GENERIC revision 1.253
1# $NetBSD: GENERIC,v 1.253 2016/12/10 09:44:06 mrg Exp $ 2# 3# GENERIC machine description file 4# 5# This machine description file is used to generate the default NetBSD 6# kernel. The generic kernel does not include all options, subsystems 7# and device drivers, but should be useful for most applications. 8# 9# The machine description file can be customised for your specific 10# machine to reduce the kernel size and improve its performance. 11# 12# For further information on compiling NetBSD kernels, see the config(8) 13# man page. 14# 15# For further information on hardware support for this architecture, see 16# the intro(4) man page. For further information about kernel options 17# for this architecture, see the options(4) man page. For an explanation 18# of each device driver in this file see the section 4 man page for the 19# device. 20 21include "arch/sparc/conf/std.sparc" 22 23options INCLUDE_CONFIG_FILE # embed config file in kernel binary 24 25#ident "GENERIC-$Revision: 1.253 $" 26 27maxusers 32 28 29## System kernel configuration. See options(4) for more detail. 30 31 32# Options for variants of the Sun SPARC architecure. 33# We currently support three architecture types; at least one is required. 34options SUN4 # sun4/100, sun4/200, sun4/300 35options SUN4C # sun4c - SS1, 1+, 2, ELC, SLC, IPC, IPX, etc. 36options SUN4M # sun4m - SS10, SS20, Classic, etc. 37options SUN4D # sun4d - SS1000, SC2000 38 39options SUN4_MMU3L # sun4/400 3-level MMU 40 41## System options specific to the sparc machine type 42 43# Blink the power LED on some machines to indicate the system load. 44#options BLINK 45 46# wscons stuff 47#options WSEMUL_SUN 48options WSEMUL_VT100 49options WSDISPLAY_COMPAT_RAWKBD 50options WSDISPLAY_CUSTOM_OUTPUT 51options WS_DEFAULT_FG=WSCOL_BLACK 52options WS_DEFAULT_BG=WSCOL_LIGHT_WHITE 53options WS_KERNEL_FG=WSCOL_GREEN 54options WS_KERNEL_BG=WSCOL_LIGHT_WHITE 55options WSDISPLAY_COMPAT_PCVT 56options WSDISPLAY_COMPAT_SYSCONS 57options WSDISPLAY_COMPAT_USL # wsconscfg VT handling 58 59options WSDISPLAY_SCROLLSUPPORT 60 61options FONT_GALLANT12x22 # the console font 62options FONT_BOLD8x16 # a somewhat smaller font 63 64#### System options that are the same for all ports 65 66## Root device configuration: change the ?'s if you are going to use a 67## nonstandard root partition (other than where the kernel is booted from) 68## and/or nonstandard root type (not ffs or nfs). Normally this can be 69## automagically determined at boot time. 70 71config netbsd root on ? type ? 72 73## System call tracing (see ktrace(1)). 74options KTRACE 75 76## System V compatible IPC subsystem. (msgctl(2), semctl(2), and shmctl(2)) 77options SYSVMSG # System V message queues 78options SYSVSEM # System V semaphores 79options SYSVSHM # System V shared memory 80 81options MODULAR # new style module(7) framework 82options MODULAR_DEFAULT_AUTOLOAD 83 84options USERCONF # userconf(4) support 85#options PIPE_SOCKETPAIR # smaller, but slower pipe(2) 86options SYSCTL_INCLUDE_DESCR # Include sysctl descriptions in kernel 87 88# Enable experimental buffer queue strategy for better responsiveness under 89# high disk I/O load. Use it with caution - it's not proven to be stable yet. 90#options BUFQ_READPRIO 91#options BUFQ_PRIOCSCAN 92 93## NFS boot options; tries DHCP/BOOTP then BOOTPARAM 94options NFS_BOOT_BOOTPARAM 95#options NFS_BOOT_BOOTP 96options NFS_BOOT_DHCP 97 98#### Debugging options 99 100## The DDB in-kernel debugger runs at panic (unless DDB_ONPANIC=0), or at 101## serial console break or keyboard reset, where the PROM would normally 102## intercept. DDB_HISTORY_SIZE adds up/down arrow command history. 103options DDB # kernel dynamic debugger 104options DDB_HISTORY_SIZE=100 # enable history editing in DDB 105#options DDB_ONPANIC=1 # see also sysctl(7): `ddb.onpanic' 106 107## You may also use gdb, on another computer connected to this machine over 108## a serial port. Both KGDB_DEV and KGDB_DEVRATE should be specified; 109## KGDB_DEV is a dev_t encoded device number of the serial port to use, where 110## the minor device number encodes the PROM enumeration of the serial ports, 111## i.e.: 112## 0xc00 = ttya, 0xc01 = ttyb, 0xc02 = ttyc, 0xc03 = ttyd. 113## (Note: ttyc and ttyd are available only on some sun4 models) 114#options KGDB # support for kernel gdb 115#options KGDB_DEV=0xc01 # kgdb device number (this is `ttyb') 116#options KGDB_DEVRATE=38400 # baud rate 117 118 119## Compile the kernel with debugging symbols (`netbsd.gdb' is the debug file), 120## such that gdb(1) can be used on a kernel coredump. 121 122#makeoptions DEBUG="-g" 123 124 125## Adds code to the kernel that does internal consistency checks, and will 126## cause the kernel to panic if corruption of internal data structures 127## is detected. 128#options DIAGNOSTIC # extra kernel sanity checking 129 130## Enable (possibly expensive) debugging code that may also display messages 131## on the system console 132#options DEBUG 133#options LOCKDEBUG 134#options SYSCALL_DEBUG 135 136## Make SCSI error messages more verbose when explaining their meanings. 137options SCSIVERBOSE 138 139options MIIVERBOSE # verbose PHY autoconfig messages 140 141## `INSECURE' turns off the kernel security level (securelevel = 0 always). 142## This allows writing to /dev/mem, loading kernel modules while multi-user, 143## and other insecurities good only for development work. Do not use this 144## option on a production machine. 145#options INSECURE 146 147## `FDSCRIPTS' allows non-readable but executable scripts by providing a 148## pre-opened opaque file to the script interpreter. `SETUIDSCRIPTS', 149## which implies FDSCRIPTS, allows scripts to be set-user-id using the same 150## opaque file mechanism. Perl calls this "secure setuid scripts." 151 152#options FDSCRIPTS 153#options SETUIDSCRIPTS 154 155## Options for compatibility with previous releases foreign system binaries. 156## In the cases of COMPAT_SUNOS and COMPAT_SVR4, you may need to set up 157## additional user-level utilities or system configuration files. See 158## compat_sunos(8) and compat_svr4(8). 159 160options COMPAT_43 # 4.3BSD system interfaces 161options COMPAT_10 # NetBSD 1.0, 162options COMPAT_11 # NetBSD 1.1, 163options COMPAT_12 # NetBSD 1.2, 164options COMPAT_13 # NetBSD 1.3, 165options COMPAT_14 # NetBSD 1.4, 166options COMPAT_15 # NetBSD 1.5, 167options COMPAT_16 # NetBSD 1.6, 168options COMPAT_20 # NetBSD 2.0, 169options COMPAT_30 # NetBSD 3.0, 170options COMPAT_40 # NetBSD 4.0, 171options COMPAT_50 # NetBSD 5.0, 172options COMPAT_60 # NetBSD 6.0, and 173options COMPAT_70 # NetBSD 7.0 binary compatibility 174options COMPAT_SUNOS # SunOS 4.x binary compatibility 175options COMPAT_SVR4 # SunOS 5.x binary compatibility 176options COMPAT_BSDPTY # /dev/[pt]ty?? ptys. 177 178## File systems. You probably need at least one of FFS or NFS. 179file-system FFS # Berkeley Fast Filesystem 180file-system NFS # Sun NFS-compatible filesystem client 181file-system KERNFS # kernel data-structure filesystem 182file-system NULLFS # NULL layered filesystem 183file-system OVERLAY # overlay file system 184file-system MFS # memory-based filesystem 185file-system FDESC # user file descriptor filesystem 186file-system UMAPFS # uid/gid remapping filesystem 187file-system LFS # Log-based filesystem (still experimental) 188file-system PUFFS # Userspace file systems (e.g. ntfs-3g & sshfs) 189file-system PROCFS # /proc 190file-system CD9660 # ISO 9660 + Rock Ridge file system 191file-system UNION # union file system 192file-system MSDOSFS # MS-DOS FAT filesystem(s). 193file-system CODA # Coda File System; also needs vcoda (below) 194file-system PTYFS # /dev/pts/N support 195file-system TMPFS # Efficient memory file-system 196#file-system UDF # experimental - OSTA UDF CD/DVD file-system 197 198## File system options. 199options NFSSERVER # Sun NFS-compatible filesystem server 200options QUOTA # FFS quotas 201#options FFS_EI # FFS Endian Independent support 202options WAPBL # File system journaling support 203#options UFS_DIRHASH # UFS Large Directory Hashing - Experimental 204#options FFS_NO_SNAPSHOT # No FFS snapshot support 205options UFS_EXTATTR # Extended attribute support for UFS1 206 207## Network protocol support. In most environments, INET is required. 208options INET # IP (Internet Protocol) v4 209options INET6 # IPV6 210#options IPSEC # IP security 211#options IPSEC_DEBUG # debug for IP security 212#options GATEWAY # packet forwarding ("router switch") 213#options MROUTING # packet forwarding of multicast packets 214#options PIM # Protocol Independent Multicast 215#options DIRECTED_BROADCAST # allow broadcasts through routers 216#options NETATALK # AppleTalk (over Ethernet) protocol 217options NTP # Network Time Protocol in-kernel support 218#options PPS_SYNC # Add serial line synchronization for NTP 219options IPFILTER_LOG # Add ipmon(8) logging for ipfilter device 220options IPFILTER_LOOKUP # ippool(8) support 221options IPFILTER_COMPAT # Compat for IP-Filter 222#options IPFILTER_DEFAULT_BLOCK # block all packets by default 223options PPP_BSDCOMP # Add BSD compression to ppp device 224options PPP_DEFLATE # Add deflate (libz) compression to ppp device 225options PPP_FILTER # Add active filters for ppp (via bpf) 226 227#options ALTQ # Manipulate network interfaces' output queues 228#options ALTQ_BLUE # Stochastic Fair Blue 229#options ALTQ_CBQ # Class-Based Queueing 230#options ALTQ_CDNR # Diffserv Traffic Conditioner 231#options ALTQ_FIFOQ # First-In First-Out Queue 232#options ALTQ_FLOWVALVE # RED/flow-valve (red-penalty-box) 233#options ALTQ_HFSC # Hierarchical Fair Service Curve 234#options ALTQ_LOCALQ # Local queueing discipline 235#options ALTQ_PRIQ # Priority Queueing 236#options ALTQ_RED # Random Early Detection 237#options ALTQ_RIO # RED with IN/OUT 238#options ALTQ_WFQ # Weighted Fair Queueing 239 240 241 242#### Main bus and CPU .. all systems. 243mainbus0 at root 244cpu0 at mainbus0 245cpuunit0 at mainbus0 # sun4d 246cpuunit* at mainbus0 # sun4d 247cpu0 at cpuunit0 # sun4d 248 249#### SX rendering engine found in SS20 and SS10SX 250sx0 at mainbus0 251 252#### Bus types found on SPARC systems. 253 254sbus0 at mainbus0 # sun4c 255obio0 at mainbus0 # sun4 and sun4m 256sparcvme0 at mainbus0 # sun4 257iommu0 at mainbus0 # sun4m 258sbus0 at iommu0 # sun4m 259sparcvme0 at iommu0 # sun4m 260vme0 at sparcvme0 # MI VME attachment 261bootbus0 at cpuunit0 # sun4d 262bootbus* at cpuunit? # sun4d 263 264## SBus expander box 265xbox* at sbus? slot ? offset ? 266sbus* at xbox? 267 268## SBus to PCMCIA bridge 269nell* at sbus? slot ? offset ? # PCMCIA bridge 270pcmcia* at nell? 271tslot* at sbus? slot ? offset ? # PCMCIA bridge (tadpole 3gx) 272pcmcia* at tslot? 273 274#### Standard system devices -- all required for a given architecture 275 276## Auxiliary system registers on sun4c and sun4m 277auxreg0 at mainbus0 # sun4c 278auxreg0 at obio0 # sun4m 279auxiotwo0 at obio0 # only on Tadpole SPARCbook. 280 281## Power status and control register on Sun4m systems 282power0 at obio0 283 284## Mostek clock found on 4/300, sun4c, sun4m and sun4d systems. 285## The Mostek clock NVRAM is the "eeprom" on sun4/300 systems. 286clock0 at mainbus0 # sun4c 287clock0 at obio0 # sun4m 288clock0 at obio0 addr 0xf2000000 # sun4/300 289clock0 at bootbus0 # sun4d 290 291## Intersil clock found on 4/100 and 4/200 systems. 292oclock0 at obio0 addr 0xf3000000 # sun4/200 293oclock0 at obio0 addr 0x03000000 # sun4/100 294 295## Memory error registers. 296memreg0 at mainbus0 # sun4c 297memreg0 at obio0 # sun4m 298memreg0 at obio0 addr 0xf4000000 # sun4/200 and sun4/300 299memreg0 at obio0 addr 0x04000000 # sun4/100 300 301## ECC memory control 302eccmemctl0 at mainbus0 # sun4m 303 304## Timer chip found on 4/300, sun4c, and sun4m systems. 305timer0 at mainbus0 # sun4c 306timer0 at obio0 # sun4m 307timer0 at obio0 addr 0xef000000 # sun4/300 308 309## EEPROM found on 4/100 and 4/200 systems. Note that the 4/300 310## doesn't use this driver; the `EEPROM' is in the NVRAM on the 311## Mostek clock chip on 4/300 systems. 312eeprom0 at obio0 addr 0xf2000000 # sun4/200 313eeprom0 at obio0 addr 0x02000000 # sun4/100 314 315 316#### Serial port configuration 317 318## Zilog 8530 serial chips. Each has two-channels. 319## zs0 is ttya and ttyb. zs1 is the keyboard and mouse. 320zs0 at mainbus0 # sun4c 321zs0 at obio0 # sun4m 322zs0 at obio0 addr 0xf1000000 level 12 # sun4/200 and sun4/300 323zs0 at obio0 addr 0x01000000 level 12 # sun4/100 324zs0 at bootbus0 # sun4d 325zstty0 at zs0 channel 0 # ttya 326zstty1 at zs0 channel 1 # ttyb 327 328zs1 at mainbus0 # sun4c 329zs1 at obio0 # sun4m 330zs1 at obio0 addr 0xf0000000 level 12 # sun4/200 and sun4/300 331zs1 at obio0 addr 0x00000000 level 12 # sun4/100 332zs1 at bootbus0 # sun4d 333 334# old kbd and mouse attachments 335#kbd0 at zs1 channel 0 # keyboard 336#ms0 at zs1 channel 1 # mouse 337zstty* at zs? 338 339# these are for wscons 340kbd0 at zstty? 341ms0 at zstty? 342wskbd* at wskbddev? 343wsmouse* at wsmousedev? 344 345zs2 at obio0 addr 0xe0000000 level 12 # sun4/300 346zstty2 at zs2 channel 0 # ttyc 347zstty3 at zs2 channel 1 # ttyd 348 349zs* at bootbus? # sun4d 350zstty* at zs? 351 352## NS16x50 serial chips and clones. Present on the 353## Sun JavaStation-1 and Tadpole SPARCbook 3 354com* at obio0 # sun4m 355 356# Parallel port. 357bpp* at sbus? slot? offset ? 358 359## Magma Serial/Parallel driver 360magma* at sbus? slot ? offset ? 361mtty* at magma? 362mbpp* at magma? 363 364## SUNW,spif Serial/Parallel driver 365spif* at sbus? slot ? offset ? 366stty* at spif? 367sbpp* at spif? 368 369## PCMCIA serial interfaces 370#com* at pcmcia? 371#pcmcom* at pcmcia? 372#com* at pcmcom? 373 374#### Disk controllers and disks 375 376# 377 378## The following flags may be set for the NCR53c94 based esp driver: 379## bits 0-7: disable disconnect/reselect for the corresponding target 380## bits 8-15: disable synchronous negotiation for target [bit-8] 381 382## sun4/300, sun4c, sun4m on-board SCSI, and FSBE/S SBus SCSI cards. 383## Both `dma' and `esp' are needed in all cases. 384## Two kinds of additional SBus SCSI interfaces are available. One uses 385## "esp at sbus" like the sun4c on-board; the other uses "esp at dma". 386 387## sun4/300 SCSI - an NCR53c94 or equivalent behind 388## an LSI Logic DMA controller 389 390dma0 at obio0 addr 0xfa001000 level 4 # sun4/300 391esp0 at obio0 addr 0xfa000000 level 4 flags 0x0000 # sun4/300 392 393dma0 at sbus0 slot ? offset ? # sun4c/sun4m 394esp0 at sbus0 slot ? offset ? flags 0x0000 # sun4c 395esp0 at dma0 flags 0x0000 # sun4m 396 397# FSBE/S SCSI & SunSwift Sbus FAS366 398dma* at sbus? slot ? offset ? # SBus 399esp* at sbus? slot ? offset ? flags 0x0000 # SBus 400esp* at dma? flags 0x0000 # SBus 401 402scsibus* at esp? 403 404## Qlogic ISP SBus SCSI Card 405isp* at sbus? slot ? offset ? 406scsibus* at isp? 407 408## NCR5380-based "Sun SCSI 3" VME SCSI controller. 409## This driver has several flags which may be enabled by OR'ing 410## the values and using the "flags" directive. 411## Valid flags are: 412## 413## 0x01 Use DMA (may be polled) 414## 0x02 Use DMA completion interrupts 415## 0x04 Allow disconnect/reselect 416## 417## E.g. the following would enable DMA, interrupts, and reselect: 418## si0 at vme0 addr 0x200000 irq 3 vect 0x40 flags 0x07 419## 420## By default, DMA is enabled in the driver. 421 422si0 at vme0 addr 0x200000 irq 2 vect 0x40 423scsibus* at si? 424 425## NCR5380-based "SCSI Weird" on-board SCSI interface found 426## on sun4/100 systems. The flags are the same as the "si" 427## controller. Note, while DMA is enabled by default, only 428## polled DMA works at this time, and reselects do not work 429## on this particular controller. 430 431sw0 at obio0 addr 0x0a000000 level 3 432scsibus* at sw? 433 434## PCMCIA SCSI controllers 435#aic* at pcmcia? 436#spc* at pcmcia? 437#scsibus* at aic? 438#scsibus* at spc? 439 440 441## These entries find devices on all SCSI busses and assign 442## unit numbers dynamically. 443sd* at scsibus? target ? lun ? # SCSI disks 444st* at scsibus? target ? lun ? # SCSI tapes 445cd* at scsibus? target ? lun ? # SCSI CD-ROMs 446ch* at scsibus? target ? lun ? # SCSI changer devices 447ss* at scsibus? target ? lun ? # SCSI scanners 448ses* at scsibus? target ? lun ? # SCSI SES/SAF-TE 449uk* at scsibus? target ? lun ? # unknown SCSI 450 451 452## Xylogics 753 or 7053 VME SMD disk controllers and disks, found 453## on sun4 systems. 454xdc0 at vme0 addr 0xee80 irq 3 vect 0x44 455xdc1 at vme0 addr 0xee90 irq 3 vect 0x45 456xdc2 at vme0 addr 0xeea0 irq 3 vect 0x46 457xdc3 at vme0 addr 0xeeb0 irq 3 vect 0x47 458xd* at xdc? drive ? 459 460## Xylogics 451 or 451 VME SMD disk controllers and disks, found 461## on sun4 systems. 462xyc0 at vme0 addr 0xee40 irq 3 vect 0x48 463xyc1 at vme0 addr 0xee48 irq 3 vect 0x49 464xy* at xyc? drive ? 465 466 467## Floppy controller and drive found on SPARCstations. 468 469fdc0 at mainbus0 # sun4c controller 470fdc0 at obio0 # sun4m controller 471fd* at fdc0 # the drive itself 472 473## PCMCIA IDE controllers 474#wdc* at pcmcia? 475#atabus* at ata? 476#wd* at atabus? drive ? flags 0x0000 477 478## A disk-like interface to files. Can be used to create floppy, CD, 479## miniroot images, etc. 480 481pseudo-device vnd 482#options VND_COMPRESSION # compressed vnd(4) 483 484## Concatenated and striped disks; with this, you can create a software-based 485## disk array similar to a "RAID 0" setup. See ccd(4). 486 487pseudo-device ccd 488 489## Cryptographic disk devices; See cgd(4) 490 491#pseudo-device cgd 492 493## RAIDframe disk driver: software RAID driver. See raid(4). 494 495pseudo-device raid 496options RAID_AUTOCONFIG # auto-configuration of RAID components 497# Options to enable various other RAIDframe RAID types. 498# options RF_INCLUDE_EVENODD=1 499# options RF_INCLUDE_RAID5_RS=1 500# options RF_INCLUDE_PARITYLOGGING=1 501# options RF_INCLUDE_CHAINDECLUSTER=1 502# options RF_INCLUDE_INTERDECLUSTER=1 503# options RF_INCLUDE_PARITY_DECLUSTERING=1 504# options RF_INCLUDE_PARITY_DECLUSTERING_DS=1 505 506 507## Memory disk device, used on boot floppies with compressed 508## kernel-plus-root-disk images. 509 510#pseudo-device md 511 512 513#### Network interfaces 514 515## LANCE Ethernet - an AMD 7990 LANCE behind specialized DMA glue 516## Three flavors of additional SBus ethernets are available. One attaches 517## directly like the sun4c on-board, one uses the ledma device like the 518## sun4m on-board, and one uses the lebuffer device. 519 520le0 at obio0 addr 0xf9000000 level 6 # sun4/300 521le0 at sbus0 slot ? offset ? # sun4c on-board 522ledma0 at sbus0 slot ? offset ? # sun4m on-board 523le0 at ledma0 # sun4m on-board 524le* at sbus? slot ? offset ? # SBus 525ledma* at sbus? slot ? offset ? # SBus 526le* at ledma? # SBus 527lebuffer0 at sbus? slot ? offset ? # SBus 528le0 at lebuffer? # SBus 529lebuffer* at sbus? slot ? offset ? # SBus 530le* at lebuffer? # SBus 531 532 533## sun4/100 and sun4/200 Ethernet - an Intel 82586 on-board 534## or on a Multibus/VME card. 535ie0 at obio0 addr 0xf6000000 level 6 # sun4/200 on-board 536ie0 at obio0 addr 0x06000000 level 6 # sun4/100 on-board 537## VME: the first [addr,len] pair specifies the device registers; 538## the second pair specifies the on-board memory buffer 539ie1 at vme0 addr 0xe88000,0xe00000 len -1,0x40000 irq 3 vect 0x75 540ie2 at vme0 addr 0x31ff02,0x300000 len -1,0x40000 irq 3 vect 0x76 541ie3 at vme0 addr 0x35ff02,0x300000 len -1,0x40000 irq 3 vect 0x77 542ie4 at vme0 addr 0x2dff02,0x200000 len -1,0x40000 irq 3 vect 0x7c 543 544## Quad Ethernet Controller with BigMac (be, 10/100MBd) and Mace Ethernet 545## (qe, 10MBd) attached. 546qec* at sbus? slot ? offset ? # Quad Ethernet Controller 547be* at qec? # BigMac Ethernet (10/100MBd) 548qe* at qec? # Mace Ethernet (10MBd) 549 550## Happy Meal Ethernet 551hme* at sbus? slot ? offset ? 552 553# midway ATM 554en0 at sbus? slot ? offset ? 555 556# PCMCIA ethernet devices 557#ep* at pcmcia? 558#mbe* at pcmcia? 559#ne* at pcmcia? 560#sm* at pcmcia? 561 562## PCMCIA wavelan card 563#wi* at pcmcia? function ? # Lucent WaveLan IEEE (802.11) 564 565# MII/PHY support 566exphy* at mii? phy ? # 3Com internal PHYs 567icsphy* at mii? phy ? # Integrated Circuit Systems ICS189x 568inphy* at mii? phy ? # Intel 82555 PHYs 569lxtphy* at mii? phy ? # Level One LXT-970 PHYs 570nsphy* at mii? phy ? # NS83840 PHYs 571qsphy* at mii? phy ? # Quality Semiconductor QS6612 PHYs 572sqphy* at mii? phy ? # Seeq 80220/80221/80223 PHYs 573tlphy* at mii? phy ? # ThunderLAN PHYs 574ukphy* at mii? phy ? # generic unknown PHYs 575 576## Loopback network interface; required 577pseudo-device loop 578 579## SLIP and CSLIP interfaces, for IP over a serial line. 580pseudo-device sl 581 582## PPP, the successor to SLIP. See pppd(8). 583pseudo-device ppp 584 585## PPP over Ethernet (RFC 2516) 586pseudo-device pppoe 587 588## Starmode Radio IP, a special hardware network device. 589#pseudo-device strip 590 591## Network "tunnel" device, allowing protocol stacks to run in the userland. 592## This is used by the third-party user-mode "ppp" program, and others. 593pseudo-device tun 594pseudo-device tap # virtual Ethernet 595 596## Generic L3 over IP tunnel 597#pseudo-device gre # generic L3 over IP tunnel 598 599## Berkeley Packet Filter, required to run RARPD. A generic C-language 600## interface that allows selective examining of incoming packets. 601pseudo-device bpfilter 602 603#pseudo-device carp # Common Address Redundancy Protocol 604 605## IP Filter, used in firewall and NAT applications. See ipnat(8) for 606## one example of the use of the IP Filter. 607pseudo-device ipfilter 608 609## for IPv6 610pseudo-device gif # IPv[46] over IPv[46] tunnel (RFC1933) 611#pseudo-device faith # IPv[46] tcp relay translation i/f 612pseudo-device stf # 6to4 IPv6 over IPv4 encapsulation 613 614## IEEE 802.1Q Virtual LAN encapsulation, see vlan(4). 615pseudo-device vlan 616 617## Simple inter-network traffic bridging 618pseudo-device bridge 619#options BRIDGE_IPF # bridge uses IP/IPv6 pfil hooks too 620pseudo-device agr # IEEE 802.3ad link aggregation 621 622## accept filters 623pseudo-device accf_data # "dataready" accept filter 624pseudo-device accf_http # "httpready" accept filter 625 626#### Audio and video devices 627 628## /dev/audio support (`audioamd' plus `audio') 629## 630audioamd0 at mainbus0 # sun4c 631audioamd0 at obio0 # sun4m 632audioamd0 at sbus0 slot ? offset ? # sun4m 633 634audiocs0 at sbus0 slot ? offset ? # SUNW,CS4231 635 636#options DBRI_DEBUG # noisy debug output from the dbri driver 637#options DBRI_BIG_BUFFER # use bigger DMA buffers, for slow CPUs 638dbri* at sbus? slot ? offset ? # SUNW,DBRI[s3|e] 639 640audio* at audiobus? 641 642## Sun "bwtwo" black and white framebuffer, found on sun4, sun4c, and sun4m 643## systems. If your sun4 system has a cgfour installed in the P4 slot, 644## the P4 entries for "bwtwo" will attach to the overlay plane of the 645## "cgfour". 646 647bwtwo0 at sbus0 slot ? offset ? # sun4c and sun4m 648bwtwo* at sbus? slot ? offset ? # 649bwtwo0 at obio0 addr 0xfd000000 level 4 # sun4/200 650bwtwo0 at obio0 addr 0xfb300000 level 4 # sun4/300 in P4 slot 651bwtwo0 at obio0 addr 0x0b300000 level 4 # sun4/100 in P4 slot 652 653## Sun "cgtwo" VME color framebuffer 654# XXX no wsdisplay support 655#cgtwo0 at vme0 addr 0x400000 irq ? vect 0xa8 656 657## Sun "cgthree" Sbus color framebuffer 658cgthree0 at sbus? slot ? offset ? 659cgthree* at sbus? slot ? offset ? 660 661## Sun "cgfour" color framebuffer with overlay plane. See above comment 662## regarding overlay plane. 663# XXX no wsdisplay support 664#cgfour0 at obio0 addr 0xfb300000 level 4 # sun4/300 P4 665#cgfour0 at obio0 addr 0x0b300000 level 4 # sun4/100 P4 666 667## Sun "cgsix" accelerated color framebuffer. 668cgsix0 at sbus? slot ? offset ? 669cgsix* at sbus? slot ? offset ? 670cgsix0 at obio0 addr 0xfb000000 level 4 # sun4/300 P4 671cgsix0 at obio0 addr 0x0b000000 level 4 # sun4/100 P4 672 673## Sun "cgeight" 24-bit framebuffer 674# XXX no wsdisplay support 675#cgeight0 at obio0 addr 0xfb300000 level 4 # sun4/300 P4 676#cgeight0 at obio0 addr 0x0b300000 level 4 # sun4/100 P4 677 678## Sun "tcx" accelerated color framebuffer. 679# there can be only one 680tcx0 at sbus? slot ? offset ? 681 682## Sun CG12 / Matrox SG3 accelerated 24bit framebuffer 683cgtwelve* at sbus? slot ? offset ? 684# the driver can use the color framebuffer or the monochrome overlay 685# the latter is faster 686options CG12_COLOR 687 688# Sun "cgfourteen" accelerated 24-bit framebuffer. 689cgfourteen* at obio0 # sun4m 690 691# P9100-based display on Tadpole SPARCbook 3. 692pnozz0 at sbus? slot ? offset ? 693# the SPARCbook 3 hardware docs say that accesses to P9100 registers need to be 694# 'latched in' but at least my 3GX works happily without 695# Enable it by default since we don't know which hardware really needs it. 696options PNOZZ_USE_LATCH 697 698# Sun ZX/Leo 24-bit framebuffer 699zx* at sbus? slot ? offset ? 700 701# Fujitsu AG-10e accelerated graphics 8/24-bit board 702agten* at sbus? slot ? offset ? 703 704## Southland Media Systems (now Quantum 3D) MGX 705mgx* at sbus? slot ? offset ? 706 707# generic framebuffer console 708genfb* at sbus? slot ? offset ? 709 710# make sure wsdisplay0 is the console 711wsdisplay0 at wsemuldisplaydev? console 1 712wsdisplay* at wsemuldisplaydev? 713 714#### Other device configuration 715 716# Tadpole microcontroller 717tctrl0 at obio0 718 719# Aurora Personality Chip (APC) on SPARCstation-4/5 720# Not enabled by default as it may hang some systems 721#apc* at sbus? slot ? offset ? 722 723## Pseudo ttys, required for network logins and programs like screen. 724 725pseudo-device pty # pseudo-terminals 726 727## Random device, used to implement /dev/random (a source of random noise), 728## and generate randomness for some kernel formulae. 729 730 731# a pseudo device needed for Coda # also needs CODA (above) 732pseudo-device vcoda # coda minicache <-> venus comm. 733 734pseudo-device clockctl # user control of clock subsystem 735pseudo-device ksyms # /dev/ksyms 736#pseudo-device pf # PF packet filter 737#pseudo-device pflog # PF log if 738pseudo-device fss # file system snapshot device 739pseudo-device wsmux # mouse and keyboard multiplexor 740pseudo-device wsfont 741pseudo-device putter # for puffs and pud 742 743#options FILEASSOC # fileassoc(9) 744 # and PAX_SEGVGUARD 745 746# Veriexec 747# 748# a pseudo device needed for veriexec 749#pseudo-device veriexec 750# 751# Uncomment the fingerprint methods below that are desired. Note that 752# removing fingerprint methods will have almost no impact on the kernel 753# code size. 754# 755#options VERIFIED_EXEC_FP_RMD160 756#options VERIFIED_EXEC_FP_SHA256 757#options VERIFIED_EXEC_FP_SHA384 758#options VERIFIED_EXEC_FP_SHA512 759#options VERIFIED_EXEC_FP_SHA1 760#options VERIFIED_EXEC_FP_MD5 761 762#options PAX_MPROTECT=0 # PaX mprotect(2) restrictions 763 # (for static binaries only for now) 764