GENERIC revision 1.79
1# 	$NetBSD: GENERIC,v 1.79 1999/04/26 04:25:38 ad Exp $
2
3include "arch/sparc/conf/std.sparc"
4
5maxusers	32
6
7## System kernel configuration.  See options(4) for more detail.
8
9
10# Options for variants of the Sun SPARC architecure.
11# We currently support three architecture types; at least one is required.
12options 	SUN4		# sun4/100, sun4/200, sun4/300
13options 	SUN4C		# sun4c - SS1, 1+, 2, ELC, SLC, IPC, IPX, etc.
14options 	SUN4M		# sun4m - SS10, SS20, Classic, etc.
15
16#options 	SUN4_MMU3L	# 3-level MMU on sun4/400; (incomplete)
17
18## System options specific to the sparc machine type
19
20# Blink the power LED on some machines to indicate the system load.
21#options 	BLINK
22
23## Use a faster console than the PROM's slow drawing routines.  Not needed
24## for headless (no framebuffer) machines.
25options 	RASTERCONSOLE		# fast rasterop console
26options 	FONT_GALLANT12x22	# the console font
27#options 	FONT_BOLD8x16		# a somewhat smaller font
28
29#### System options that are the same for all ports
30
31## Root device configuration: change the ?'s if you are going to use a
32## nonstandard root partition (other than where the kernel is booted from)
33## and/or nonstandard root type (not ffs or nfs).  Normally this can be
34## automagically determined at boot time.
35
36config		netbsd	root on ? type ?
37
38## System call tracing (see ktrace(1)).
39options 	KTRACE
40
41## Collect statistics on kernel malloc's and free's.  This does have a
42## significant performance hit on slower machines, so it is intended for
43## diagnostic use only.
44#options 	KMEMSTATS
45
46## System V compatible IPC subsystem.  (msgctl(2), semctl(2), and shmctl(2))
47options 	SYSVMSG		# System V message queues
48options 	SYSVSEM		# System V semaphores
49options 	SYSVSHM		# System V shared memory
50#options 	SHMMAXPGS=1024	# 1024 pages is the default
51
52## Loadable kernel module support; still under development.
53options 	LKM
54
55## NFS boot options; default on sparc is the bootparam protocol
56options 	NFS_BOOT_BOOTPARAM
57#options 	NFS_BOOT_BOOTP
58#options 	NFS_BOOT_DHCP
59
60#### Debugging options
61
62## The DDB in-kernel debugger runs at panic (unless DDB_ONPANIC=0), or at
63## serial console break or keyboard reset, where the PROM would normally
64## intercept.  DDB_HISTORY_SIZE adds up/down arrow command history.
65#options 	DDB			# kernel dynamic debugger
66#options 	DDB_HISTORY_SIZE=100	# enable history editing in DDB
67#options 	DDB_ONPANIC=1		# see also sysctl(8): `ddb.onpanic'
68
69## You may also use gdb, on another computer connected to this machine over
70## a serial port.  Both KGDBDEV and KGDBRATE should be specified; KGDBDEV is
71## a dev_t encoded device number of the serial port to use.
72## (0xc01 = ttya, 0xc02 = ttyb.)
73#options 	KGDB		# support for kernel gdb
74#options 	KGDBDEV=0xc01	# kgdb device number (this sample is `ttyb')
75#options 	KGDBRATE=38400	# baud rate
76
77
78## Compile the kernel with debugging symbols (`netbsd.gdb' is the debug file),
79## such that gdb(1) can be used on a kernel coredump.
80
81#makeoptions 	DEBUG="-g"
82
83
84## Adds code to the kernel that does internal consistency checks, and will
85## cause the kernel to panic if corruption of internal data structures
86## is detected.
87#options 	DIAGNOSTIC	# extra kernel sanity checking
88
89## Enable (possibly expensive) debugging code that may also display messages
90## on the system console
91#options 	DEBUG
92
93## Make SCSI error messages more verbose when explaining their meanings.
94options 	SCSIVERBOSE
95
96## `INSECURE' turns off the kernel security level (securelevel = 0 always).
97## This allows writing to /dev/mem, loading kernel modules while multi-user,
98## and other insecurities good only for development work.  Do not use this
99## option on a production machine.
100#options 	INSECURE
101
102## Allow non-root users to grab /dev/console with programs such as xconsole.
103## `xconsole' therefore does not need setuid root with this option enabled.
104#options 	UCONSOLE
105
106## `FDSCRIPTS' allows non-readable but executable scripts by providing a
107## pre-opened opaque file to the script interpreter.  `SETUIDSCRIPTS',
108## which implies FDSCRIPTS, allows scripts to be set-user-id using the same
109## opaque file mechanism.  Perl calls this "secure setuid scripts."
110
111#options 	FDSCRIPTS
112#options 	SETUIDSCRIPTS
113
114## Options for compatibility with previous releases foreign system binaries.
115## In the cases of COMPAT_SUNOS and COMPAT_SVR4, you may need to set up
116## additional user-level utilities or system configuration files. See
117## compat_sunos(8) and compat_svr4(8).
118
119options 	COMPAT_43	# 4.3BSD system interfaces
120options 	COMPAT_10	# NetBSD 1.0 binary compatibility
121options 	COMPAT_11	# NetBSD 1.1 binary compatibility
122options 	COMPAT_12	# NetBSD 1.2 binary compatibility
123options 	COMPAT_13	# NetBSD 1.3 binary compatibility
124options 	COMPAT_SUNOS	# SunOS 4.x binary compatibility
125options 	COMPAT_SVR4	# SunOS 5.x binary compatibility
126options 	EXEC_ELF32	# Exec module for SunOS 5.x binaries.
127
128## File systems.  You probably need at least one of FFS or NFS.
129file-system	FFS		# Berkeley Fast Filesystem
130file-system	NFS		# Sun NFS-compatible filesystem client
131file-system	KERNFS		# kernel data-structure filesystem
132file-system	NULLFS		# NULL layered filesystem
133file-system	MFS		# memory-based filesystem
134file-system	FDESC		# user file descriptor filesystem
135file-system	UMAPFS		# uid/gid remapping filesystem
136file-system	LFS		# Log-based filesystem (still experimental)
137file-system	PORTAL		# portal filesystem (still experimental)
138file-system	PROCFS		# /proc
139file-system	CD9660		# ISO 9660 + Rock Ridge file system
140file-system	UNION		# union file system
141file-system	MSDOSFS		# MS-DOS FAT filesystem(s).
142
143## File system options.
144options 	NFSSERVER	# Sun NFS-compatible filesystem server
145options 	QUOTA		# FFS quotas
146#options 	FFS_EI		# FFS Endian Independent support
147
148## Network protocol support.  In most environments, INET is required.
149options 	INET		# IP (Internet Protocol) v4
150options 	TCP_COMPAT_42	# 4.2BSD IP implementation compatibility
151#options 	GATEWAY		# packet forwarding ("router switch")
152#options 	MROUTING	# packet forwarding of multicast packets
153#options 	DIRECTED_BROADCAST	# allow broadcasts through routers
154options 	NS		# Xerox NS networking
155#options 	NSIP		# Xerox NS tunneling over IP
156options 	ISO,TPIP	# OSI networking
157options 	EON		# OSI tunneling over IP
158#options 	CCITT,LLC,HDLC	# X.25 packet switched protocol
159#options 	NETATALK	# AppleTalk (over Ethernet) protocol
160options 	NTP		# Network Time Protocol in-kernel support
161#options 	PPS_SYNC	# Add serial line synchronization for NTP
162#options 	PFIL_HOOKS	# Add pfil(9) hooks, intended for custom LKMs.
163#options 	IPFILTER_LOG	# Add ipmon(8) logging for ipfilter device
164#options 	PPP_BSDCOMP	# Add BSD compression to ppp device
165#options 	PPP_DEFLATE	# Add deflate (libz) compression to ppp device
166#options 	PPP_FILTER	# Add active filters for ppp (via bpf)
167
168
169
170#### Main bus and CPU .. all systems.
171mainbus0 at root
172cpu0	at mainbus0
173
174#### Bus types found on SPARC systems.
175
176sbus0	at mainbus0				# sun4c
177obio0	at mainbus0				# sun4 and sun4m
178vme0	at mainbus0				# sun4
179iommu0	at mainbus0				# sun4m
180sbus0	at iommu0				# sun4m
181vme0	at iommu0				# sun4m
182
183## SBus expander box
184xbox*	at sbus? slot ? offset ?
185sbus*	at xbox?
186
187## SBus to PCMCIA bridge
188nell*	at sbus? slot ? offset ?		# PCMCIA bridge
189pcmcia*	at nell?
190
191#### Standard system devices -- all required for a given architecture
192
193## Auxiliary system registers on sun4c and sun4m
194auxreg0	at mainbus0				# sun4c
195auxreg0	at obio0				# sun4m
196
197## Power status and control register on Sun4m systems
198power0	at obio0
199
200## Mostek clock found on 4/300, sun4c, and sun4m systems.
201## The Mostek clock NVRAM is the "eeprom" on sun4/300 systems.
202clock0	at mainbus0				# sun4c
203clock0	at obio0				# sun4m
204clock0	at obio0 addr 0xf2000000		# sun4/300
205
206## Intersil clock found on 4/100 and 4/200 systems.
207oclock0	at obio0 addr 0xf3000000		# sun4/200
208oclock0	at obio0 addr 0x03000000		# sun4/100
209
210## Memory error registers.
211memreg0	at mainbus0				# sun4c
212memreg0	at obio0				# sun4m
213memreg0	at obio0 addr 0xf4000000		# sun4/200 and sun4/300
214memreg0	at obio0 addr 0x04000000		# sun4/100
215
216## ECC memory control
217eccmemctl0 at mainbus0				# sun4m
218
219## Timer chip found on 4/300, sun4c, and sun4m systems.
220timer0	at mainbus0				# sun4c
221timer0	at obio0				# sun4m
222timer0	at obio0 addr 0xef000000		# sun4/300
223
224## EEPROM found on 4/100 and 4/200 systems.  Note that the 4/300
225## doesn't use this driver; the `EEPROM' is in the NVRAM on the
226## Mostek clock chip on 4/300 systems.
227eeprom0	at obio0 addr 0xf2000000		# sun4/200
228eeprom0	at obio0 addr 0x02000000		# sun4/100
229
230
231#### Serial port configuration
232
233## Zilog 8530 serial chips.  Each has two-channels.
234## zs0 is ttya and ttyb.  zs1 is the keyboard and mouse.
235zs0	at mainbus0					# sun4c
236zs0	at obio0					# sun4m
237zs0	at obio0 addr 0xf1000000 level 12 flags 0x103	# sun4/200 and sun4/300
238zs0	at obio0 addr 0x01000000 level 12 flags 0x103	# sun4/100
239zstty0	at zs0 channel 0	# ttya
240zstty1	at zs0 channel 1	# ttyb
241
242zs1	at mainbus0					# sun4c
243zs1	at obio0					# sun4m
244zs1	at obio0 addr 0xf0000000 level 12 flags 0x103	# sun4/200 and sun4/300
245zs1	at obio0 addr 0x00000000 level 12 flags 0x103	# sun4/100
246kbd0	at zs1 channel 0	# keyboard
247ms0	at zs1 channel 1	# mouse
248
249zs2	at obio0 addr 0xe0000000 level 12 flags 0x103	# sun4/300
250zstty2	at zs2 channel 0	# ttyc
251zstty3	at zs2 channel 1	# ttyd
252
253
254## Magma Serial/Parallel driver
255magma*	at sbus? slot ? offset ?
256mtty*	at magma?
257mbpp*	at magma?
258
259## PCMCIA serial interfaces
260com*	at pcmcia?
261pcmcom*	at pcmcia?
262com*	at pcmcom?
263
264#### Disk controllers and disks
265
266#
267
268## The following flags may be set for the NCR53c94 based esp driver:
269##	bits 0-7:  disable disconnect/reselect for the corresponding target
270##	bits 8-15: disable synchronous negotiation for target [bit-8]
271
272## sun4/300, sun4c, sun4m on-board SCSI, and FSBE/S SBus SCSI cards.
273## Both `dma' and `esp' are needed in all cases.
274## Two kinds of additional SBus SCSI interfaces are available.  One uses
275## "esp at sbus" like the sun4c on-board; the other uses "esp at dma".
276
277## sun4/300 SCSI - an NCR53c94 or equivalent behind
278## an LSI Logic DMA controller
279
280dma0	at obio0 addr 0xfa001000 level 4		# sun4/300
281esp0	at obio0 addr 0xfa000000 level 4 flags 0x0000	# sun4/300
282
283dma0	at sbus0 slot ? offset ?			# sun4c/sun4m
284esp0	at sbus0 slot ? offset ? flags 0x0000		# sun4c
285esp0	at dma0 flags 0x0000				# sun4m
286
287# FSBE/S SCSI
288dma*	at sbus? slot ? offset ?			# SBus
289esp*	at sbus? slot ? offset ? flags 0x0000		# SBus (older proms)
290esp*	at dma? flags 0x0000				# SBus
291
292scsibus* at esp?
293
294## Qlogic ISP SBus SCSI Card
295isp*	at sbus? slot ? offset ?
296scsibus* at isp?
297
298## NCR5380-based "Sun SCSI 3" VME SCSI controller.
299## This driver has several flags which may be enabled by OR'ing
300## the values and using the "flags" directive.
301## Valid flags are:
302##
303##	0x01		Use DMA (may be polled)
304##	0x02		Use DMA completion interrupts
305##	0x04		Allow disconnect/reselect
306##
307## E.g. the following would enable DMA, interrupts, and reselect:
308## si0	at vme0 addr 0x200000 level 3 vect 0x40 flags 0x07
309##
310## By default, DMA is enabled in the driver.
311
312si0	at vme0 addr 0x200000 pri 2 vec 0x40
313scsibus* at si?
314
315## NCR5380-based "SCSI Weird" on-board SCSI interface found
316## on sun4/100 systems.  The flags are the same as the "si"
317## controller.  Note, while DMA is enabled by default, only
318## polled DMA works at this time, and reselects do not work
319## on this particular controller.
320
321sw0	at obio0 addr 0x0a000000 level 3
322scsibus* at sw?
323
324## PCMCIA SCSI controllers
325aic*	at pcmcia?
326scsibus* at aic?
327
328
329## These entries find devices on all SCSI busses and assign
330## unit numbers dynamically.
331sd*	at scsibus? target ? lun ?		# SCSI disks
332st*	at scsibus? target ? lun ?		# SCSI tapes
333cd*	at scsibus? target ? lun ?		# SCSI CD-ROMs
334ch*	at scsibus? target ? lun ?		# SCSI changer devices
335ss*	at scsibus? target ? lun ?		# SCSI scanners
336uk*	at scsibus? target ? lun ?		# unknown SCSI
337
338
339## Xylogics 753 or 7053 VME SMD disk controllers and disks, found
340## on sun4 systems.
341xdc0	at vme0 addr 0xee80 pri 3 vec 0x44
342xdc1	at vme0 addr 0xee90 pri 3 vec 0x45
343xdc2	at vme0 addr 0xeea0 pri 3 vec 0x46
344xdc3	at vme0 addr 0xeeb0 pri 3 vec 0x47
345xd*	at xdc? drive ?
346
347## Xylogics 451 or 451 VME SMD disk controllers and disks, found
348## on sun4 systems.
349xyc0	at vme0 addr 0xee40 pri 3 vec 0x48
350xyc1	at vme0 addr 0xee48 pri 3 vec 0x49
351xy*	at xyc? drive ?
352
353
354## Floppy controller and drive found on SPARCstations.
355
356fdc0	at mainbus0				# sun4c controller
357fdc0	at obio0				# sun4m controller
358fd*	at fdc0					# the drive itself
359
360## PCMCIA IDE controllers
361wdc*	at pcmcia?
362wd*	at wdc?
363
364## A disk-like interface to files.  Can be used to create floppy, CD,
365## miniroot images, etc.
366
367pseudo-device	vnd	4
368
369## Concatenated and striped disks; with this, you can create a software-based
370## disk array similar to a "RAID 0" setup.  See ccd(4).
371
372pseudo-device	ccd	4
373
374## RAIDframe disk driver: software RAID driver.  See raid(4).
375
376#pseudo-device	raid	4
377
378## Memory disk device, used on boot floppies with compressed
379## kernel-plus-root-disk images.
380
381#pseudo-device	md	1
382
383
384#### Network interfaces
385
386## LANCE Ethernet - an AMD 7990 LANCE behind specialized DMA glue
387## Three flavors of additional SBus ethernets are available.  One attaches
388## directly like the sun4c on-board, one uses the ledma device like the
389## sun4m on-board, and one uses the lebuffer device.
390
391le0		at obio0 addr 0xf9000000 level 6	# sun4/300
392le0		at sbus0 slot ? offset ?		# sun4c on-board
393ledma0		at sbus0 slot ? offset ?		# sun4m on-board
394le0		at ledma0				# sun4m on-board
395le*		at sbus? slot ? offset ?		# SBus
396ledma*		at sbus? slot ? offset ?		# SBus
397le*		at ledma?				# SBus
398lebuffer0	at sbus? slot ? offset ?		# SBus
399le0		at lebuffer?				# SBus
400lebuffer*	at sbus? slot ? offset ?		# SBus
401le*		at lebuffer?				# SBus
402
403
404## sun4/100 and sun4/200 Ethernet - an Intel 82586 on-board
405## or on a Multibus/VME card.
406ie0	at obio0 addr 0xf6000000 level 6		# sun4/200 on-board
407ie0	at obio0 addr 0x06000000 level 6		# sun4/100 on-board
408ie1	at vme0 addr 0xe88000 pri 3 vec 0x75		# VME
409ie2	at vme0 addr 0x31ff02 pri 3 vec 0x76		# VME
410ie3	at vme0 addr 0x35ff02 pri 3 vec 0x77		# VME
411ie4	at vme0 addr 0x2dff02 pri 3 vec 0x7c		# VME
412
413## qec/be, qec/hme
414qec*		at sbus? slot ? offset ?
415be*		at qec?
416qe*		at qec?
417
418# midway ATM
419en0	at sbus? slot ? offset ?
420
421# PCMCIA ethernet devices
422ep*	at pcmcia?
423mbe*	at pcmcia?
424ne*	at pcmcia?
425sm*	at pcmcia?
426
427# MII/PHY support
428exphy*	at mii? phy ?			# 3Com internal PHYs
429icsphy*	at mii? phy ?			# Integrated Circuit Systems ICS1890
430inphy*	at mii? phy ?			# Intel 82555 PHYs
431lxtphy*	at mii? phy ?			# Level One LXT-970 PHYs
432nsphy*	at mii? phy ?			# NS83840 PHYs
433qsphy*	at mii? phy ?			# Quality Semiconductor QS6612 PHYs
434sqphy*	at mii? phy ?			# Seeq 80220/80221/80223 PHYs
435tlphy*	at mii? phy ?			# ThunderLAN PHYs
436ukphy*	at mii? phy ?			# generic unknown PHYs
437
438## Loopback network interface; required
439pseudo-device	loop
440
441## SLIP and CSLIP interfaces, for IP over a serial line.
442pseudo-device	sl		2
443
444## PPP, the successor to SLIP.  See pppd(8).
445pseudo-device	ppp		2
446
447## Starmode Radio IP, a special hardware network device.
448#pseudo-device	strip		1
449
450## Network "tunnel" device, allowing protocol stacks to run in the userland.
451## This is used by the third-party user-mode "ppp" program, and others.
452pseudo-device	tun		4
453
454## Generic L3 over IP tunnel
455#pseudo-device	gre		2	# generic L3 over IP tunnel
456
457## Berkeley Packet Filter, required to run RARPD.  A generic C-language
458## interface that allows selective examining of incoming packets.
459pseudo-device	bpfilter	8
460
461## IP Filter, used in firewall and NAT applications.  See ipnat(8) for
462## one example of the use of the IP Filter.
463pseudo-device	ipfilter
464
465
466#### Audio and video devices
467
468## /dev/audio support (`audioamd' plus `audio')
469##
470audioamd0	at mainbus0				# sun4c
471#audioamd0	at obio0				# sun4m
472audioamd0	at sbus0 slot ? offset ?		# sun4m
473audio*		at audioamd0
474
475audiocs0	at sbus0 slot ? offset ?		# SUNW,CS4231
476audio*		at audiocs0
477
478
479## Sun "bwtwo" black and white framebuffer, found on sun4, sun4c, and sun4m
480## systems.  If your sun4 system has a cgfour installed in the P4 slot,
481## the P4 entries for "bwtwo" will attach to the overlay plane of the
482## "cgfour".
483
484bwtwo0		at sbus0 slot ? offset ?		# sun4c and sun4m
485bwtwo*		at sbus? slot ? offset ?		#
486bwtwo0		at obio0 addr 0xfd000000 level 4	# sun4/200
487bwtwo0		at obio0 addr 0xfb300000 level 4	# sun4/300 in P4 slot
488bwtwo0		at obio0 addr 0x0b300000 level 4	# sun4/100 in P4 slot
489
490## Sun "cgtwo" VME color framebuffer
491cgtwo0		at vme0 addr 0x400000 pri ? vec 0xa8
492
493## Sun "cgthree" Sbus color framebuffer
494cgthree0	at sbus? slot ? offset ?
495cgthree*	at sbus? slot ? offset ?
496#cgthree0	at obio? slot ? offset ?		# sun4m
497
498## Sun "cgfour" color framebuffer with overlay plane.  See above comment
499## regarding overlay plane.
500cgfour0		at obio0 addr 0xfb300000 level 4	# sun4/300 P4
501cgfour0		at obio0 addr 0x0b300000 level 4	# sun4/100 P4
502
503## Sun "cgsix" accelerated color framebuffer.
504cgsix0		at sbus? slot ? offset ?
505cgsix*		at sbus? slot ? offset ?
506cgsix0		at obio0 addr 0xfb000000 level 4	# sun4/300 P4
507cgsix0		at obio0 addr 0x0b000000 level 4	# sun4/100 P4
508
509## Sun "cgeight" 24-bit framebuffer
510cgeight0 	at obio0 addr 0xfb300000 level 4	# sun4/300 P4
511cgeight0	at obio0 addr 0x0b300000 level 4	# sun4/100 P4
512
513## Sun "tcx" accelerated color framebuffer.
514tcx0		at sbus? slot ? offset ?
515tcx*		at sbus? slot ? offset ?
516
517# Sun "cgfourteen" accelerated 24-bit framebuffer.
518cgfourteen0	at obio0			# sun4m
519
520
521#### Other device configuration
522
523## Pseudo ttys, required for network logins and programs like screen.
524## 32 is a good number for average systems; you may have as many as you
525## like, though 256 is more or less the upper limit.  Increasing this
526## number still requires you to run /dev/MAKEDEV to create the files
527## for the ptys.
528
529pseudo-device	pty		32	# pseudo-ttys (for network, etc.)
530
531## Random device, used to implement /dev/random (a source of random noise),
532## and generate randomness for some kernel formulae.
533## THIS DEVICE IS EXPERIMENTAL; use at your own risk.
534
535#pseudo-device	rnd
536