INSTALL revision 1.103
1# $NetBSD: INSTALL,v 1.103 2020/01/19 01:25:07 thorpej Exp $ 2# 3# from: NetBSD: GENERIC,v 1.84 1999/06/06 13:00:03 mrg Exp 4# 5# floppy install kernel. try to keep this in sync with GENERIC but 6# leave as much disabled as possible. 7 8include "arch/sparc/conf/std.sparc" 9 10#options INCLUDE_CONFIG_FILE # embed config file in kernel binary 11 12makeoptions COPTS="-Os" # Optimise for space. Implies -O2 13 14maxusers 32 15 16# Enable the hooks used for initializing the root memory-disk. 17options MEMORY_DISK_HOOKS 18options MEMORY_DISK_IS_ROOT # force root on memory disk 19options MEMORY_DISK_SERVER=0 # no userspace memory disk support 20## The miniroot size must be kept in sync manually with the size of 21## the `ramdisk' image (which is built in distrib/sparc/ramdisk). 22options MEMORY_DISK_ROOT_SIZE=2000 # size of memory disk, in blocks 23options MEMORY_DISK_RBFLAGS=RB_SINGLE # boot in single-user mode 24 25pseudo-device md # memory disk device (ramdisk) 26 27## System kernel configuration. See options(4) for more detail. 28 29 30# Options for variants of the Sun SPARC architecure. 31# We currently support three architecture types; at least one is required. 32options SUN4 # sun4/100, sun4/200, sun4/300 33options SUN4C # sun4c - SS1, 1+, 2, ELC, SLC, IPC, IPX, etc. 34options SUN4M # sun4m - SS10, SS20, Classic, etc. 35 36options SUN4_MMU3L # 3-level MMU on sun4/400 37 38## System options specific to the sparc machine type 39 40# Blink the power LED on some machines to indicate the system load. 41#options BLINK 42 43# wscons stuff 44#options WSEMUL_SUN 45options WSEMUL_VT100 46options WSDISPLAY_DEFAULTSCREENS=1 47#options WSDISPLAY_COMPAT_USL # wsconscfg VT handling 48options WSDISPLAY_COMPAT_RAWKBD 49options WSDISPLAY_CUSTOM_OUTPUT 50options WS_DEFAULT_FG=WSCOL_BLACK 51options WS_DEFAULT_BG=WSCOL_LIGHT_WHITE 52options WS_KERNEL_FG=WSCOL_GREEN 53options WS_KERNEL_BG=WSCOL_LIGHT_WHITE 54options FONT_GALLANT12x22 # the console font 55options FONT_BOLD8x16 # a somewhat smaller font 56 57#### System options that are the same for all ports 58 59## Root device configuration: change the ?'s if you are going to use a 60## nonstandard root partition (other than where the kernel is booted from) 61## and/or nonstandard root type (not ffs or nfs). Normally this can be 62## automagically determined at boot time. 63 64config netbsd root on ? type ? 65 66## System call tracing (see ktrace(1)). 67#options KTRACE 68 69## System V compatible IPC subsystem. (msgctl(2), semctl(2), and shmctl(2)) 70#options SYSVMSG # System V message queues 71#options SYSVSEM # System V semaphores 72#options SYSVSHM # System V shared memory 73 74options USERCONF # userconf(4) support 75options PIPE_SOCKETPAIR # smaller, but slower pipe(2) 76#options SYSCTL_INCLUDE_DESCR # Include sysctl descriptions in kernel 77 78## NFS boot options; tries DHCP/BOOTP then BOOTPARAM 79options NFS_BOOT_BOOTPARAM 80#options NFS_BOOT_BOOTP 81options NFS_BOOT_DHCP 82 83#### Debugging options 84 85## The DDB in-kernel debugger runs at panic (unless DDB_ONPANIC=0), or at 86## serial console break or keyboard reset, where the PROM would normally 87## intercept. DDB_HISTORY_SIZE adds up/down arrow command history. 88#options DDB # kernel dynamic debugger 89#options DDB_HISTORY_SIZE=100 # enable history editing in DDB 90#options DDB_ONPANIC=1 # see also sysctl(7): `ddb.onpanic' 91 92## You may also use gdb, on another computer connected to this machine over 93## a serial port. Both KGDB_DEV and KGDB_DEVRATE should be specified; 94## KGDB_DEV is a dev_t encoded device number of the serial port to use. 95## (0xc01 = ttya, 0xc02 = ttyb.) 96#options KGDB # support for kernel gdb 97#options KGDB_DEV=0xc01 # kgdb device number (this is `ttyb') 98#options KGDB_DEVRATE=38400 # baud rate 99 100 101## Compile the kernel with debugging symbols (`netbsd.gdb' is the debug file), 102## such that gdb(1) can be used on a kernel coredump. 103 104#makeoptions DEBUG="-g" 105 106 107## Adds code to the kernel that does internal consistency checks, and will 108## cause the kernel to panic if corruption of internal data structures 109## is detected. 110#options DIAGNOSTIC # extra kernel sanity checking 111 112## Enable (possibly expensive) debugging code that may also display messages 113## on the system console 114#options DEBUG 115 116#options MIIVERBOSE # verbose PHY autoconfig messages 117 118## Make SCSI error messages more verbose when explaining their meanings. 119#options SCSIVERBOSE 120 121## `INSECURE' turns off the kernel security level (securelevel = 0 always). 122## This allows writing to /dev/mem, loading kernel modules while multi-user, 123## and other insecurities good only for development work. Do not use this 124## option on a production machine. 125options INSECURE 126 127## `FDSCRIPTS' allows non-readable but executable scripts by providing a 128## pre-opened opaque file to the script interpreter. `SETUIDSCRIPTS', 129## which implies FDSCRIPTS, allows scripts to be set-user-id using the same 130## opaque file mechanism. Perl calls this "secure setuid scripts." 131 132#options FDSCRIPTS 133#options SETUIDSCRIPTS 134 135## Options for compatibility with previous releases foreign system binaries. 136## In the cases of COMPAT_SUNOS, you may need to set up additional user-level 137## utilities or system configuration files. See compat_sunos(8). 138 139#include "conf/compat_netbsd10.config" 140#options COMPAT_SUNOS # SunOS 4.x binary compatibility 141options COMPAT_BSDPTY # /dev/[pt]ty?? ptys. 142 143## File systems. You probably need at least one of FFS or NFS. 144file-system FFS # Berkeley Fast Filesystem 145file-system NFS # Sun NFS-compatible filesystem client 146#file-system KERNFS # kernel data-structure filesystem 147#file-system NULLFS # NULL layered filesystem 148file-system MFS # memory-based filesystem 149#file-system FDESC # user file descriptor filesystem 150#file-system UMAPFS # uid/gid remapping filesystem 151#file-system LFS # Log-based filesystem (still experimental) 152#file-system PROCFS # /proc 153file-system CD9660 # ISO 9660 + Rock Ridge file system 154#file-system UNION # union file system 155#file-system MSDOSFS # MS-DOS FAT filesystem(s). 156#file-system PTYFS # /dev/pts/N support 157 158## File system options 159#options NFSSERVER # Sun NFS-compatible filesystem server 160#options QUOTA # legacy UFS quotas 161#options QUOTA2 # new, in-filesystem UFS quotas 162#options FFS_EI # FFS Endian Independent support 163#options NFS_V2_ONLY # Exclude NFS3 code to save space 164options FFS_NO_SNAPSHOT # No FFS snapshot support 165options WAPBL # File system journaling support 166 167## Network protocol support. In most environments, INET is required. 168options INET # IP (Internet Protocol) v4 169#options GATEWAY # packet forwarding ("router switch") 170#options MROUTING # packet forwarding of multicast packets 171#options PIM # Protocol Independent Multicast 172#options NETATALK # AppleTalk (over Ethernet) protocol 173#options NTP # Network Time Protocol in-kernel support 174#options PPS_SYNC # Add serial line synchronization for NTP 175#options PPP_BSDCOMP # Add BSD compression to ppp device 176#options PPP_DEFLATE # Add deflate (libz) compression to ppp device 177#options PPP_FILTER # Add active filters for ppp (via bpf) 178#options TCP_DEBUG # Record last TCP_NDEBUG packets with SO_DEBUG 179 180 181#### Main bus and CPU .. all systems. 182mainbus0 at root 183cpu0 at mainbus0 184 185#### SX rendering engine found in SS20 and SS10SX 186sx0 at mainbus0 187 188#### Bus types found on SPARC systems. 189 190sbus0 at mainbus0 # sun4c 191obio0 at mainbus0 # sun4 and sun4m 192sparcvme0 at mainbus0 # sun4 193iommu0 at mainbus0 # sun4m 194sbus0 at iommu0 # sun4m 195sparcvme0 at iommu0 # sun4m 196vme0 at sparcvme0 # mi VME attachment 197 198## SBus expander box 199xbox* at sbus? slot ? offset ? 200sbus* at xbox? 201 202## SBus to PCMCIA bridge 203# Currently enabling nell* with audioamd* causes panic at attach 204#nell* at sbus? slot ? offset ? # PCMCIA bridge 205#pcmcia* at nell? 206 207#### Standard system devices -- all required for a given architecture 208 209## Auxiliary system registers on sun4c and sun4m 210auxreg0 at mainbus0 # sun4c 211auxreg0 at obio0 # sun4m 212 213## Power status and control register on Sun4m systems 214power0 at obio0 215 216## Mostek clock found on 4/300, sun4c, and sun4m systems. 217## The Mostek clock NVRAM is the "eeprom" on sun4/300 systems. 218clock0 at mainbus0 # sun4c 219clock0 at obio0 # sun4m 220clock0 at obio0 addr 0xf2000000 # sun4/300 221 222## Intersil clock found on 4/100 and 4/200 systems. 223oclock0 at obio0 addr 0xf3000000 # sun4/200 224oclock0 at obio0 addr 0x03000000 # sun4/100 225 226## Memory error registers. 227memreg0 at mainbus0 # sun4c 228memreg0 at obio0 # sun4m 229memreg0 at obio0 addr 0xf4000000 # sun4/200 and sun4/300 230memreg0 at obio0 addr 0x04000000 # sun4/100 231 232## ECC memory control 233eccmemctl0 at mainbus0 # sun4m 234 235## Timer chip found on 4/300, sun4c, and sun4m systems. 236timer0 at mainbus0 # sun4c 237timer0 at obio0 # sun4m 238timer0 at obio0 addr 0xef000000 # sun4/300 239 240## EEPROM found on 4/100 and 4/200 systems. Note that the 4/300 241## doesn't use this driver; the `EEPROM' is in the NVRAM on the 242## Mostek clock chip on 4/300 systems. 243eeprom0 at obio0 addr 0xf2000000 # sun4/200 244eeprom0 at obio0 addr 0x02000000 # sun4/100 245 246 247#### Serial port configuration 248 249## Zilog 8530 serial chips. Each has two-channels. 250## zs0 is ttya and ttyb. zs1 is the keyboard and mouse. 251zs0 at mainbus0 # sun4c 252zs0 at obio0 # sun4m 253zs0 at obio0 addr 0xf1000000 level 12 flags 0x103 # sun4/200 and sun4/300 254zs0 at obio0 addr 0x01000000 level 12 flags 0x103 # sun4/100 255 256zs1 at mainbus0 # sun4c 257zs1 at obio0 # sun4m 258zs1 at obio0 addr 0xf0000000 level 12 flags 0x103 # sun4/200 and sun4/300 259zs1 at obio0 addr 0x00000000 level 12 flags 0x103 # sun4/100 260 261zs2 at obio0 addr 0xe0000000 level 12 # sun4/300 262 263zstty* at zs? 264 265# these are for wscons 266kbd0 at zstty? 267ms0 at zstty? 268wskbd* at wskbddev? 269wsmouse* at wsmousedev? 270 271## Magma Serial/Parallel driver 272#magma* at sbus? slot ? offset ? 273#mtty* at magma? 274#mbpp* at magma? 275 276## PCMCIA serial interfaces 277#com* at pcmcia? 278#pcmcom* at pcmcia? 279#com* at pcmcom? 280 281#### Disk controllers and disks 282 283# 284 285## The following flags may be set for the NCR53c94 based esp driver: 286## bits 0-7: disable disconnect/reselect for the corresponding target 287## bits 8-15: disable synchronous negotiation for target [bit-8] 288 289## sun4/300, sun4c, sun4m on-board SCSI, and FSBE/S SBus SCSI cards. 290## Both `dma' and `esp' are needed in all cases. 291## Two kinds of additional SBus SCSI interfaces are available. One uses 292## "esp at sbus" like the sun4c on-board; the other uses "esp at dma". 293 294## sun4/300 SCSI - an NCR53c94 or equivalent behind 295## an LSI Logic DMA controller 296 297dma0 at obio0 addr 0xfa001000 level 4 # sun4/300 298esp0 at obio0 addr 0xfa000000 level 4 flags 0x0000 # sun4/300 299 300dma0 at sbus0 slot ? offset ? # sun4c/sun4m 301esp0 at sbus0 slot ? offset ? flags 0x0000 # sun4c 302esp0 at dma0 flags 0x0000 # sun4m 303 304# FSBE/S SCSI 305dma* at sbus? slot ? offset ? # SBus 306esp* at sbus? slot ? offset ? flags 0x0000 # SBus (older proms) 307esp* at dma? flags 0x0000 # SBus 308 309scsibus* at esp? 310 311## Qlogic ISP SBus SCSI Card 312isp* at sbus? slot ? offset ? 313scsibus* at isp? 314 315## NCR5380-based "Sun SCSI 3" VME SCSI controller. 316## This driver has several flags which may be enabled by OR'ing 317## the values and using the "flags" directive. 318## Valid flags are: 319## 320## 0x01 Use DMA (may be polled) 321## 0x02 Use DMA completion interrupts 322## 0x04 Allow disconnect/reselect 323## 324## E.g. the following would enable DMA, interrupts, and reselect: 325## si0 at vme0 addr 0x200000 irq 3 vect 0x40 flags 0x07 326## 327## By default, DMA is enabled in the driver. 328 329si0 at vme0 addr 0x200000 irq 2 vect 0x40 330scsibus* at si? 331 332## NCR5380-based "SCSI Weird" on-board SCSI interface found 333## on sun4/100 systems. The flags are the same as the "si" 334## controller. Note, while DMA is enabled by default, only 335## polled DMA works at this time, and reselects do not work 336## on this particular controller. 337 338sw0 at obio0 addr 0x0a000000 level 3 339scsibus* at sw? 340 341## PCMCIA SCSI controllers 342#aic* at pcmcia? 343#scsibus* at aic? 344 345 346## These entries find devices on all SCSI busses and assign 347## unit numbers dynamically. 348sd* at scsibus? target ? lun ? # SCSI disks 349st* at scsibus? target ? lun ? # SCSI tapes 350cd* at scsibus? target ? lun ? # SCSI CD-ROMs 351#ch* at scsibus? target ? lun ? # SCSI changer devices 352#ss* at scsibus? target ? lun ? # SCSI scanners 353#uk* at scsibus? target ? lun ? # unknown SCSI 354 355 356## Xylogics 753 or 7053 VME SMD disk controllers and disks, found 357## on sun4 systems. 358xdc0 at vme0 addr 0xee80 irq 3 vect 0x44 359xdc1 at vme0 addr 0xee90 irq 3 vect 0x45 360xdc2 at vme0 addr 0xeea0 irq 3 vect 0x46 361xdc3 at vme0 addr 0xeeb0 irq 3 vect 0x47 362xd* at xdc? drive ? 363 364## Xylogics 451 or 451 VME SMD disk controllers and disks, found 365## on sun4 systems. 366xyc0 at vme0 addr 0xee40 irq 3 vect 0x48 367xyc1 at vme0 addr 0xee48 irq 3 vect 0x49 368xy* at xyc? drive ? 369 370 371## Floppy controller and drive found on SPARCstations. 372 373fdc0 at mainbus0 # sun4c controller 374fdc0 at obio0 # sun4m controller 375fd* at fdc0 # the drive itself 376 377## PCMCIA IDE controllers 378#wdc* at pcmcia? 379#wd* at wdc? 380 381## A disk-like interface to files. Can be used to create floppy, CD, 382## miniroot images, etc. 383 384#pseudo-device vnd 385 386## Concatenated and striped disks; with this, you can create a software-based 387## disk array similar to a "RAID 0" setup. See ccd(4). 388 389#pseudo-device ccd 390 391## RAIDframe disk driver: software RAID driver. See raid(4). 392 393#pseudo-device raid 394 395## Memory disk device, used on boot floppies with compressed 396## kernel-plus-root-disk images. 397 398#pseudo-device md 399 400 401#### Network interfaces 402 403## LANCE Ethernet - an AMD 7990 LANCE behind specialized DMA glue 404## Three flavors of additional SBus ethernets are available. One attaches 405## directly like the sun4c on-board, one uses the ledma device like the 406## sun4m on-board, and one uses the lebuffer device. 407 408le0 at obio0 addr 0xf9000000 level 6 # sun4/300 409le0 at sbus0 slot ? offset ? # sun4c on-board 410ledma0 at sbus0 slot ? offset ? # sun4m on-board 411le0 at ledma0 # sun4m on-board 412le* at sbus? slot ? offset ? # SBus 413ledma* at sbus? slot ? offset ? # SBus 414le* at ledma? # SBus 415lebuffer0 at sbus? slot ? offset ? # SBus 416le0 at lebuffer? # SBus 417lebuffer* at sbus? slot ? offset ? # SBus 418le* at lebuffer? # SBus 419 420 421## sun4/100 and sun4/200 Ethernet - an Intel 82586 on-board 422## or on a Multibus/VME card. 423ie0 at obio0 addr 0xf6000000 level 6 # sun4/200 on-board 424ie0 at obio0 addr 0x06000000 level 6 # sun4/100 on-board 425ie1 at vme0 addr 0xe88000 irq 3 vect 0x75 # VME 426ie2 at vme0 addr 0x31ff02 irq 3 vect 0x76 # VME 427ie3 at vme0 addr 0x35ff02 irq 3 vect 0x77 # VME 428ie4 at vme0 addr 0x2dff02 irq 3 vect 0x7c # VME 429 430## qec/be, qec/hme 431qec* at sbus? slot ? offset ? 432be* at qec? 433qe* at qec? 434 435# PCMCIA ethernet devices 436#ep* at pcmcia? 437#mbe* at pcmcia? 438#ne* at pcmcia? 439#sm* at pcmcia? 440 441# MII/PHY support 442#exphy* at mii? phy ? # 3Com internal PHYs 443#icsphy* at mii? phy ? # Integrated Circuit Systems ICS189x 444#inphy* at mii? phy ? # Intel 82555 PHYs 445#lxtphy* at mii? phy ? # Level One LXT-970 PHYs 446#nsphy* at mii? phy ? # NS83840 PHYs 447#qsphy* at mii? phy ? # Quality Semiconductor QS6612 PHYs 448#sqphy* at mii? phy ? # Seeq 80220/80221/80223 PHYs 449#tlphy* at mii? phy ? # ThunderLAN PHYs 450#ukphy* at mii? phy ? # generic unknown PHYs 451 452## Loopback network interface; required 453pseudo-device loop 454 455## SLIP and CSLIP interfaces, for IP over a serial line. 456#pseudo-device sl 457 458## PPP, the successor to SLIP. See pppd(8). 459#pseudo-device ppp 460 461## Network "tunnel" device, allowing protocol stacks to run in the userland. 462## This is used by the third-party user-mode "ppp" program, and others. 463#pseudo-device tun 464 465## Generic L3 over IP tunnel 466#pseudo-device gre # generic L3 over IP tunnel 467 468## Berkeley Packet Filter, required to run RARPD. A generic C-language 469## interface that allows selective examining of incoming packets. 470#pseudo-device bpfilter 471 472#pseudo-device npf # NPF packet filter 473 474#### Audio and video devices 475 476## /dev/audio support (`audioamd' plus `audio') 477## 478#audioamd0 at mainbus0 # sun4c 479#audioamd0 at obio0 # sun4m 480#audioamd0 at sbus0 slot ? offset ? # sun4m 481#audio* at audioamd0 482 483#audiocs0 at sbus0 slot ? offset ? # SUNW,CS4231 484#audio* at audiocs0 485 486#spkr* at audio? # PC speaker (synthesized) 487 488 489## Sun "bwtwo" black and white framebuffer, found on sun4, sun4c, and sun4m 490## systems. If your sun4 system has a cgfour installed in the P4 slot, 491## the P4 entries for "bwtwo" will attach to the overlay plane of the 492## "cgfour". 493 494bwtwo0 at sbus0 slot ? offset ? # sun4c and sun4m 495bwtwo* at sbus? slot ? offset ? # 496#bwtwo0 at obio0 addr 0xfd000000 level 4 # sun4/200 497#bwtwo0 at obio0 addr 0xfb300000 level 4 # sun4/300 in P4 slot 498#bwtwo0 at obio0 addr 0x0b300000 level 4 # sun4/100 in P4 slot 499 500## Sun "cgtwo" VME color framebuffer 501#cgtwo0 at vme0 addr 0x400000 irq ? vect 0xa8 502 503## Sun "cgthree" Sbus color framebuffer 504cgthree0 at sbus? slot ? offset ? 505cgthree* at sbus? slot ? offset ? 506 507## Sun "cgfour" color framebuffer with overlay plane. See above comment 508## regarding overlay plane. 509#cgfour0 at obio0 addr 0xfb300000 level 4 # sun4/300 P4 510#cgfour0 at obio0 addr 0x0b300000 level 4 # sun4/100 P4 511 512## Sun "cgsix" accelerated color framebuffer. 513cgsix0 at sbus? slot ? offset ? 514cgsix* at sbus? slot ? offset ? 515#cgsix0 at obio0 addr 0xfb000000 level 4 # sun4/300 P4 516#cgsix0 at obio0 addr 0x0b000000 level 4 # sun4/100 P4 517 518## Sun "cgeight" 24-bit framebuffer 519#cgeight0 at obio0 addr 0xfb300000 level 4 # sun4/300 P4 520#cgeight0 at obio0 addr 0x0b300000 level 4 # sun4/100 P4 521 522## Sun "tcx" accelerated color framebuffer. 523# there can be only one 524tcx0 at sbus? slot ? offset ? 525 526## Sun CG12 / Matrox SG3 accelerated 24bit framebuffer 527## runs monochrome only for now 528## since it occupies 3 SBus slots there's no way to use more than one 529cgtwelve0 at sbus? slot ? offset ? 530 531# Sun "cgfourteen" accelerated 24-bit framebuffer. 532cgfourteen* at obio0 # sun4m 533 534# P9100-based display on Tadpole SPARCbook 3. 535pnozz0 at sbus? slot ? offset ? 536# the SPARCbook 3 hardware docs say that accesses to P9100 registers need to be 537# 'latched in' but at least my 3GX works happily without 538# Enable it by default since we don't know which hardware really needs it. 539options PNOZZ_USE_LATCH 540 541# Sun ZX/Leo 24-bit framebuffer 542zx* at sbus? slot ? offset ? 543 544# Fujitsu AG-10e accelerated graphics 8/24-bit board 545agten* at sbus? slot ? offset ? 546 547## Southland Media Systems (now Quantum 3D) MGX 548mgx* at sbus? slot ? offset ? 549 550# generic framebuffer console 551genfb* at sbus? slot ? offset ? 552 553# make sure wsdisplay0 is the console 554wsdisplay0 at wsemuldisplaydev? console 1 555wsdisplay* at wsemuldisplaydev? 556 557#### Other device configuration 558 559## Pseudo ttys, required for network logins and programs like screen. 560 561pseudo-device pty # pseudo-terminals 562 563## Random device, used to implement /dev/random (a source of random noise), 564## and generate randomness for some kernel formulae. 565 566#pseudo-device fss # file system snapshot device 567 568pseudo-device wsmux # mouse and keyboard multiplexor 569pseudo-device wsfont 570