ? # sun4c and sun4m 656 bwtwo* at sbus? slot ? offset ? # 657 bwtwo0 at obio0 addr 0xfd000000 level 4 # sun4/200 658 bwtwo0 at obio0 addr 0xfb300000 level 4 # sun4/300 in P4 slot 659 bwtwo0 at obio0 addr 0x0b300000 level 4 # sun4/100 in P4 slot 660 661 ## Sun "cgtwo" VME color framebuffer 662 # XXX no wsdisplay support 663 #cgtwo0 at vme0 addr 0x400000 irq ? vect 0xa8 664 665 ## Sun "cgthree" Sbus color framebuffer 666 cgthree0 at sbus? slot ? offset ? 667 cgthree* at sbus? slot ? offset ? 668 669 ## Sun "cgfour" color framebuffer with overlay plane. See above comment 670 ## regarding overlay plane. 671 # XXX no wsdisplay support 672 #cgfour0 at obio0 addr 0xfb300000 level 4 # sun4/300 P4 673 #cgfour0 at obio0 addr 0x0b300000 level 4 # sun4/100 P4 674 675 ## Sun "cgsix" accelerated color framebuffer. 676 cgsix0 at sbus? slot ? offset ? 677 cgsix* at sbus? slot ? offset ? 678 cgsix0 at obio0 addr 0xfb000000 level 4 # sun4/300 P4 679 cgsix0 at obio0 addr 0x0b000000 level 4 # sun4/100 P4 680 681 ## Sun "cgeight" 24-bit framebuffer 682 # XXX no wsdisplay support 683 #cgeight0 at obio0 addr 0xfb300000 level 4 # sun4/300 P4 684 #cgeight0 at obio0 addr 0x0b300000 level 4 # sun4/100 P4 685 686 ## Sun "tcx" accelerated color framebuffer. 687 # there can be only one 688 tcx0 at sbus? slot ? offset ? 689 690 ## Sun CG12 / Matrox SG3 accelerated 24bit framebuffer 691 ## runs monochrome only for now 692 cgtwelve* at sbus? slot ? offset ? 693 694 # Sun "cgfourteen" accelerated 24-bit framebuffer. 695 cgfourteen* at obio0 # sun4m 696 697 # P9100-based display on Tadpole SPARCbook 3. 698 pnozz0 at sbus? slot ? offset ? 699 # the SPARCbook 3 hardware docs say that accesses to P9100 registers need to be 700 # 'latched in' but at least my 3GX works happily without 701 # Enable it by default since we don't know which hardware really needs it. 702 options PNOZZ_USE_LATCH 703 704 # Sun ZX/Leo 24-bit framebuffer 705 zx* at sbus? slot ? offset ? 706 707 # Fujitsu AG-10e accelerated graphics 8/24-bit board 708 agten* at sbus? slot ? offset ? 709 710 # generic framebuffer console 711 genfb* at sbus? slot ? offset ? 712 713 # make sure wsdisplay0 is the console 714 wsdisplay0 at wsemuldisplaydev? console 1 715 wsdisplay* at wsemuldisplaydev? 716 717 #### Other device configuration 718 719 # Tadpole microcontroller 720 tctrl0 at obio0 721 722 # Aurora Personality Chip (APC) on SPARCstation-4/5 723 # Not enabled by default as it may hang some systems 724 #apc* at sbus? slot ? offset ? 725 726 ## Pseudo ttys, required for network logins and programs like screen. 727 728 pseudo-device pty # pseudo-terminals 729 730 ## Random device, used to implement /dev/random (a source of random noise), 731 ## and generate randomness for some kernel formulae. 732 733 734 # a pseudo device needed for Coda # also needs CODA (above) 735 pseudo-device vcoda # coda minicache <-> venus comm. 736 737 pseudo-device clockctl # user control of clock subsystem 738 pseudo-device ksyms # /dev/ksyms 739 #pseudo-device pf # PF packet filter 740 #pseudo-device pflog # PF log if 741 pseudo-device fss # file system snapshot device 742 pseudo-device wsmux # mouse and keyboard multiplexor 743 pseudo-device wsfont 744 pseudo-device putter # for puffs and pud 745 746 #options FILEASSOC # fileassoc(9) 747 748 # Veriexec 749 # 750 # a pseudo device needed for veriexec 751 #pseudo-device veriexec 752 # 753 # Uncomment the fingerprint methods below that are desired. Note that 754 # removing fingerprint methods will have almost no impact on the kernel 755 # code size. 756 # 757 #options VERIFIED_EXEC_FP_RMD160 758 #options VERIFIED_EXEC_FP_SHA256 759 #options VERIFIED_EXEC_FP_SHA384 760 #options VERIFIED_EXEC_FP_SHA512 761 #options VERIFIED_EXEC_FP_SHA1 762 #options VERIFIED_EXEC_FP_MD5 763 764 #options PAX_MPROTECT=0 # PaX mprotect(2) restrictions 765 # (for static binaries only for now) 766
Indexes created Thu Oct 23 22:10:10 GMT 2025