GENERIC revision 1.58
1# $NetBSD: GENERIC,v 1.58 1998/01/25 19:56:31 pk Exp $ 2 3include "arch/sparc/conf/std.sparc" 4 5maxusers 32 6 7## System kernel configuration. See options(4) for more detail. 8 9 10# Options for variants of the Sun SPARC architecure. 11# We currently support three architecture types; at least one is required. 12options SUN4 # sun4/100, sun4/200, sun4/300 13options SUN4C # sun4c - SS1, 1+, 2, ELC, SLC, IPC, IPX, etc. 14options SUN4M # sun4m - SS10, SS20, Classic, etc. 15 16#options MMU_3L # 3-level MMU on sun4/400; (incomplete) 17 18## System options specific to the sparc machine type 19 20# Blink the power LED on some machines to indicate the system load. 21#options BLINK 22 23## Use a faster console than the PROM's slow drawing routines. Not needed 24## for headless (no framebuffer) machines. 25options RASTERCONSOLE # fast rasterop console 26 27 28#### System options that are the same for all ports 29 30## Root device configuration: change the ?'s if you are going to use a 31## nonstandard root partition (other than where the kernel is booted from) 32## and/or nonstandard root type (not ffs or nfs). Normally this can be 33## automagically determined at boot time. 34 35config netbsd root on ? type ? 36 37## System call tracing (see ktrace(1)). 38options KTRACE 39 40## Collect statistics on kernel malloc's and free's. This does have a 41## significant performance hit on slower machines, so it is intended for 42## diagnostic use only. 43#options KMEMSTATS 44 45## System V compatible IPC subsystem. (msgctl(2), semctl(2), and shmctl(2)) 46options SYSVMSG # System V message queues 47options SYSVSEM # System V semaphores 48options SYSVSHM # System V shared memory 49#options SHMMAXPGS=1024 # 1024 pages is the default 50 51## Loadable kernel module support; still under development. 52options LKM 53 54 55#### Debugging options 56 57## The DDB in-kernel debugger runs at panic (unless DDB_ONPANIC=0), or at 58## serial console break or keyboard reset, where the PROM would normally 59## intercept. DDB_HISTORY_SIZE adds up/down arrow command history. 60#options DDB # kernel dynamic debugger 61#options DDB_HISTORY_SIZE=100 # enable history editing in DDB 62#options DDB_ONPANIC # see also sysctl(8): `ddb.onpanic' 63 64## You may also use gdb, on another computer connected to this machine over 65## a serial port. Both KGDBDEV and KGDBRATE should be specified; KGDBDEV is 66## a dev_t encoded device number of the serial port to use. 67## (0xc01 = ttya, 0xc02 = ttyb.) 68#options KGDB # support for kernel gdb 69#options KGDBDEV=0xc01 # kgdb device number (this sample is `ttyb') 70#options KGDBRATE=38400 # baud rate 71 72 73## Compile the kernel with debugging symbols (`netbsd.gdb' is the debug file), 74## such that gdb(1) can be used on a kernel coredump. 75 76#makeoptions DEBUG="-g" 77 78 79## Adds code to the kernel that does internal consistency checks, and will 80## cause the kernel to panic if corruption of internal data structures 81## is detected. 82#options DIAGNOSTIC # extra kernel sanity checking 83 84## Enable (possibly expensive) debugging code that may also display messages 85## on the system console 86#options DEBUG 87 88## Make SCSI error messages more verbose when explaining their meanings. 89options SCSIVERBOSE 90 91## `INSECURE' turns off the kernel security level (securelevel = 0 always). 92## This allows writing to /dev/mem, loading kernel modules while multi-user, 93## and other insecurities good only for development work. Do not use this 94## option on a production machine. 95#options INSECURE 96 97## Allow non-root users to grab /dev/console with programs such as xconsole. 98## `xconsole' therefore does not need setuid root with this option enabled. 99#options UCONSOLE 100 101## `FDSCRIPTS' allows non-readable but executable scripts by providing a 102## pre-opened opaque file to the script interpreter. `SETUIDSCRIPTS', 103## which implies FDSCRIPTS, allows scripts to be set-user-id using the same 104## opaque file mechanism. Perl calls this "secure setuid scripts." 105 106#options FDSCRIPTS 107#options SETUIDSCRIPTS 108 109## Options for compatibility with previous releases foreign system binaries. 110## In the cases of COMPAT_SUNOS and COMPAT_SVR4, you may need to set up 111## additional user-level utilities or system configuration files. See 112## compat_sunos(8) and compat_svr4(8). 113 114options COMPAT_43 # 4.3BSD system interfaces 115options COMPAT_10 # NetBSD 1.0 binary compatibility 116options COMPAT_11 # NetBSD 1.1 binary compatibility 117options COMPAT_12 # NetBSD 1.2 binary compatibility 118options COMPAT_13 # NetBSD 1.3 binary compatibility 119options COMPAT_SUNOS # SunOS 4.x binary compatibility 120options COMPAT_SVR4 # SunOS 5.x binary compatibility 121options EXEC_ELF32 # Exec module for SunOS 5.x binaries. 122 123## File systems. You probably need at least one of FFS or NFS. 124file-system FFS # Berkeley Fast Filesystem 125file-system NFS # Sun NFS-compatible filesystem client 126file-system KERNFS # kernel data-structure filesystem 127file-system NULLFS # NULL layered filesystem 128file-system MFS # memory-based filesystem 129file-system FDESC # user file descriptor filesystem 130file-system UMAPFS # uid/gid remapping filesystem 131file-system LFS # Log-based filesystem (still experimental) 132file-system PORTAL # portal filesystem (still experimental) 133file-system PROCFS # /proc 134file-system CD9660 # ISO 9660 + Rock Ridge file system 135file-system UNION # union file system 136file-system MSDOSFS # MS-DOS FAT filesystem(s). 137 138## File system options. 139options NFSSERVER # Sun NFS-compatible filesystem server 140options QUOTA # FFS quotas 141options FIFO # POSIX fifo support (in all filesystems) 142 143## Network protocol support. In most environments, INET is required. 144options INET # IP (Internet Protocol) v4 145options TCP_COMPAT_42 # 4.2BSD IP implementation compatibility 146#options GATEWAY # packet forwarding ("router switch") 147#options MROUTING # packet forwarding of multicast packets 148#options DIRECTED_BROADCAST # allow broadcasts through routers 149options NS # Xerox NS networking 150#options NSIP # Xerox NS tunneling over IP 151options ISO,TPIP # OSI networking 152options EON # OSI tunneling over IP 153#options CCITT,LLC,HDLC # X.25 packet switched protocol 154options NETATALK # AppleTalk (over Ethernet) protocol 155#options NTP # Network Time Protocol in-kernel support 156#options PPS_SYNC # Add serial line synchronization for NTP 157#options PFIL_HOOKS # Add pfil(9) hooks, intended for custom LKMs. 158#options IPFILTER_LOG # Add ipmon(8) logging for ipfilter device 159#options PPP_BSDCOMP # Add BSD compression to ppp device 160#options PPP_DEFLATE # Add deflate (libz) compression to ppp device 161#options PPP_FILTER # Add active filters for ppp (via bpf) 162 163 164 165#### Main bus and CPU .. all systems. 166mainbus0 at root 167cpu0 at mainbus0 168 169#### Bus types found on SPARC systems. 170 171sbus0 at mainbus0 # sun4c 172obio0 at mainbus0 # sun4 and sun4m 173vme0 at mainbus0 # sun4 174iommu0 at mainbus0 # sun4m 175sbus0 at iommu0 # sun4m 176vme0 at iommu0 # sun4m 177 178#### Standard system devices -- all required for a given architecture 179 180## Auxiliary system registers on sun4c and sun4m 181auxreg0 at mainbus0 # sun4c 182auxreg0 at obio0 # sun4m 183 184## Power status and control register on Sun4m systems 185power0 at obio0 186 187## Mostek clock found on 4/300, sun4c, and sun4m systems. 188## The Mostek clock NVRAM is the "eeprom" on sun4/300 systems. 189clock0 at mainbus0 # sun4c 190clock0 at obio0 # sun4m 191clock0 at obio0 addr 0xf2000000 # sun4/300 192 193## Intersil clock found on 4/100 and 4/200 systems. 194oclock0 at obio0 addr 0xf3000000 # sun4/200 195oclock0 at obio0 addr 0x03000000 # sun4/100 196 197## Memory error registers. 198memreg0 at mainbus0 # sun4c 199memreg0 at obio0 # sun4m 200memreg0 at obio0 addr 0xf4000000 # sun4/200 and sun4/300 201memreg0 at obio0 addr 0x04000000 # sun4/100 202 203## Timer chip found on 4/300, sun4c, and sun4m systems. 204timer0 at mainbus0 # sun4c 205timer0 at obio0 # sun4m 206timer0 at obio0 addr 0xef000000 # sun4/300 207 208## EEPROM found on 4/100 and 4/200 systems. Note that the 4/300 209## doesn't use this driver; the `EEPROM' is in the NVRAM on the 210## Mostek clock chip on 4/300 systems. 211eeprom0 at obio0 addr 0xf2000000 # sun4/200 212eeprom0 at obio0 addr 0x02000000 # sun4/100 213 214 215#### Serial port configuration 216 217## Zilog 8530 serial chips. Each has two-channels. 218## zs0 is ttya and ttyb. zs1 is the keyboard and mouse. 219zs0 at mainbus0 # sun4c 220zs0 at obio0 # sun4m 221zs0 at obio0 addr 0xf1000000 level 12 flags 0x103 # sun4/200 and sun4/300 222zs0 at obio0 addr 0x01000000 level 12 flags 0x103 # sun4/100 223zstty0 at zs0 channel 0 # ttya 224zstty1 at zs0 channel 1 # ttyb 225 226zs1 at mainbus0 # sun4c 227zs1 at obio0 # sun4m 228zs1 at obio0 addr 0xf0000000 level 12 flags 0x103 # sun4/200 and sun4/300 229zs1 at obio0 addr 0x00000000 level 12 flags 0x103 # sun4/100 230kbd0 at zs1 channel 0 # keyboard 231ms0 at zs1 channel 1 # mouse 232 233zs2 at obio0 addr 0xe0000000 level 12 flags 0x103 # sun4/300 234zstty2 at zs2 channel 0 # ttyc 235zstty3 at zs2 channel 1 # ttyd 236 237#### Disk controllers and disks 238 239# 240 241## The following flags may be set for the NCR53c94 based esp driver: 242## bits 0-7: disable disconnect/reselect for the corresponding target 243## bits 8-15: disable synchronous negotiation for target [bit-8] 244 245## sun4/300, sun4c, sun4m on-board SCSI, and FSBE/S SBus SCSI cards. 246## Both `dma' and `esp' are needed in all cases. 247## Two kinds of additional SBus SCSI interfaces are available. One uses 248## "esp at sbus" like the sun4c on-board; the other uses "esp at dma". 249 250## sun4/300 SCSI - an NCR53c94 or equivalent behind 251## an LSI Logic DMA controller 252 253dma0 at obio0 addr 0xfa001000 level 4 # sun4/300 254esp0 at obio0 addr 0xfa000000 level 4 flags 0x0000 # sun4/300 255 256dma0 at sbus0 slot ? offset ? # sun4c/sun4m 257esp0 at sbus0 slot ? offset ? flags 0x0000 # sun4c 258esp0 at dma0 flags 0x0000 # sun4m 259 260# FSBE/S SCSI 261dma* at sbus? slot ? offset ? # SBus 262esp* at sbus? slot ? offset ? flags 0x0000 # SBus (older proms) 263esp* at dma? flags 0x0000 # SBus 264 265scsibus* at esp? 266 267## Qlogic ISP SBus SCSI Card 268isp* at sbus? slot ? offset ? 269scsibus* at isp? 270 271## NCR5380-based "Sun SCSI 3" VME SCSI controller. 272## This driver has several flags which may be enabled by OR'ing 273## the values and using the "flags" directive. 274## Valid flags are: 275## 276## 0x01 Use DMA (may be polled) 277## 0x02 Use DMA completion interrupts 278## 0x04 Allow disconnect/reselect 279## 280## E.g. the following would enable DMA, interrupts, and reselect: 281## si0 at vme0 addr 0x200000 level 3 vect 0x40 flags 0x07 282## 283## By default, DMA is enabled in the driver. 284 285si0 at vme0 addr 0x200000 pri 2 vec 0x40 286scsibus* at si? 287 288## NCR5380-based "SCSI Weird" on-board SCSI interface found 289## on sun4/100 systems. The flags are the same as the "si" 290## controller. Note, while DMA is enabled by default, only 291## polled DMA works at this time, and reselects do not work 292## on this particular controller. 293 294sw0 at obio0 addr 0x0a000000 level 3 295scsibus* at sw? 296 297## These entries find devices on all SCSI busses and assign 298## unit numbers dynamically. 299sd* at scsibus? target ? lun ? # SCSI disks 300st* at scsibus? target ? lun ? # SCSI tapes 301cd* at scsibus? target ? lun ? # SCSI CD-ROMs 302ch* at scsibus? target ? lun ? # SCSI changer devices 303ss* at scsibus? target ? lun ? # SCSI scanners 304uk* at scsibus? target ? lun ? # unknown SCSI 305 306 307## Xylogics 753 or 7053 VME SMD disk controllers and disks, found 308## on sun4 systems. 309xdc0 at vme0 addr 0xffee80 pri 3 vec 0x44 310xdc1 at vme0 addr 0xffee90 pri 3 vec 0x45 311xdc2 at vme0 addr 0xffeea0 pri 3 vec 0x46 312xdc3 at vme0 addr 0xffeeb0 pri 3 vec 0x47 313xd* at xdc? drive ? 314 315## Xylogics 451 or 451 VME SMD disk controllers and disks, found 316## on sun4 systems. 317xyc0 at vme0 addr 0xffee40 pri 3 vec 0x48 318xyc1 at vme0 addr 0xffee48 pri 3 vec 0x49 319xy* at xyc? drive ? 320 321 322## Floppy controller and drive found on SPARCstations. 323 324fdc0 at mainbus0 # sun4c controller 325fdc0 at obio0 # sun4m controller 326fd* at fdc0 # the drive itself 327 328## A disk-like interface to files. Can be used to create floppy, CD, 329## miniroot images, etc. 330 331pseudo-device vnd 4 332 333## Concatenated and striped disks; with this, you can create a software-based 334## disk array similar to a "RAID 0" setup. See ccd(4). 335 336pseudo-device ccd 4 337 338## Memory disk device, used on boot floppies with compressed 339## kernel-plus-root-disk images. 340 341#pseudo-device md 1 342 343 344#### Network interfaces 345 346## LANCE Ethernet - an AMD 7990 LANCE behind specialized DMA glue 347## Three flavors of additional SBus ethernets are available. One attaches 348## directly like the sun4c on-board, one uses the ledma device like the 349## sun4m on-board, and one uses the lebuffer device. 350 351le0 at obio0 addr 0xf9000000 level 6 # sun4/300 352le0 at sbus0 slot ? offset ? # sun4c on-board 353ledma0 at sbus0 slot ? offset ? # sun4m on-board 354le0 at ledma0 # sun4m on-board 355le* at sbus? slot ? offset ? # SBus 356ledma* at sbus? slot ? offset ? # SBus 357le* at ledma? # SBus 358lebuffer0 at sbus? slot ? offset ? # SBus 359le0 at lebuffer? # SBus 360lebuffer* at sbus? slot ? offset ? # SBus 361le* at lebuffer? # SBus 362 363 364## sun4/100 and sun4/200 Ethernet - an Intel 82586 on-board 365## or on a Multibus/VME card. 366ie0 at obio0 addr 0xf6000000 level 6 # sun4/200 on-board 367ie0 at obio0 addr 0x06000000 level 6 # sun4/100 on-board 368ie1 at vme0 addr 0xe88000 pri 3 vec 0x75 # VME 369ie2 at vme0 addr 0x31ff02 pri 3 vec 0x76 # VME 370ie3 at vme0 addr 0x35ff02 pri 3 vec 0x77 # VME 371ie4 at vme0 addr 0x2dff02 pri 3 vec 0x7c # VME 372 373## Loopback network interface; required 374pseudo-device loop 375 376## SLIP and CSLIP interfaces, for IP over a serial line. 377pseudo-device sl 2 378 379## PPP, the successor to SLIP. See pppd(8). 380pseudo-device ppp 2 381 382## Starmode Radio IP, a special hardware network device. 383#pseudo-device strip 1 384 385## Network "tunnel" device, allowing protocol stacks to run in the userland. 386## This is used by the third-party user-mode "ppp" program, and others. 387pseudo-device tun 4 388 389## Berkeley Packet Filter, required to run RARPD. A generic C-language 390## interface that allows selective examining of incoming packets. 391pseudo-device bpfilter 8 392 393## IP Filter, used in firewall and NAT applications. See ipnat(8) for 394## one example of the use of the IP Filter. 395pseudo-device ipfilter 396 397 398#### Audio and video devices 399 400## /dev/audio support (`audioamd' plus `audio') 401## 402audioamd0 at mainbus0 # sun4c 403audioamd0 at obio0 # sun4m 404audioamd0 at sbus0 slot ? offset ? # sun4m 405audio* at audioamd0 406 407 408## Sun "bwtwo" black and white framebuffer, found on sun4, sun4c, and sun4m 409## systems. If your sun4 system has a cgfour installed in the P4 slot, 410## the P4 entries for "bwtwo" will attach to the overlay plane of the 411## "cgfour". 412 413bwtwo0 at sbus0 slot ? offset ? # sun4c and sun4m 414bwtwo* at sbus? slot ? offset ? # 415bwtwo0 at obio0 addr 0xfd000000 level 4 # sun4/200 416bwtwo0 at obio0 addr 0xfb300000 level 4 # sun4/300 in P4 slot 417bwtwo0 at obio0 addr 0x0b300000 level 4 # sun4/100 in P4 slot 418 419## Sun "cgtwo" VME color framebuffer 420cgtwo0 at vme0 addr 0x400000 pri ? vec 0xa8 421 422## Sun "cgthree" Sbus color framebuffer 423cgthree0 at sbus? slot ? offset ? 424cgthree* at sbus? slot ? offset ? 425#cgthree0 at obio? slot ? offset ? # sun4m 426 427## Sun "cgfour" color framebuffer with overlay plane. See above comment 428## regarding overlay plane. 429cgfour0 at obio0 addr 0xfb300000 level 4 # sun4/300 P4 430cgfour0 at obio0 addr 0x0b300000 level 4 # sun4/100 P4 431 432## Sun "cgsix" accelerated color framebuffer. 433cgsix0 at sbus? slot ? offset ? 434cgsix* at sbus? slot ? offset ? 435cgsix0 at obio0 addr 0xfb000000 level 4 # sun4/300 P4 436cgsix0 at obio0 addr 0x0b000000 level 4 # sun4/100 P4 437 438## Sun "cgeight" 24-bit framebuffer 439cgeight0 at obio0 addr 0xfb300000 level 4 # sun4/300 P4 440cgeight0 at obio0 addr 0x0b300000 level 4 # sun4/100 P4 441 442## Sun "tcx" accelerated color framebuffer. 443tcx0 at sbus? slot ? offset ? 444tcx* at sbus? slot ? offset ? 445 446# Sun "cgfourteen" accelerated 24-bit framebuffer. 447cgfourteen0 at obio0 # sun4m 448 449 450#### Other device configuration 451 452## Pseudo ttys, required for network logins and programs like screen. 453## 32 is a good number for average systems; you may have as many as you 454## like, though 256 is more or less the upper limit. Increasing this 455## number still requires you to run /dev/MAKEDEV to create the files 456## for the ptys. 457 458pseudo-device pty 32 # pseudo-ttys (for network, etc.) 459 460## Random device, used to implement /dev/random (a source of random noise), 461## and generate randomness for some kernel formulae. 462## THIS DEVICE IS EXPERIMENTAL; use at your own risk. 463 464#pseudo-device rnd 465