INSTALL revision 1.42
1# $NetBSD: INSTALL,v 1.42 2004/07/15 03:53:52 atatat Exp $ 2# 3# from: NetBSD: GENERIC,v 1.84 1999/06/06 13:00:03 mrg Exp 4# 5# floppy install kernel. try to keep this in sync with GENERIC but 6# leave as much disabled as possible. 7 8include "arch/sparc/conf/std.sparc" 9 10#options INCLUDE_CONFIG_FILE # embed config file in kernel binary 11 12makeoptions COPTS="-Os" # Optimise for space. Implies -O2 13 14maxusers 32 15 16# Enable the hooks used for initializing the root memory-disk. 17options MEMORY_DISK_HOOKS 18options MEMORY_DISK_IS_ROOT # force root on memory disk 19options MEMORY_DISK_SERVER=0 # no userspace memory disk support 20## The miniroot size must be kept in sync manually with the size of 21## the `ramdisk' image (which is built in distrib/sparc/ramdisk). 22options MEMORY_DISK_ROOT_SIZE=1376 # size of memory disk, in blocks 23 24pseudo-device md 1 # memory disk device (ramdisk) 25 26## System kernel configuration. See options(4) for more detail. 27 28 29# Options for variants of the Sun SPARC architecure. 30# We currently support three architecture types; at least one is required. 31options SUN4 # sun4/100, sun4/200, sun4/300 32options SUN4C # sun4c - SS1, 1+, 2, ELC, SLC, IPC, IPX, etc. 33options SUN4M # sun4m - SS10, SS20, Classic, etc. 34 35options SUN4_MMU3L # 3-level MMU on sun4/400 36 37## System options specific to the sparc machine type 38 39# Blink the power LED on some machines to indicate the system load. 40#options BLINK 41 42## Use a faster console than the PROM's slow drawing routines. Not needed 43## for headless (no framebuffer) machines. 44#options RASTERCONSOLE # fast rasterop console 45#options FONT_GALLANT12x22 # the console font 46#options FONT_BOLD8x16 # a somewhat smaller font 47#options RASTERCONSOLE_FGCOL=WSCOL_BLACK 48#options RASTERCONSOLE_BGCOL=WSCOL_WHITE 49 50#### System options that are the same for all ports 51 52## Root device configuration: change the ?'s if you are going to use a 53## nonstandard root partition (other than where the kernel is booted from) 54## and/or nonstandard root type (not ffs or nfs). Normally this can be 55## automagically determined at boot time. 56 57config netbsd root on ? type ? 58 59## System call tracing (see ktrace(1)). 60#options KTRACE 61 62## Collect statistics on kernel malloc's and free's. This does have a 63## significant performance hit on slower machines, so it is intended for 64## diagnostic use only. 65#options KMEMSTATS 66 67## System V compatible IPC subsystem. (msgctl(2), semctl(2), and shmctl(2)) 68#options SYSVMSG # System V message queues 69#options SYSVSEM # System V semaphores 70#options SYSVSHM # System V shared memory 71#options SHMMAXPGS=1024 # 1024 pages is the default 72 73## Loadable kernel module support; still under development. 74#options LKM 75 76options USERCONF # userconf(4) support 77options PIPE_SOCKETPAIR # smaller, but slower pipe(2) 78#options SYSCTL_INCLUDE_DESCR # Include sysctl descriptions in kernel 79options MALLOC_NOINLINE # Not inlining MALLOC saves memory 80 81## NFS boot options; tries DHCP/BOOTP then BOOTPARAM 82options NFS_BOOT_BOOTPARAM 83#options NFS_BOOT_BOOTP 84options NFS_BOOT_DHCP 85 86#### Debugging options 87 88## The DDB in-kernel debugger runs at panic (unless DDB_ONPANIC=0), or at 89## serial console break or keyboard reset, where the PROM would normally 90## intercept. DDB_HISTORY_SIZE adds up/down arrow command history. 91#options DDB # kernel dynamic debugger 92#options DDB_HISTORY_SIZE=100 # enable history editing in DDB 93#options DDB_ONPANIC=1 # see also sysctl(8): `ddb.onpanic' 94 95## You may also use gdb, on another computer connected to this machine over 96## a serial port. Both KGDB_DEV and KGDB_DEVRATE should be specified; 97## KGDB_DEV is a dev_t encoded device number of the serial port to use. 98## (0xc01 = ttya, 0xc02 = ttyb.) 99#options KGDB # support for kernel gdb 100#options KGDB_DEV=0xc01 # kgdb device number (this is `ttyb') 101#options KGDB_DEVRATE=38400 # baud rate 102 103 104## Compile the kernel with debugging symbols (`netbsd.gdb' is the debug file), 105## such that gdb(1) can be used on a kernel coredump. 106 107#makeoptions DEBUG="-g" 108 109 110## Adds code to the kernel that does internal consistency checks, and will 111## cause the kernel to panic if corruption of internal data structures 112## is detected. 113#options DIAGNOSTIC # extra kernel sanity checking 114 115## Enable (possibly expensive) debugging code that may also display messages 116## on the system console 117#options DEBUG 118 119#options MIIVERBOSE # verbose PHY autoconfig messages 120 121## Make SCSI error messages more verbose when explaining their meanings. 122#options SCSIVERBOSE 123 124## `INSECURE' turns off the kernel security level (securelevel = 0 always). 125## This allows writing to /dev/mem, loading kernel modules while multi-user, 126## and other insecurities good only for development work. Do not use this 127## option on a production machine. 128options INSECURE 129 130## `FDSCRIPTS' allows non-readable but executable scripts by providing a 131## pre-opened opaque file to the script interpreter. `SETUIDSCRIPTS', 132## which implies FDSCRIPTS, allows scripts to be set-user-id using the same 133## opaque file mechanism. Perl calls this "secure setuid scripts." 134 135#options FDSCRIPTS 136#options SETUIDSCRIPTS 137 138## Options for compatibility with previous releases foreign system binaries. 139## In the cases of COMPAT_SUNOS and COMPAT_SVR4, you may need to set up 140## additional user-level utilities or system configuration files. See 141## compat_sunos(8) and compat_svr4(8). 142 143#options COMPAT_43 # 4.3BSD system interfaces 144#options COMPAT_10 # NetBSD 1.0 binary compatibility 145#options COMPAT_11 # NetBSD 1.1 binary compatibility 146#options COMPAT_12 # NetBSD 1.2 binary compatibility 147#options COMPAT_13 # NetBSD 1.3 binary compatibility 148#options COMPAT_14 # NetBSD 1.4 binary compatibility 149#options COMPAT_16 # NetBSD 1.6 binary compatibility 150#options COMPAT_SUNOS # SunOS 4.x binary compatibility 151#options COMPAT_SVR4 # SunOS 5.x binary compatibility 152#options TCP_COMPAT_42 # 4.2BSD TCP/IP bug compat. Not recommended. 153 154## File systems. You probably need at least one of FFS or NFS. 155file-system FFS # Berkeley Fast Filesystem 156file-system NFS # Sun NFS-compatible filesystem client 157#file-system KERNFS # kernel data-structure filesystem 158#file-system NULLFS # NULL layered filesystem 159file-system MFS # memory-based filesystem 160#file-system FDESC # user file descriptor filesystem 161#file-system UMAPFS # uid/gid remapping filesystem 162#file-system LFS # Log-based filesystem (still experimental) 163#file-system PORTAL # portal filesystem (still experimental) 164#file-system PROCFS # /proc 165file-system CD9660 # ISO 9660 + Rock Ridge file system 166#file-system UNION # union file system 167#file-system MSDOSFS # MS-DOS FAT filesystem(s). 168 169## File system options 170#options NFSSERVER # Sun NFS-compatible filesystem server 171#options QUOTA # FFS quotas 172#options FFS_EI # FFS Endian Independent support 173#options NFS_V2_ONLY # Exclude NFS3 and NQNFS code to save space 174options VNODE_OP_NOINLINE # Not inlining vnode op calls saves mem 175 176## Network protocol support. In most environments, INET is required. 177options INET # IP (Internet Protocol) v4 178#options GATEWAY # packet forwarding ("router switch") 179#options MROUTING # packet forwarding of multicast packets 180#options DIRECTED_BROADCAST # allow broadcasts through routers 181#options NS # Xerox NS networking 182#options NSIP # Xerox NS tunneling over IP 183#options ISO,TPIP # OSI networking 184#options EON # OSI tunneling over IP 185#options CCITT,LLC,HDLC # X.25 packet switched protocol 186#options NETATALK # AppleTalk (over Ethernet) protocol 187#options NTP # Network Time Protocol in-kernel support 188#options PPS_SYNC # Add serial line synchronization for NTP 189#options PFIL_HOOKS # Add pfil(9) hooks, intended for custom LKMs. 190#options IPFILTER_LOG # Add ipmon(8) logging for ipfilter device 191#options PPP_BSDCOMP # Add BSD compression to ppp device 192#options PPP_DEFLATE # Add deflate (libz) compression to ppp device 193#options PPP_FILTER # Add active filters for ppp (via bpf) 194#options TCP_DEBUG # Record last TCP_NDEBUG packets with SO_DEBUG 195 196 197#### Main bus and CPU .. all systems. 198mainbus0 at root 199cpu0 at mainbus0 200 201#### Bus types found on SPARC systems. 202 203sbus0 at mainbus0 # sun4c 204obio0 at mainbus0 # sun4 and sun4m 205sparcvme0 at mainbus0 # sun4 206iommu0 at mainbus0 # sun4m 207sbus0 at iommu0 # sun4m 208sparcvme0 at iommu0 # sun4m 209vme0 at sparcvme0 # mi VME attachment 210 211## SBus expander box 212xbox* at sbus? slot ? offset ? 213sbus* at xbox? 214 215## SBus to PCMCIA bridge 216# Currently enabling nell* with audioamd* causes panic at attach 217#nell* at sbus? slot ? offset ? # PCMCIA bridge 218#pcmcia* at nell? 219 220#### Standard system devices -- all required for a given architecture 221 222## Auxiliary system registers on sun4c and sun4m 223auxreg0 at mainbus0 # sun4c 224auxreg0 at obio0 # sun4m 225 226## Power status and control register on Sun4m systems 227power0 at obio0 228 229## Mostek clock found on 4/300, sun4c, and sun4m systems. 230## The Mostek clock NVRAM is the "eeprom" on sun4/300 systems. 231clock0 at mainbus0 # sun4c 232clock0 at obio0 # sun4m 233clock0 at obio0 addr 0xf2000000 # sun4/300 234 235## Intersil clock found on 4/100 and 4/200 systems. 236oclock0 at obio0 addr 0xf3000000 # sun4/200 237oclock0 at obio0 addr 0x03000000 # sun4/100 238 239## Memory error registers. 240memreg0 at mainbus0 # sun4c 241memreg0 at obio0 # sun4m 242memreg0 at obio0 addr 0xf4000000 # sun4/200 and sun4/300 243memreg0 at obio0 addr 0x04000000 # sun4/100 244 245## ECC memory control 246eccmemctl0 at mainbus0 # sun4m 247 248## Timer chip found on 4/300, sun4c, and sun4m systems. 249timer0 at mainbus0 # sun4c 250timer0 at obio0 # sun4m 251timer0 at obio0 addr 0xef000000 # sun4/300 252 253## EEPROM found on 4/100 and 4/200 systems. Note that the 4/300 254## doesn't use this driver; the `EEPROM' is in the NVRAM on the 255## Mostek clock chip on 4/300 systems. 256eeprom0 at obio0 addr 0xf2000000 # sun4/200 257eeprom0 at obio0 addr 0x02000000 # sun4/100 258 259 260#### Serial port configuration 261 262## Zilog 8530 serial chips. Each has two-channels. 263## zs0 is ttya and ttyb. zs1 is the keyboard and mouse. 264zs0 at mainbus0 # sun4c 265zs0 at obio0 # sun4m 266zs0 at obio0 addr 0xf1000000 level 12 flags 0x103 # sun4/200 and sun4/300 267zs0 at obio0 addr 0x01000000 level 12 flags 0x103 # sun4/100 268zstty0 at zs0 channel 0 # ttya 269zstty1 at zs0 channel 1 # ttyb 270 271zs1 at mainbus0 # sun4c 272zs1 at obio0 # sun4m 273zs1 at obio0 addr 0xf0000000 level 12 flags 0x103 # sun4/200 and sun4/300 274zs1 at obio0 addr 0x00000000 level 12 flags 0x103 # sun4/100 275kbd0 at zs1 channel 0 # keyboard 276ms0 at zs1 channel 1 # mouse 277 278zs2 at obio0 addr 0xe0000000 level 12 flags 0x103 # sun4/300 279zstty2 at zs2 channel 0 # ttyc 280zstty3 at zs2 channel 1 # ttyd 281 282 283## Magma Serial/Parallel driver 284#magma* at sbus? slot ? offset ? 285#mtty* at magma? 286#mbpp* at magma? 287 288## PCMCIA serial interfaces 289#com* at pcmcia? 290#pcmcom* at pcmcia? 291#com* at pcmcom? 292 293#### Disk controllers and disks 294 295# 296 297## The following flags may be set for the NCR53c94 based esp driver: 298## bits 0-7: disable disconnect/reselect for the corresponding target 299## bits 8-15: disable synchronous negotiation for target [bit-8] 300 301## sun4/300, sun4c, sun4m on-board SCSI, and FSBE/S SBus SCSI cards. 302## Both `dma' and `esp' are needed in all cases. 303## Two kinds of additional SBus SCSI interfaces are available. One uses 304## "esp at sbus" like the sun4c on-board; the other uses "esp at dma". 305 306## sun4/300 SCSI - an NCR53c94 or equivalent behind 307## an LSI Logic DMA controller 308 309dma0 at obio0 addr 0xfa001000 level 4 # sun4/300 310esp0 at obio0 addr 0xfa000000 level 4 flags 0x0000 # sun4/300 311 312dma0 at sbus0 slot ? offset ? # sun4c/sun4m 313esp0 at sbus0 slot ? offset ? flags 0x0000 # sun4c 314esp0 at dma0 flags 0x0000 # sun4m 315 316# FSBE/S SCSI 317dma* at sbus? slot ? offset ? # SBus 318esp* at sbus? slot ? offset ? flags 0x0000 # SBus (older proms) 319esp* at dma? flags 0x0000 # SBus 320 321scsibus* at esp? 322 323## Qlogic ISP SBus SCSI Card 324isp* at sbus? slot ? offset ? 325scsibus* at isp? 326 327## NCR5380-based "Sun SCSI 3" VME SCSI controller. 328## This driver has several flags which may be enabled by OR'ing 329## the values and using the "flags" directive. 330## Valid flags are: 331## 332## 0x01 Use DMA (may be polled) 333## 0x02 Use DMA completion interrupts 334## 0x04 Allow disconnect/reselect 335## 336## E.g. the following would enable DMA, interrupts, and reselect: 337## si0 at vme0 addr 0x200000 irq 3 vect 0x40 flags 0x07 338## 339## By default, DMA is enabled in the driver. 340 341si0 at vme0 addr 0x200000 irq 2 vect 0x40 342scsibus* at si? 343 344## NCR5380-based "SCSI Weird" on-board SCSI interface found 345## on sun4/100 systems. The flags are the same as the "si" 346## controller. Note, while DMA is enabled by default, only 347## polled DMA works at this time, and reselects do not work 348## on this particular controller. 349 350sw0 at obio0 addr 0x0a000000 level 3 351scsibus* at sw? 352 353## PCMCIA SCSI controllers 354#aic* at pcmcia? 355#scsibus* at aic? 356 357 358## These entries find devices on all SCSI busses and assign 359## unit numbers dynamically. 360sd* at scsibus? target ? lun ? # SCSI disks 361st* at scsibus? target ? lun ? # SCSI tapes 362cd* at scsibus? target ? lun ? # SCSI CD-ROMs 363#ch* at scsibus? target ? lun ? # SCSI changer devices 364#ss* at scsibus? target ? lun ? # SCSI scanners 365#uk* at scsibus? target ? lun ? # unknown SCSI 366 367 368## Xylogics 753 or 7053 VME SMD disk controllers and disks, found 369## on sun4 systems. 370xdc0 at vme0 addr 0xee80 irq 3 vect 0x44 371xdc1 at vme0 addr 0xee90 irq 3 vect 0x45 372xdc2 at vme0 addr 0xeea0 irq 3 vect 0x46 373xdc3 at vme0 addr 0xeeb0 irq 3 vect 0x47 374xd* at xdc? drive ? 375 376## Xylogics 451 or 451 VME SMD disk controllers and disks, found 377## on sun4 systems. 378xyc0 at vme0 addr 0xee40 irq 3 vect 0x48 379xyc1 at vme0 addr 0xee48 irq 3 vect 0x49 380xy* at xyc? drive ? 381 382 383## Floppy controller and drive found on SPARCstations. 384 385fdc0 at mainbus0 # sun4c controller 386fdc0 at obio0 # sun4m controller 387fd* at fdc0 # the drive itself 388 389## PCMCIA IDE controllers 390#wdc* at pcmcia? 391#wd* at wdc? 392 393## A disk-like interface to files. Can be used to create floppy, CD, 394## miniroot images, etc. 395 396#pseudo-device vnd 4 397 398## Concatenated and striped disks; with this, you can create a software-based 399## disk array similar to a "RAID 0" setup. See ccd(4). 400 401#pseudo-device ccd 4 402 403## RAIDframe disk driver: software RAID driver. See raid(4). 404 405#pseudo-device raid 4 406 407## Memory disk device, used on boot floppies with compressed 408## kernel-plus-root-disk images. 409 410#pseudo-device md 1 411 412 413#### Network interfaces 414 415## LANCE Ethernet - an AMD 7990 LANCE behind specialized DMA glue 416## Three flavors of additional SBus ethernets are available. One attaches 417## directly like the sun4c on-board, one uses the ledma device like the 418## sun4m on-board, and one uses the lebuffer device. 419 420le0 at obio0 addr 0xf9000000 level 6 # sun4/300 421le0 at sbus0 slot ? offset ? # sun4c on-board 422ledma0 at sbus0 slot ? offset ? # sun4m on-board 423le0 at ledma0 # sun4m on-board 424le* at sbus? slot ? offset ? # SBus 425ledma* at sbus? slot ? offset ? # SBus 426le* at ledma? # SBus 427lebuffer0 at sbus? slot ? offset ? # SBus 428le0 at lebuffer? # SBus 429lebuffer* at sbus? slot ? offset ? # SBus 430le* at lebuffer? # SBus 431 432 433## sun4/100 and sun4/200 Ethernet - an Intel 82586 on-board 434## or on a Multibus/VME card. 435ie0 at obio0 addr 0xf6000000 level 6 # sun4/200 on-board 436ie0 at obio0 addr 0x06000000 level 6 # sun4/100 on-board 437ie1 at vme0 addr 0xe88000 irq 3 vect 0x75 # VME 438ie2 at vme0 addr 0x31ff02 irq 3 vect 0x76 # VME 439ie3 at vme0 addr 0x35ff02 irq 3 vect 0x77 # VME 440ie4 at vme0 addr 0x2dff02 irq 3 vect 0x7c # VME 441 442## qec/be, qec/hme 443qec* at sbus? slot ? offset ? 444be* at qec? 445qe* at qec? 446 447# midway ATM 448en0 at sbus? slot ? offset ? 449 450# PCMCIA ethernet devices 451#ep* at pcmcia? 452#mbe* at pcmcia? 453#ne* at pcmcia? 454#sm* at pcmcia? 455 456# MII/PHY support 457#exphy* at mii? phy ? # 3Com internal PHYs 458#icsphy* at mii? phy ? # Integrated Circuit Systems ICS189x 459#inphy* at mii? phy ? # Intel 82555 PHYs 460#lxtphy* at mii? phy ? # Level One LXT-970 PHYs 461#nsphy* at mii? phy ? # NS83840 PHYs 462#qsphy* at mii? phy ? # Quality Semiconductor QS6612 PHYs 463#sqphy* at mii? phy ? # Seeq 80220/80221/80223 PHYs 464#tlphy* at mii? phy ? # ThunderLAN PHYs 465#ukphy* at mii? phy ? # generic unknown PHYs 466 467## Loopback network interface; required 468pseudo-device loop 469 470## SLIP and CSLIP interfaces, for IP over a serial line. 471#pseudo-device sl 2 472 473## PPP, the successor to SLIP. See pppd(8). 474#pseudo-device ppp 2 475 476## Starmode Radio IP, a special hardware network device. 477#pseudo-device strip 1 478 479## Network "tunnel" device, allowing protocol stacks to run in the userland. 480## This is used by the third-party user-mode "ppp" program, and others. 481#pseudo-device tun 4 482 483## Generic L3 over IP tunnel 484#pseudo-device gre 2 # generic L3 over IP tunnel 485 486## Berkeley Packet Filter, required to run RARPD. A generic C-language 487## interface that allows selective examining of incoming packets. 488#pseudo-device bpfilter 8 489 490## IP Filter, used in firewall and NAT applications. See ipnat(8) for 491## one example of the use of the IP Filter. 492#pseudo-device ipfilter 493 494 495#### Audio and video devices 496 497## /dev/audio support (`audioamd' plus `audio') 498## 499#audioamd0 at mainbus0 # sun4c 500#audioamd0 at obio0 # sun4m 501#audioamd0 at sbus0 slot ? offset ? # sun4m 502#audio* at audioamd0 503 504#audiocs0 at sbus0 slot ? offset ? # SUNW,CS4231 505#audio* at audiocs0 506 507 508## Sun "bwtwo" black and white framebuffer, found on sun4, sun4c, and sun4m 509## systems. If your sun4 system has a cgfour installed in the P4 slot, 510## the P4 entries for "bwtwo" will attach to the overlay plane of the 511## "cgfour". 512 513bwtwo0 at sbus0 slot ? offset ? # sun4c and sun4m 514bwtwo* at sbus? slot ? offset ? # 515#bwtwo0 at obio0 addr 0xfd000000 level 4 # sun4/200 516#bwtwo0 at obio0 addr 0xfb300000 level 4 # sun4/300 in P4 slot 517#bwtwo0 at obio0 addr 0x0b300000 level 4 # sun4/100 in P4 slot 518 519## Sun "cgtwo" VME color framebuffer 520#cgtwo0 at vme0 addr 0x400000 irq ? vect 0xa8 521 522## Sun "cgthree" Sbus color framebuffer 523cgthree0 at sbus? slot ? offset ? 524cgthree* at sbus? slot ? offset ? 525#cgthree0 at obio? slot ? offset ? # sun4m 526 527## Sun "cgfour" color framebuffer with overlay plane. See above comment 528## regarding overlay plane. 529#cgfour0 at obio0 addr 0xfb300000 level 4 # sun4/300 P4 530#cgfour0 at obio0 addr 0x0b300000 level 4 # sun4/100 P4 531 532## Sun "cgsix" accelerated color framebuffer. 533cgsix0 at sbus? slot ? offset ? 534cgsix* at sbus? slot ? offset ? 535#cgsix0 at obio0 addr 0xfb000000 level 4 # sun4/300 P4 536#cgsix0 at obio0 addr 0x0b000000 level 4 # sun4/100 P4 537 538## Sun "cgeight" 24-bit framebuffer 539#cgeight0 at obio0 addr 0xfb300000 level 4 # sun4/300 P4 540#cgeight0 at obio0 addr 0x0b300000 level 4 # sun4/100 P4 541 542## Sun "tcx" accelerated color framebuffer. 543tcx0 at sbus? slot ? offset ? 544tcx* at sbus? slot ? offset ? 545 546# Sun "cgfourteen" accelerated 24-bit framebuffer. 547cgfourteen0 at obio0 # sun4m 548 549 550#### Other device configuration 551 552## Pseudo ttys, required for network logins and programs like screen. 553 554pseudo-device pty 2 # pseudo-terminals (Sysinst needs two) 555 556## Random device, used to implement /dev/random (a source of random noise), 557## and generate randomness for some kernel formulae. 558 559pseudo-device rnd 560