INSTALL revision 1.28
1# $NetBSD: INSTALL,v 1.28 2001/11/20 12:56:39 lukem Exp $ 2# 3# from: NetBSD: GENERIC,v 1.84 1999/06/06 13:00:03 mrg Exp 4# 5# floppy install kernel. try to keep this in sync with GENERIC but 6# leave as much disabled as possible. 7 8include "arch/sparc/conf/std.sparc" 9 10makeoptions COPTS="-Os" # Optimise for space. Implies -O2 11 12maxusers 32 13 14# Enable the hooks used for initializing the root memory-disk. 15options MEMORY_DISK_HOOKS 16options MEMORY_DISK_IS_ROOT # force root on memory disk 17options MEMORY_DISK_SERVER=0 # no userspace memory disk support 18## The miniroot size must be kept in sync manually with the size of 19## the `ramdisk' image (which is built in distrib/sparc/ramdisk). 20options MINIROOTSIZE=1360 # size of memory disk, in blocks 21 22pseudo-device md 1 # memory disk device (ramdisk) 23 24## System kernel configuration. See options(4) for more detail. 25 26 27# Options for variants of the Sun SPARC architecure. 28# We currently support three architecture types; at least one is required. 29options SUN4 # sun4/100, sun4/200, sun4/300 30options SUN4C # sun4c - SS1, 1+, 2, ELC, SLC, IPC, IPX, etc. 31options SUN4M # sun4m - SS10, SS20, Classic, etc. 32 33options SUN4_MMU3L # 3-level MMU on sun4/400 34 35## System options specific to the sparc machine type 36 37# Blink the power LED on some machines to indicate the system load. 38#options BLINK 39 40## Use a faster console than the PROM's slow drawing routines. Not needed 41## for headless (no framebuffer) machines. 42#options RASTERCONSOLE # fast rasterop console 43#options FONT_GALLANT12x22 # the console font 44#options FONT_BOLD8x16 # a somewhat smaller font 45#options RASTERCONSOLE_FGCOL=WSCOL_BLACK 46#options RASTERCONSOLE_BGCOL=WSCOL_WHITE 47 48#### System options that are the same for all ports 49 50## Root device configuration: change the ?'s if you are going to use a 51## nonstandard root partition (other than where the kernel is booted from) 52## and/or nonstandard root type (not ffs or nfs). Normally this can be 53## automagically determined at boot time. 54 55config netbsd root on ? type ? 56 57## System call tracing (see ktrace(1)). 58#options KTRACE 59 60## Collect statistics on kernel malloc's and free's. This does have a 61## significant performance hit on slower machines, so it is intended for 62## diagnostic use only. 63#options KMEMSTATS 64 65## System V compatible IPC subsystem. (msgctl(2), semctl(2), and shmctl(2)) 66#options SYSVMSG # System V message queues 67#options SYSVSEM # System V semaphores 68#options SYSVSHM # System V shared memory 69#options SHMMAXPGS=1024 # 1024 pages is the default 70 71## Loadable kernel module support; still under development. 72#options LKM 73 74## NFS boot options; default on sparc is the bootparam protocol 75options NFS_BOOT_BOOTPARAM 76#options NFS_BOOT_BOOTP 77#options NFS_BOOT_DHCP 78 79#### Debugging options 80 81## The DDB in-kernel debugger runs at panic (unless DDB_ONPANIC=0), or at 82## serial console break or keyboard reset, where the PROM would normally 83## intercept. DDB_HISTORY_SIZE adds up/down arrow command history. 84#options DDB # kernel dynamic debugger 85#options DDB_HISTORY_SIZE=100 # enable history editing in DDB 86#options DDB_ONPANIC=1 # see also sysctl(8): `ddb.onpanic' 87 88## You may also use gdb, on another computer connected to this machine over 89## a serial port. Both KGDB_DEV and KGDB_DEVRATE should be specified; 90## KGDB_DEV is a dev_t encoded device number of the serial port to use. 91## (0xc01 = ttya, 0xc02 = ttyb.) 92#options KGDB # support for kernel gdb 93#options KGDB_DEV=0xc01 # kgdb device number (this is `ttyb') 94#options KGDB_DEVRATE=38400 # baud rate 95 96 97## Compile the kernel with debugging symbols (`netbsd.gdb' is the debug file), 98## such that gdb(1) can be used on a kernel coredump. 99 100#makeoptions DEBUG="-g" 101 102 103## Adds code to the kernel that does internal consistency checks, and will 104## cause the kernel to panic if corruption of internal data structures 105## is detected. 106#options DIAGNOSTIC # extra kernel sanity checking 107 108## Enable (possibly expensive) debugging code that may also display messages 109## on the system console 110#options DEBUG 111 112#options MIIVERBOSE # verbose PHY autoconfig messages 113 114## Make SCSI error messages more verbose when explaining their meanings. 115#options SCSIVERBOSE 116 117## `INSECURE' turns off the kernel security level (securelevel = 0 always). 118## This allows writing to /dev/mem, loading kernel modules while multi-user, 119## and other insecurities good only for development work. Do not use this 120## option on a production machine. 121options INSECURE 122 123## Allow non-root users to grab /dev/console with programs such as xconsole. 124## `xconsole' therefore does not need setuid root with this option enabled. 125#options UCONSOLE 126 127## `FDSCRIPTS' allows non-readable but executable scripts by providing a 128## pre-opened opaque file to the script interpreter. `SETUIDSCRIPTS', 129## which implies FDSCRIPTS, allows scripts to be set-user-id using the same 130## opaque file mechanism. Perl calls this "secure setuid scripts." 131 132#options FDSCRIPTS 133#options SETUIDSCRIPTS 134 135## Options for compatibility with previous releases foreign system binaries. 136## In the cases of COMPAT_SUNOS and COMPAT_SVR4, you may need to set up 137## additional user-level utilities or system configuration files. See 138## compat_sunos(8) and compat_svr4(8). 139 140#options COMPAT_43 # 4.3BSD system interfaces 141#options COMPAT_10 # NetBSD 1.0 binary compatibility 142#options COMPAT_11 # NetBSD 1.1 binary compatibility 143#options COMPAT_12 # NetBSD 1.2 binary compatibility 144#options COMPAT_13 # NetBSD 1.3 binary compatibility 145#options COMPAT_14 # NetBSD 1.4 binary compatibility 146#options COMPAT_SUNOS # SunOS 4.x binary compatibility 147#options COMPAT_SVR4 # SunOS 5.x binary compatibility 148#options TCP_COMPAT_42 # 4.2BSD TCP/IP bug compat. Not recommended. 149 150## File systems. You probably need at least one of FFS or NFS. 151file-system FFS # Berkeley Fast Filesystem 152file-system NFS # Sun NFS-compatible filesystem client 153#file-system KERNFS # kernel data-structure filesystem 154#file-system NULLFS # NULL layered filesystem 155file-system MFS # memory-based filesystem 156#file-system FDESC # user file descriptor filesystem 157#file-system UMAPFS # uid/gid remapping filesystem 158#file-system LFS # Log-based filesystem (still experimental) 159#file-system PORTAL # portal filesystem (still experimental) 160#file-system PROCFS # /proc 161file-system CD9660 # ISO 9660 + Rock Ridge file system 162#file-system UNION # union file system 163#file-system MSDOSFS # MS-DOS FAT filesystem(s). 164 165## File system options 166#options NFSSERVER # Sun NFS-compatible filesystem server 167#options QUOTA # FFS quotas 168#options FFS_EI # FFS Endian Independent support 169#options NFS_V2_ONLY # Exclude NFS3 and NQNFS code to save space 170#options VNODE_OP_NOINLINE # Save space by not inlining vnode op calls 171 172## Network protocol support. In most environments, INET is required. 173options INET # IP (Internet Protocol) v4 174#options GATEWAY # packet forwarding ("router switch") 175#options MROUTING # packet forwarding of multicast packets 176#options DIRECTED_BROADCAST # allow broadcasts through routers 177#options NS # Xerox NS networking 178#options NSIP # Xerox NS tunneling over IP 179#options ISO,TPIP # OSI networking 180#options EON # OSI tunneling over IP 181#options CCITT,LLC,HDLC # X.25 packet switched protocol 182#options NETATALK # AppleTalk (over Ethernet) protocol 183#options NTP # Network Time Protocol in-kernel support 184#options PPS_SYNC # Add serial line synchronization for NTP 185#options PFIL_HOOKS # Add pfil(9) hooks, intended for custom LKMs. 186#options IPFILTER_LOG # Add ipmon(8) logging for ipfilter device 187#options PPP_BSDCOMP # Add BSD compression to ppp device 188#options PPP_DEFLATE # Add deflate (libz) compression to ppp device 189#options PPP_FILTER # Add active filters for ppp (via bpf) 190#options TCP_DEBUG # Record last TCP_NDEBUG packets with SO_DEBUG 191 192 193#### Main bus and CPU .. all systems. 194mainbus0 at root 195cpu0 at mainbus0 196 197#### Bus types found on SPARC systems. 198 199sbus0 at mainbus0 # sun4c 200obio0 at mainbus0 # sun4 and sun4m 201sparcvme0 at mainbus0 # sun4 202iommu0 at mainbus0 # sun4m 203sbus0 at iommu0 # sun4m 204sparcvme0 at iommu0 # sun4m 205vme0 at sparcvme0 # mi VME attachment 206 207## SBus expander box 208xbox* at sbus? slot ? offset ? 209sbus* at xbox? 210 211## SBus to PCMCIA bridge 212# Currently enabling nell* with audioamd* causes panic at attach 213#nell* at sbus? slot ? offset ? # PCMCIA bridge 214#pcmcia* at nell? 215 216#### Standard system devices -- all required for a given architecture 217 218## Auxiliary system registers on sun4c and sun4m 219auxreg0 at mainbus0 # sun4c 220auxreg0 at obio0 # sun4m 221 222## Power status and control register on Sun4m systems 223power0 at obio0 224 225## Mostek clock found on 4/300, sun4c, and sun4m systems. 226## The Mostek clock NVRAM is the "eeprom" on sun4/300 systems. 227clock0 at mainbus0 # sun4c 228clock0 at obio0 # sun4m 229clock0 at obio0 addr 0xf2000000 # sun4/300 230 231## Intersil clock found on 4/100 and 4/200 systems. 232oclock0 at obio0 addr 0xf3000000 # sun4/200 233oclock0 at obio0 addr 0x03000000 # sun4/100 234 235## Memory error registers. 236memreg0 at mainbus0 # sun4c 237memreg0 at obio0 # sun4m 238memreg0 at obio0 addr 0xf4000000 # sun4/200 and sun4/300 239memreg0 at obio0 addr 0x04000000 # sun4/100 240 241## ECC memory control 242eccmemctl0 at mainbus0 # sun4m 243 244## Timer chip found on 4/300, sun4c, and sun4m systems. 245timer0 at mainbus0 # sun4c 246timer0 at obio0 # sun4m 247timer0 at obio0 addr 0xef000000 # sun4/300 248 249## EEPROM found on 4/100 and 4/200 systems. Note that the 4/300 250## doesn't use this driver; the `EEPROM' is in the NVRAM on the 251## Mostek clock chip on 4/300 systems. 252eeprom0 at obio0 addr 0xf2000000 # sun4/200 253eeprom0 at obio0 addr 0x02000000 # sun4/100 254 255 256#### Serial port configuration 257 258## Zilog 8530 serial chips. Each has two-channels. 259## zs0 is ttya and ttyb. zs1 is the keyboard and mouse. 260zs0 at mainbus0 # sun4c 261zs0 at obio0 # sun4m 262zs0 at obio0 addr 0xf1000000 level 12 flags 0x103 # sun4/200 and sun4/300 263zs0 at obio0 addr 0x01000000 level 12 flags 0x103 # sun4/100 264zstty0 at zs0 channel 0 # ttya 265zstty1 at zs0 channel 1 # ttyb 266 267zs1 at mainbus0 # sun4c 268zs1 at obio0 # sun4m 269zs1 at obio0 addr 0xf0000000 level 12 flags 0x103 # sun4/200 and sun4/300 270zs1 at obio0 addr 0x00000000 level 12 flags 0x103 # sun4/100 271kbd0 at zs1 channel 0 # keyboard 272ms0 at zs1 channel 1 # mouse 273 274zs2 at obio0 addr 0xe0000000 level 12 flags 0x103 # sun4/300 275zstty2 at zs2 channel 0 # ttyc 276zstty3 at zs2 channel 1 # ttyd 277 278 279## Magma Serial/Parallel driver 280#magma* at sbus? slot ? offset ? 281#mtty* at magma? 282#mbpp* at magma? 283 284## PCMCIA serial interfaces 285#com* at pcmcia? 286#pcmcom* at pcmcia? 287#com* at pcmcom? 288 289#### Disk controllers and disks 290 291# 292 293## The following flags may be set for the NCR53c94 based esp driver: 294## bits 0-7: disable disconnect/reselect for the corresponding target 295## bits 8-15: disable synchronous negotiation for target [bit-8] 296 297## sun4/300, sun4c, sun4m on-board SCSI, and FSBE/S SBus SCSI cards. 298## Both `dma' and `esp' are needed in all cases. 299## Two kinds of additional SBus SCSI interfaces are available. One uses 300## "esp at sbus" like the sun4c on-board; the other uses "esp at dma". 301 302## sun4/300 SCSI - an NCR53c94 or equivalent behind 303## an LSI Logic DMA controller 304 305dma0 at obio0 addr 0xfa001000 level 4 # sun4/300 306esp0 at obio0 addr 0xfa000000 level 4 flags 0x0000 # sun4/300 307 308dma0 at sbus0 slot ? offset ? # sun4c/sun4m 309esp0 at sbus0 slot ? offset ? flags 0x0000 # sun4c 310esp0 at dma0 flags 0x0000 # sun4m 311 312# FSBE/S SCSI 313dma* at sbus? slot ? offset ? # SBus 314esp* at sbus? slot ? offset ? flags 0x0000 # SBus (older proms) 315esp* at dma? flags 0x0000 # SBus 316 317scsibus* at esp? 318 319## Qlogic ISP SBus SCSI Card 320isp* at sbus? slot ? offset ? 321scsibus* at isp? 322 323## NCR5380-based "Sun SCSI 3" VME SCSI controller. 324## This driver has several flags which may be enabled by OR'ing 325## the values and using the "flags" directive. 326## Valid flags are: 327## 328## 0x01 Use DMA (may be polled) 329## 0x02 Use DMA completion interrupts 330## 0x04 Allow disconnect/reselect 331## 332## E.g. the following would enable DMA, interrupts, and reselect: 333## si0 at vme0 addr 0x200000 irq 3 vect 0x40 flags 0x07 334## 335## By default, DMA is enabled in the driver. 336 337si0 at vme0 addr 0x200000 irq 2 vect 0x40 338scsibus* at si? 339 340## NCR5380-based "SCSI Weird" on-board SCSI interface found 341## on sun4/100 systems. The flags are the same as the "si" 342## controller. Note, while DMA is enabled by default, only 343## polled DMA works at this time, and reselects do not work 344## on this particular controller. 345 346sw0 at obio0 addr 0x0a000000 level 3 347scsibus* at sw? 348 349## PCMCIA SCSI controllers 350#aic* at pcmcia? 351#scsibus* at aic? 352 353 354## These entries find devices on all SCSI busses and assign 355## unit numbers dynamically. 356sd* at scsibus? target ? lun ? # SCSI disks 357st* at scsibus? target ? lun ? # SCSI tapes 358cd* at scsibus? target ? lun ? # SCSI CD-ROMs 359#ch* at scsibus? target ? lun ? # SCSI changer devices 360#ss* at scsibus? target ? lun ? # SCSI scanners 361#uk* at scsibus? target ? lun ? # unknown SCSI 362 363 364## Xylogics 753 or 7053 VME SMD disk controllers and disks, found 365## on sun4 systems. 366xdc0 at vme0 addr 0xee80 irq 3 vect 0x44 367xdc1 at vme0 addr 0xee90 irq 3 vect 0x45 368xdc2 at vme0 addr 0xeea0 irq 3 vect 0x46 369xdc3 at vme0 addr 0xeeb0 irq 3 vect 0x47 370xd* at xdc? drive ? 371 372## Xylogics 451 or 451 VME SMD disk controllers and disks, found 373## on sun4 systems. 374xyc0 at vme0 addr 0xee40 irq 3 vect 0x48 375xyc1 at vme0 addr 0xee48 irq 3 vect 0x49 376xy* at xyc? drive ? 377 378 379## Floppy controller and drive found on SPARCstations. 380 381fdc0 at mainbus0 # sun4c controller 382fdc0 at obio0 # sun4m controller 383fd* at fdc0 # the drive itself 384 385## PCMCIA IDE controllers 386#wdc* at pcmcia? 387#wd* at wdc? 388 389## A disk-like interface to files. Can be used to create floppy, CD, 390## miniroot images, etc. 391 392#pseudo-device vnd 4 393 394## Concatenated and striped disks; with this, you can create a software-based 395## disk array similar to a "RAID 0" setup. See ccd(4). 396 397#pseudo-device ccd 4 398 399## RAIDframe disk driver: software RAID driver. See raid(4). 400 401#pseudo-device raid 4 402 403## Memory disk device, used on boot floppies with compressed 404## kernel-plus-root-disk images. 405 406#pseudo-device md 1 407 408 409#### Network interfaces 410 411## LANCE Ethernet - an AMD 7990 LANCE behind specialized DMA glue 412## Three flavors of additional SBus ethernets are available. One attaches 413## directly like the sun4c on-board, one uses the ledma device like the 414## sun4m on-board, and one uses the lebuffer device. 415 416le0 at obio0 addr 0xf9000000 level 6 # sun4/300 417le0 at sbus0 slot ? offset ? # sun4c on-board 418ledma0 at sbus0 slot ? offset ? # sun4m on-board 419le0 at ledma0 # sun4m on-board 420le* at sbus? slot ? offset ? # SBus 421ledma* at sbus? slot ? offset ? # SBus 422le* at ledma? # SBus 423lebuffer0 at sbus? slot ? offset ? # SBus 424le0 at lebuffer? # SBus 425lebuffer* at sbus? slot ? offset ? # SBus 426le* at lebuffer? # SBus 427 428 429## sun4/100 and sun4/200 Ethernet - an Intel 82586 on-board 430## or on a Multibus/VME card. 431ie0 at obio0 addr 0xf6000000 level 6 # sun4/200 on-board 432ie0 at obio0 addr 0x06000000 level 6 # sun4/100 on-board 433ie1 at vme0 addr 0xe88000 irq 3 vect 0x75 # VME 434ie2 at vme0 addr 0x31ff02 irq 3 vect 0x76 # VME 435ie3 at vme0 addr 0x35ff02 irq 3 vect 0x77 # VME 436ie4 at vme0 addr 0x2dff02 irq 3 vect 0x7c # VME 437 438## qec/be, qec/hme 439qec* at sbus? slot ? offset ? 440be* at qec? 441qe* at qec? 442 443# midway ATM 444en0 at sbus? slot ? offset ? 445 446# PCMCIA ethernet devices 447#ep* at pcmcia? 448#mbe* at pcmcia? 449#ne* at pcmcia? 450#sm* at pcmcia? 451 452# MII/PHY support 453#exphy* at mii? phy ? # 3Com internal PHYs 454#icsphy* at mii? phy ? # Integrated Circuit Systems ICS1890 455#inphy* at mii? phy ? # Intel 82555 PHYs 456#lxtphy* at mii? phy ? # Level One LXT-970 PHYs 457#nsphy* at mii? phy ? # NS83840 PHYs 458#qsphy* at mii? phy ? # Quality Semiconductor QS6612 PHYs 459#sqphy* at mii? phy ? # Seeq 80220/80221/80223 PHYs 460#tlphy* at mii? phy ? # ThunderLAN PHYs 461#ukphy* at mii? phy ? # generic unknown PHYs 462 463## Loopback network interface; required 464pseudo-device loop 465 466## SLIP and CSLIP interfaces, for IP over a serial line. 467#pseudo-device sl 2 468 469## PPP, the successor to SLIP. See pppd(8). 470#pseudo-device ppp 2 471 472## Starmode Radio IP, a special hardware network device. 473#pseudo-device strip 1 474 475## Network "tunnel" device, allowing protocol stacks to run in the userland. 476## This is used by the third-party user-mode "ppp" program, and others. 477#pseudo-device tun 4 478 479## Generic L3 over IP tunnel 480#pseudo-device gre 2 # generic L3 over IP tunnel 481 482## Berkeley Packet Filter, required to run RARPD. A generic C-language 483## interface that allows selective examining of incoming packets. 484#pseudo-device bpfilter 8 485 486## IP Filter, used in firewall and NAT applications. See ipnat(8) for 487## one example of the use of the IP Filter. 488#pseudo-device ipfilter 489 490 491#### Audio and video devices 492 493## /dev/audio support (`audioamd' plus `audio') 494## 495#audioamd0 at mainbus0 # sun4c 496#audioamd0 at obio0 # sun4m 497#audioamd0 at sbus0 slot ? offset ? # sun4m 498#audio* at audioamd0 499 500#audiocs0 at sbus0 slot ? offset ? # SUNW,CS4231 501#audio* at audiocs0 502 503 504## Sun "bwtwo" black and white framebuffer, found on sun4, sun4c, and sun4m 505## systems. If your sun4 system has a cgfour installed in the P4 slot, 506## the P4 entries for "bwtwo" will attach to the overlay plane of the 507## "cgfour". 508 509bwtwo0 at sbus0 slot ? offset ? # sun4c and sun4m 510bwtwo* at sbus? slot ? offset ? # 511#bwtwo0 at obio0 addr 0xfd000000 level 4 # sun4/200 512#bwtwo0 at obio0 addr 0xfb300000 level 4 # sun4/300 in P4 slot 513#bwtwo0 at obio0 addr 0x0b300000 level 4 # sun4/100 in P4 slot 514 515## Sun "cgtwo" VME color framebuffer 516#cgtwo0 at vme0 addr 0x400000 irq ? vect 0xa8 517 518## Sun "cgthree" Sbus color framebuffer 519cgthree0 at sbus? slot ? offset ? 520cgthree* at sbus? slot ? offset ? 521#cgthree0 at obio? slot ? offset ? # sun4m 522 523## Sun "cgfour" color framebuffer with overlay plane. See above comment 524## regarding overlay plane. 525#cgfour0 at obio0 addr 0xfb300000 level 4 # sun4/300 P4 526#cgfour0 at obio0 addr 0x0b300000 level 4 # sun4/100 P4 527 528## Sun "cgsix" accelerated color framebuffer. 529cgsix0 at sbus? slot ? offset ? 530cgsix* at sbus? slot ? offset ? 531#cgsix0 at obio0 addr 0xfb000000 level 4 # sun4/300 P4 532#cgsix0 at obio0 addr 0x0b000000 level 4 # sun4/100 P4 533 534## Sun "cgeight" 24-bit framebuffer 535#cgeight0 at obio0 addr 0xfb300000 level 4 # sun4/300 P4 536#cgeight0 at obio0 addr 0x0b300000 level 4 # sun4/100 P4 537 538## Sun "tcx" accelerated color framebuffer. 539tcx0 at sbus? slot ? offset ? 540tcx* at sbus? slot ? offset ? 541 542# Sun "cgfourteen" accelerated 24-bit framebuffer. 543cgfourteen0 at obio0 # sun4m 544 545 546#### Other device configuration 547 548## Pseudo ttys, required for network logins and programs like screen. 549 550pseudo-device pty 2 # pseudo-terminals (Sysinst needs two) 551 552## Random device, used to implement /dev/random (a source of random noise), 553## and generate randomness for some kernel formulae. 554 555#pseudo-device rnd 556