GENERIC revision 1.265
1 # $NetBSD: GENERIC,v 1.265 2019/04/13 08:23:00 isaki Exp $ 2 # 3 # GENERIC machine description file 4 # 5 # This machine description file is used to generate the default NetBSD 6 # kernel. The generic kernel does not include all options, subsystems 7 # and device drivers, but should be useful for most applications. 8 # 9 # The machine description file can be customised for your specific 10 # machine to reduce the kernel size and improve its performance. 11 # 12 # For further information on compiling NetBSD kernels, see the config(8) 13 # man page. 14 # 15 # For further information on hardware support for this architecture, see 16 # the intro(4) man page. For further information about kernel options 17 # for this architecture, see the options(4) man page. For an explanation 18 # of each device driver in this file see the section 4 man page for the 19 # device. 20 21 include "arch/sparc/conf/std.sparc" 22 23 options INCLUDE_CONFIG_FILE # embed config file in kernel binary 24 25 #ident "GENERIC-$Revision: 1.265 $" 26 27 maxusers 32 28 29 ## System kernel configuration. See options(4) for more detail. 30 31 32 # Options for variants of the Sun SPARC architecure. 33 # We currently support three architecture types; at least one is required. 34 options SUN4 # sun4/100, sun4/200, sun4/300 35 options SUN4C # sun4c - SS1, 1+, 2, ELC, SLC, IPC, IPX, etc. 36 options SUN4M # sun4m - SS10, SS20, Classic, etc. 37 options SUN4D # sun4d - SS1000, SC2000 38 39 options SUN4_MMU3L # sun4/400 3-level MMU 40 41 ## System options specific to the sparc machine type 42 43 # Blink the power LED on some machines to indicate the system load. 44 #options BLINK 45 46 # wscons stuff 47 #options WSEMUL_SUN 48 options WSEMUL_VT100 49 options WSDISPLAY_COMPAT_RAWKBD 50 options WSDISPLAY_CUSTOM_OUTPUT 51 options WS_DEFAULT_FG=WSCOL_BLACK 52 options WS_DEFAULT_BG=WSCOL_LIGHT_WHITE 53 options WS_KERNEL_FG=WSCOL_GREEN 54 options WS_KERNEL_BG=WSCOL_LIGHT_WHITE 55 options WSDISPLAY_COMPAT_PCVT 56 options WSDISPLAY_COMPAT_SYSCONS 57 options WSDISPLAY_COMPAT_USL # wsconscfg VT handling 58 59 options WSDISPLAY_SCROLLSUPPORT 60 61 options FONT_GALLANT12x22 # the console font 62 options FONT_BOLD8x16 # a somewhat smaller font 63 64 #### System options that are the same for all ports 65 66 ## Root device configuration: change the ?'s if you are going to use a 67 ## nonstandard root partition (other than where the kernel is booted from) 68 ## and/or nonstandard root type (not ffs or nfs). Normally this can be 69 ## automagically determined at boot time. 70 71 config netbsd root on ? type ? 72 73 ## System call tracing (see ktrace(1)). 74 options KTRACE 75 76 ## System V compatible IPC subsystem. (msgctl(2), semctl(2), and shmctl(2)) 77 options SYSVMSG # System V message queues 78 options SYSVSEM # System V semaphores 79 options SYSVSHM # System V shared memory 80 81 options MODULAR # new style module(7) framework 82 options MODULAR_DEFAULT_AUTOLOAD 83 84 options USERCONF # userconf(4) support 85 #options PIPE_SOCKETPAIR # smaller, but slower pipe(2) 86 options SYSCTL_INCLUDE_DESCR # Include sysctl descriptions in kernel 87 88 # Alternate buffer queue strategies for better responsiveness under high 89 # disk I/O load. 90 #options BUFQ_READPRIO 91 #options BUFQ_PRIOCSCAN 92 93 ## NFS boot options; tries DHCP/BOOTP then BOOTPARAM 94 options NFS_BOOT_BOOTPARAM 95 #options NFS_BOOT_BOOTP 96 options NFS_BOOT_DHCP 97 98 #### Debugging options 99 100 ## The DDB in-kernel debugger runs at panic (unless DDB_ONPANIC=0), or at 101 ## serial console break or keyboard reset, where the PROM would normally 102 ## intercept. DDB_HISTORY_SIZE adds up/down arrow command history. 103 options DDB # kernel dynamic debugger 104 options DDB_HISTORY_SIZE=100 # enable history editing in DDB 105 #options DDB_ONPANIC=1 # see also sysctl(7): `ddb.onpanic' 106 107 ## You may also use gdb, on another computer connected to this machine over 108 ## a serial port. Both KGDB_DEV and KGDB_DEVRATE should be specified; 109 ## KGDB_DEV is a dev_t encoded device number of the serial port to use, where 110 ## the minor device number encodes the PROM enumeration of the serial ports, 111 ## i.e.: 112 ## 0xc00 = ttya, 0xc01 = ttyb, 0xc02 = ttyc, 0xc03 = ttyd. 113 ## (Note: ttyc and ttyd are available only on some sun4 models) 114 #options KGDB # support for kernel gdb 115 #options KGDB_DEV=0xc01 # kgdb device number (this is `ttyb') 116 #options KGDB_DEVRATE=38400 # baud rate 117 118 119 ## Compile the kernel with debugging symbols (`netbsd.gdb' is the debug file), 120 ## such that gdb(1) can be used on a kernel coredump. 121 122 #makeoptions DEBUG="-g" 123 124 125 ## Adds code to the kernel that does internal consistency checks, and will 126 ## cause the kernel to panic if corruption of internal data structures 127 ## is detected. 128 options DIAGNOSTIC # extra kernel sanity checking 129 130 ## Enable (possibly expensive) debugging code that may also display messages 131 ## on the system console 132 #options DEBUG 133 #options LOCKDEBUG 134 #options SYSCALL_DEBUG 135 136 ## Make SCSI error messages more verbose when explaining their meanings. 137 options SCSIVERBOSE 138 139 options MIIVERBOSE # verbose PHY autoconfig messages 140 141 ## `INSECURE' turns off the kernel security level (securelevel = 0 always). 142 ## This allows writing to /dev/mem, loading kernel modules while multi-user, 143 ## and other insecurities good only for development work. Do not use this 144 ## option on a production machine. 145 #options INSECURE 146 147 ## `FDSCRIPTS' allows non-readable but executable scripts by providing a 148 ## pre-opened opaque file to the script interpreter. `SETUIDSCRIPTS', 149 ## which implies FDSCRIPTS, allows scripts to be set-user-id using the same 150 ## opaque file mechanism. Perl calls this "secure setuid scripts." 151 152 #options FDSCRIPTS 153 #options SETUIDSCRIPTS 154 155 ## Options for compatibility with previous releases foreign system binaries. 156 ## In the cases of COMPAT_SUNOS, you may need to set up additional user-level 157 ## utilities or system configuration files. See compat_sunos(8). 158 159 include "conf/compat_netbsd10.config" 160 options COMPAT_SUNOS # SunOS 4.x binary compatibility 161 162 ## File systems. You probably need at least one of FFS or NFS. 163 file-system FFS # Berkeley Fast Filesystem 164 file-system NFS # Sun NFS-compatible filesystem client 165 file-system KERNFS # kernel data-structure filesystem 166 file-system NULLFS # NULL layered filesystem 167 file-system OVERLAY # overlay file system 168 file-system MFS # memory-based filesystem 169 file-system FDESC # user file descriptor filesystem 170 file-system UMAPFS # uid/gid remapping filesystem 171 file-system LFS # Log-based filesystem (still experimental) 172 file-system PUFFS # Userspace file systems (e.g. ntfs-3g & sshfs) 173 file-system PROCFS # /proc 174 file-system CD9660 # ISO 9660 + Rock Ridge file system 175 file-system UNION # union file system 176 file-system MSDOSFS # MS-DOS FAT filesystem(s). 177 file-system CODA # Coda File System; also needs vcoda (below) 178 file-system PTYFS # /dev/pts/N support 179 file-system TMPFS # Efficient memory file-system 180 #file-system UDF # experimental - OSTA UDF CD/DVD file-system 181 182 ## File system options. 183 options NFSSERVER # Sun NFS-compatible filesystem server 184 options QUOTA # FFS quotas 185 #options QUOTA2 # new, in-filesystem UFS quotas 186 #options FFS_EI # FFS Endian Independent support 187 options WAPBL # File system journaling support 188 #options UFS_DIRHASH # UFS Large Directory Hashing - Experimental 189 #options FFS_NO_SNAPSHOT # No FFS snapshot support 190 options UFS_EXTATTR # Extended attribute support for UFS1 191 192 ## Network protocol support. In most environments, INET is required. 193 options INET # IP (Internet Protocol) v4 194 options INET6 # IPV6 195 #options IPSEC # IP security 196 #options IPSEC_DEBUG # debug for IP security 197 #options GATEWAY # packet forwarding ("router switch") 198 #options MROUTING # packet forwarding of multicast packets 199 #options PIM # Protocol Independent Multicast 200 #options NETATALK # AppleTalk (over Ethernet) protocol 201 options NTP # Network Time Protocol in-kernel support 202 #options PPS_SYNC # Add serial line synchronization for NTP 203 options PPP_BSDCOMP # Add BSD compression to ppp device 204 options PPP_DEFLATE # Add deflate (libz) compression to ppp device 205 options PPP_FILTER # Add active filters for ppp (via bpf) 206 207 #options ALTQ # Manipulate network interfaces' output queues 208 #options ALTQ_BLUE # Stochastic Fair Blue 209 #options ALTQ_CBQ # Class-Based Queueing 210 #options ALTQ_CDNR # Diffserv Traffic Conditioner 211 #options ALTQ_FIFOQ # First-In First-Out Queue 212 #options ALTQ_FLOWVALVE # RED/flow-valve (red-penalty-box) 213 #options ALTQ_HFSC # Hierarchical Fair Service Curve 214 #options ALTQ_LOCALQ # Local queueing discipline 215 #options ALTQ_PRIQ # Priority Queueing 216 #options ALTQ_RED # Random Early Detection 217 #options ALTQ_RIO # RED with IN/OUT 218 #options ALTQ_WFQ # Weighted Fair Queueing 219 220 221 222 #### Main bus and CPU .. all systems. 223 mainbus0 at root 224 cpu0 at mainbus0 225 cpuunit0 at mainbus0 # sun4d 226 cpuunit* at mainbus0 # sun4d 227 cpu0 at cpuunit0 # sun4d 228 229 #### SX rendering engine found in SS20 and SS10SX 230 sx0 at mainbus0 231 232 #### Bus types found on SPARC systems. 233 234 sbus0 at mainbus0 # sun4c 235 obio0 at mainbus0 # sun4 and sun4m 236 sparcvme0 at mainbus0 # sun4 237 iommu0 at mainbus0 # sun4m 238 sbus0 at iommu0 # sun4m 239 sparcvme0 at iommu0 # sun4m 240 vme0 at sparcvme0 # MI VME attachment 241 bootbus0 at cpuunit0 # sun4d 242 bootbus* at cpuunit? # sun4d 243 244 ## SBus expander box 245 xbox* at sbus? slot ? offset ? 246 sbus* at xbox? 247 248 ## SBus to PCMCIA bridge 249 nell* at sbus? slot ? offset ? # PCMCIA bridge 250 pcmcia* at nell? 251 tslot* at sbus? slot ? offset ? # PCMCIA bridge (tadpole 3gx) 252 pcmcia* at tslot? 253 254 #### Standard system devices -- all required for a given architecture 255 256 ## Auxiliary system registers on sun4c and sun4m 257 auxreg0 at mainbus0 # sun4c 258 auxreg0 at obio0 # sun4m 259 auxiotwo0 at obio0 # only on Tadpole SPARCbook. 260 261 ## Power status and control register on Sun4m systems 262 power0 at obio0 263 264 ## Mostek clock found on 4/300, sun4c, sun4m and sun4d systems. 265 ## The Mostek clock NVRAM is the "eeprom" on sun4/300 systems. 266 clock0 at mainbus0 # sun4c 267 clock0 at obio0 # sun4m 268 clock0 at obio0 addr 0xf2000000 # sun4/300 269 clock0 at bootbus0 # sun4d 270 271 ## Intersil clock found on 4/100 and 4/200 systems. 272 oclock0 at obio0 addr 0xf3000000 # sun4/200 273 oclock0 at obio0 addr 0x03000000 # sun4/100 274 275 ## Memory error registers. 276 memreg0 at mainbus0 # sun4c 277 memreg0 at obio0 # sun4m 278 memreg0 at obio0 addr 0xf4000000 # sun4/200 and sun4/300 279 memreg0 at obio0 addr 0x04000000 # sun4/100 280 281 ## ECC memory control 282 eccmemctl0 at mainbus0 # sun4m 283 284 ## Timer chip found on 4/300, sun4c, and sun4m systems. 285 timer0 at mainbus0 # sun4c 286 timer0 at obio0 # sun4m 287 timer0 at obio0 addr 0xef000000 # sun4/300 288 289 ## EEPROM found on 4/100 and 4/200 systems. Note that the 4/300 290 ## doesn't use this driver; the `EEPROM' is in the NVRAM on the 291 ## Mostek clock chip on 4/300 systems. 292 eeprom0 at obio0 addr 0xf2000000 # sun4/200 293 eeprom0 at obio0 addr 0x02000000 # sun4/100 294 295 296 #### Serial port configuration 297 298 ## Zilog 8530 serial chips. Each has two-channels. 299 ## zs0 is ttya and ttyb. zs1 is the keyboard and mouse. 300 zs0 at mainbus0 # sun4c 301 zs0 at obio0 # sun4m 302 zs0 at obio0 addr 0xf1000000 level 12 # sun4/200 and sun4/300 303 zs0 at obio0 addr 0x01000000 level 12 # sun4/100 304 zs0 at bootbus0 # sun4d 305 zstty0 at zs0 channel 0 # ttya 306 zstty1 at zs0 channel 1 # ttyb 307 308 zs1 at mainbus0 # sun4c 309 zs1 at obio0 # sun4m 310 zs1 at obio0 addr 0xf0000000 level 12 # sun4/200 and sun4/300 311 zs1 at obio0 addr 0x00000000 level 12 # sun4/100 312 zs1 at bootbus0 # sun4d 313 314 # old kbd and mouse attachments 315 #kbd0 at zs1 channel 0 # keyboard 316 #ms0 at zs1 channel 1 # mouse 317 zstty* at zs? 318 319 # these are for wscons 320 kbd0 at zstty? 321 ms0 at zstty? 322 wskbd* at wskbddev? 323 wsmouse* at wsmousedev? 324 325 zs2 at obio0 addr 0xe0000000 level 12 # sun4/300 326 zstty2 at zs2 channel 0 # ttyc 327 zstty3 at zs2 channel 1 # ttyd 328 329 zs* at bootbus? # sun4d 330 zstty* at zs? 331 332 ## NS16x50 serial chips and clones. Present on the 333 ## Sun JavaStation-1 and Tadpole SPARCbook 3 334 com* at obio0 # sun4m 335 336 # Parallel port. 337 bpp* at sbus? slot? offset ? 338 339 ## Magma Serial/Parallel driver 340 magma* at sbus? slot ? offset ? 341 mtty* at magma? 342 mbpp* at magma? 343 344 ## SUNW,spif Serial/Parallel driver 345 spif* at sbus? slot ? offset ? 346 stty* at spif? 347 sbpp* at spif? 348 349 ## PCMCIA serial interfaces 350 #com* at pcmcia? 351 #pcmcom* at pcmcia? 352 #com* at pcmcom? 353 354 #### Disk controllers and disks 355 356 # 357 358 ## The following flags may be set for the NCR53c94 based esp driver: 359 ## bits 0-7: disable disconnect/reselect for the corresponding target 360 ## bits 8-15: disable synchronous negotiation for target [bit-8] 361 362 ## sun4/300, sun4c, sun4m on-board SCSI, and FSBE/S SBus SCSI cards. 363 ## Both `dma' and `esp' are needed in all cases. 364 ## Two kinds of additional SBus SCSI interfaces are available. One uses 365 ## "esp at sbus" like the sun4c on-board; the other uses "esp at dma". 366 367 ## sun4/300 SCSI - an NCR53c94 or equivalent behind 368 ## an LSI Logic DMA controller 369 370 dma0 at obio0 addr 0xfa001000 level 4 # sun4/300 371 esp0 at obio0 addr 0xfa000000 level 4 flags 0x0000 # sun4/300 372 373 dma0 at sbus0 slot ? offset ? # sun4c/sun4m 374 esp0 at sbus0 slot ? offset ? flags 0x0000 # sun4c 375 esp0 at dma0 flags 0x0000 # sun4m 376 377 # FSBE/S SCSI & SunSwift Sbus FAS366 378 dma* at sbus? slot ? offset ? # SBus 379 esp* at sbus? slot ? offset ? flags 0x0000 # SBus 380 esp* at dma? flags 0x0000 # SBus 381 382 scsibus* at esp? 383 384 ## Qlogic ISP SBus SCSI Card 385 isp* at sbus? slot ? offset ? 386 scsibus* at isp? 387 388 ## NCR5380-based "Sun SCSI 3" VME SCSI controller. 389 ## This driver has several flags which may be enabled by OR'ing 390 ## the values and using the "flags" directive. 391 ## Valid flags are: 392 ## 393 ## 0x01 Use DMA (may be polled) 394 ## 0x02 Use DMA completion interrupts 395 ## 0x04 Allow disconnect/reselect 396 ## 397 ## E.g. the following would enable DMA, interrupts, and reselect: 398 ## si0 at vme0 addr 0x200000 irq 3 vect 0x40 flags 0x07 399 ## 400 ## By default, DMA is enabled in the driver. 401 402 si0 at vme0 addr 0x200000 irq 2 vect 0x40 403 scsibus* at si? 404 405 ## NCR5380-based "SCSI Weird" on-board SCSI interface found 406 ## on sun4/100 systems. The flags are the same as the "si" 407 ## controller. Note, while DMA is enabled by default, only 408 ## polled DMA works at this time, and reselects do not work 409 ## on this particular controller. 410 411 sw0 at obio0 addr 0x0a000000 level 3 412 scsibus* at sw? 413 414 ## PCMCIA SCSI controllers 415 #aic* at pcmcia? 416 #spc* at pcmcia? 417 #scsibus* at aic? 418 #scsibus* at spc? 419 420 421 ## These entries find devices on all SCSI busses and assign 422 ## unit numbers dynamically. 423 sd* at scsibus? target ? lun ? # SCSI disks 424 st* at scsibus? target ? lun ? # SCSI tapes 425 cd* at scsibus? target ? lun ? # SCSI CD-ROMs 426 ch* at scsibus? target ? lun ? # SCSI changer devices 427 ss* at scsibus? target ? lun ? # SCSI scanners 428 ses* at scsibus? target ? lun ? # SCSI SES/SAF-TE 429 uk* at scsibus? target ? lun ? # unknown SCSI 430 431 432 ## Xylogics 753 or 7053 VME SMD disk controllers and disks, found 433 ## on sun4 systems. 434 xdc0 at vme0 addr 0xee80 irq 3 vect 0x44 435 xdc1 at vme0 addr 0xee90 irq 3 vect 0x45 436 xdc2 at vme0 addr 0xeea0 irq 3 vect 0x46 437 xdc3 at vme0 addr 0xeeb0 irq 3 vect 0x47 438 xd* at xdc? drive ? 439 440 ## Xylogics 451 or 451 VME SMD disk controllers and disks, found 441 ## on sun4 systems. 442 xyc0 at vme0 addr 0xee40 irq 3 vect 0x48 443 xyc1 at vme0 addr 0xee48 irq 3 vect 0x49 444 xy* at xyc? drive ? 445 446 447 ## Floppy controller and drive found on SPARCstations. 448 449 fdc0 at mainbus0 # sun4c controller 450 fdc0 at obio0 # sun4m controller 451 fd* at fdc0 # the drive itself 452 453 ## PCMCIA IDE controllers 454 #wdc* at pcmcia? 455 #atabus* at ata? 456 #wd* at atabus? drive ? flags 0x0000 457 458 ## A disk-like interface to files. Can be used to create floppy, CD, 459 ## miniroot images, etc. 460 461 pseudo-device vnd 462 #options VND_COMPRESSION # compressed vnd(4) 463 464 ## Concatenated and striped disks; with this, you can create a software-based 465 ## disk array similar to a "RAID 0" setup. See ccd(4). 466 467 pseudo-device ccd 468 469 ## Cryptographic disk devices; See cgd(4) 470 471 #pseudo-device cgd 472 473 ## RAIDframe disk driver: software RAID driver. See raid(4). 474 475 pseudo-device raid 476 options RAID_AUTOCONFIG # auto-configuration of RAID components 477 # Options to enable various other RAIDframe RAID types. 478 # options RF_INCLUDE_EVENODD=1 479 # options RF_INCLUDE_RAID5_RS=1 480 # options RF_INCLUDE_PARITYLOGGING=1 481 # options RF_INCLUDE_CHAINDECLUSTER=1 482 # options RF_INCLUDE_INTERDECLUSTER=1 483 # options RF_INCLUDE_PARITY_DECLUSTERING=1 484 # options RF_INCLUDE_PARITY_DECLUSTERING_DS=1 485 486 487 ## Memory disk device, used on boot floppies with compressed 488 ## kernel-plus-root-disk images. 489 490 #pseudo-device md 491 492 493 #### Network interfaces 494 495 ## LANCE Ethernet - an AMD 7990 LANCE behind specialized DMA glue 496 ## Three flavors of additional SBus ethernets are available. One attaches 497 ## directly like the sun4c on-board, one uses the ledma device like the 498 ## sun4m on-board, and one uses the lebuffer device. 499 500 le0 at obio0 addr 0xf9000000 level 6 # sun4/300 501 le0 at sbus0 slot ? offset ? # sun4c on-board 502 ledma0 at sbus0 slot ? offset ? # sun4m on-board 503 le0 at ledma0 # sun4m on-board 504 le* at sbus? slot ? offset ? # SBus 505 ledma* at sbus? slot ? offset ? # SBus 506 le* at ledma? # SBus 507 lebuffer0 at sbus? slot ? offset ? # SBus 508 le0 at lebuffer? # SBus 509 lebuffer* at sbus? slot ? offset ? # SBus 510 le* at lebuffer? # SBus 511 512 513 ## sun4/100 and sun4/200 Ethernet - an Intel 82586 on-board 514 ## or on a Multibus/VME card. 515 ie0 at obio0 addr 0xf6000000 level 6 # sun4/200 on-board 516 ie0 at obio0 addr 0x06000000 level 6 # sun4/100 on-board 517 ## VME: the first [addr,len] pair specifies the device registers; 518 ## the second pair specifies the on-board memory buffer 519 ie1 at vme0 addr 0xe88000,0xe00000 len -1,0x40000 irq 3 vect 0x75 520 ie2 at vme0 addr 0x31ff02,0x300000 len -1,0x40000 irq 3 vect 0x76 521 ie3 at vme0 addr 0x35ff02,0x300000 len -1,0x40000 irq 3 vect 0x77 522 ie4 at vme0 addr 0x2dff02,0x200000 len -1,0x40000 irq 3 vect 0x7c 523 524 ## Quad Ethernet Controller with BigMac (be, 10/100MBd) and Mace Ethernet 525 ## (qe, 10MBd) attached. 526 qec* at sbus? slot ? offset ? # Quad Ethernet Controller 527 be* at qec? # BigMac Ethernet (10/100MBd) 528 qe* at qec? # Mace Ethernet (10MBd) 529 530 ## Happy Meal Ethernet 531 hme* at sbus? slot ? offset ? 532 533 # PCMCIA ethernet devices 534 #ep* at pcmcia? 535 #mbe* at pcmcia? 536 #ne* at pcmcia? 537 #sm* at pcmcia? 538 539 ## PCMCIA wavelan card 540 #wi* at pcmcia? function ? # Lucent WaveLan IEEE (802.11) 541 542 # MII/PHY support 543 exphy* at mii? phy ? # 3Com internal PHYs 544 icsphy* at mii? phy ? # Integrated Circuit Systems ICS189x 545 inphy* at mii? phy ? # Intel 82555 PHYs 546 lxtphy* at mii? phy ? # Level One LXT-970 PHYs 547 nsphy* at mii? phy ? # NS83840 PHYs 548 qsphy* at mii? phy ? # Quality Semiconductor QS6612 PHYs 549 sqphy* at mii? phy ? # Seeq 80220/80221/80223 PHYs 550 tlphy* at mii? phy ? # ThunderLAN PHYs 551 ukphy* at mii? phy ? # generic unknown PHYs 552 553 ## Loopback network interface; required 554 pseudo-device loop 555 556 ## SLIP and CSLIP interfaces, for IP over a serial line. 557 pseudo-device sl 558 559 ## PPP, the successor to SLIP. See pppd(8). 560 pseudo-device ppp 561 562 ## PPP over Ethernet (RFC 2516) 563 pseudo-device pppoe 564 565 ## Starmode Radio IP, a special hardware network device. 566 #pseudo-device strip 567 568 ## Network "tunnel" device, allowing protocol stacks to run in the userland. 569 ## This is used by the third-party user-mode "ppp" program, and others. 570 pseudo-device tun 571 pseudo-device tap # virtual Ethernet 572 573 ## Generic L3 over IP tunnel 574 #pseudo-device gre # generic L3 over IP tunnel 575 576 ## Berkeley Packet Filter, required to run RARPD. A generic C-language 577 ## interface that allows selective examining of incoming packets. 578 pseudo-device bpfilter 579 580 #pseudo-device carp # Common Address Redundancy Protocol 581 582 pseudo-device npf # NPF packet filter 583 584 ## for IPv6 585 pseudo-device gif # IPv[46] over IPv[46] tunnel (RFC1933) 586 #pseudo-device faith # IPv[46] tcp relay translation i/f 587 pseudo-device stf # 6to4 IPv6 over IPv4 encapsulation 588 589 ## IEEE 802.1Q Virtual LAN encapsulation, see vlan(4). 590 pseudo-device vlan 591 592 ## Simple inter-network traffic bridging 593 pseudo-device bridge 594 #options BRIDGE_IPF # bridge uses IP/IPv6 pfil hooks too 595 pseudo-device agr # IEEE 802.3ad link aggregation 596 597 ## accept filters 598 pseudo-device accf_data # "dataready" accept filter 599 pseudo-device accf_http # "httpready" accept filter 600 601 #### Audio and video devices 602 603 ## /dev/audio support (`audioamd' plus `audio') 604 ## 605 audioamd0 at mainbus0 # sun4c 606 audioamd0 at obio0 # sun4m 607 audioamd0 at sbus0 slot ? offset ? # sun4m 608 609 audiocs0 at sbus0 slot ? offset ? # SUNW,CS4231 610 611 #options DBRI_DEBUG # noisy debug output from the dbri driver 612 #options DBRI_BIG_BUFFER # use bigger DMA buffers, for slow CPUs 613 dbri* at sbus? slot ? offset ? # SUNW,DBRI[s3|e] 614 615 audio* at audiobus? 616 617 ## Sun "bwtwo" black and white framebuffer, found on sun4, sun4c, and sun4m 618 ## systems. If your sun4 system has a cgfour installed in the P4 slot, 619 ## the P4 entries for "bwtwo" will attach to the overlay plane of the 620 ## "cgfour". 621 622 bwtwo0 at sbus0 slot ? offset ? # sun4c and sun4m 623 bwtwo* at sbus? slot ? offset ? # 624 bwtwo0 at obio0 addr 0xfd000000 level 4 # sun4/200 625 bwtwo0 at obio0 addr 0xfb300000 level 4 # sun4/300 in P4 slot 626 bwtwo0 at obio0 addr 0x0b300000 level 4 # sun4/100 in P4 slot 627 628 ## Sun "cgtwo" VME color framebuffer 629 # XXX no wsdisplay support 630 #cgtwo0 at vme0 addr 0x400000 irq ? vect 0xa8 631 632 ## Sun "cgthree" Sbus color framebuffer 633 cgthree0 at sbus? slot ? offset ? 634 cgthree* at sbus? slot ? offset ? 635 636 ## Sun "cgfour" color framebuffer with overlay plane. See above comment 637 ## regarding overlay plane. 638 # XXX no wsdisplay support 639 #cgfour0 at obio0 addr 0xfb300000 level 4 # sun4/300 P4 640 #cgfour0 at obio0 addr 0x0b300000 level 4 # sun4/100 P4 641 642 ## Sun "cgsix" accelerated color framebuffer. 643 cgsix0 at sbus? slot ? offset ? 644 cgsix* at sbus? slot ? offset ? 645 cgsix0 at obio0 addr 0xfb000000 level 4 # sun4/300 P4 646 cgsix0 at obio0 addr 0x0b000000 level 4 # sun4/100 P4 647 648 ## Sun "cgeight" 24-bit framebuffer 649 # XXX no wsdisplay support 650 #cgeight0 at obio0 addr 0xfb300000 level 4 # sun4/300 P4 651 #cgeight0 at obio0 addr 0x0b300000 level 4 # sun4/100 P4 652 653 ## Sun "tcx" accelerated color framebuffer. 654 # there can be only one 655 tcx0 at sbus? slot ? offset ? 656 657 ## Sun CG12 / Matrox SG3 accelerated 24bit framebuffer 658 cgtwelve* at sbus? slot ? offset ? 659 # the driver can use the color framebuffer or the monochrome overlay 660 # the latter is faster 661 options CG12_COLOR 662 663 # Sun "cgfourteen" accelerated 24-bit framebuffer. 664 cgfourteen* at obio0 # sun4m 665 666 # P9100-based display on Tadpole SPARCbook 3. 667 pnozz0 at sbus? slot ? offset ? 668 # the SPARCbook 3 hardware docs say that accesses to P9100 registers need to be 669 # 'latched in' but at least my 3GX works happily without 670 # Enable it by default since we don't know which hardware really needs it. 671 options PNOZZ_USE_LATCH 672 673 # Sun ZX/Leo 24-bit framebuffer 674 zx* at sbus? slot ? offset ? 675 676 # Fujitsu AG-10e accelerated graphics 8/24-bit board 677 agten* at sbus? slot ? offset ? 678 679 ## Southland Media Systems (now Quantum 3D) MGX 680 mgx* at sbus? slot ? offset ? 681 682 # generic framebuffer console 683 genfb* at sbus? slot ? offset ? 684 685 # make sure wsdisplay0 is the console 686 wsdisplay0 at wsemuldisplaydev? console 1 687 wsdisplay* at wsemuldisplaydev? 688 689 #### Other device configuration 690 691 # Tadpole microcontroller 692 tctrl0 at obio0 693 694 # Aurora Personality Chip (APC) on SPARCstation-4/5 695 # Not enabled by default as it may hang some systems 696 #apc* at sbus? slot ? offset ? 697 698 ## Pseudo ttys, required for network logins and programs like screen. 699 700 pseudo-device pty # pseudo-terminals 701 702 ## Random device, used to implement /dev/random (a source of random noise), 703 ## and generate randomness for some kernel formulae. 704 705 706 # a pseudo device needed for Coda # also needs CODA (above) 707 pseudo-device vcoda # coda minicache <-> venus comm. 708 709 pseudo-device clockctl # user control of clock subsystem 710 pseudo-device drvctl # user control of drive subsystem 711 pseudo-device ksyms # /dev/ksyms 712 pseudo-device fss # file system snapshot device 713 pseudo-device wsmux # mouse and keyboard multiplexor 714 pseudo-device wsfont 715 pseudo-device putter # for puffs and pud 716 717 #options FILEASSOC # fileassoc(9) - required for Veriexec 718 # and PAX_SEGVGUARD 719 720 # Veriexec 721 # 722 # a pseudo device needed for veriexec 723 #pseudo-device veriexec 724 # 725 # Uncomment the fingerprint methods below that are desired. Note that 726 # removing fingerprint methods will have almost no impact on the kernel 727 # code size. 728 # 729 #options VERIFIED_EXEC_FP_SHA256 730 #options VERIFIED_EXEC_FP_SHA384 731 #options VERIFIED_EXEC_FP_SHA512 732 733 #options PAX_MPROTECT=0 # PaX mprotect(2) restrictions 734 # (for static binaries only for now) 735
Indexes created Thu Oct 02 10:09:58 GMT 2025