INSTALL revision 1.65
1 # $NetBSD: INSTALL,v 1.65 2009/02/06 18:50:28 jym Exp $ 2 # 3 # from: NetBSD: GENERIC,v 1.84 1999/06/06 13:00:03 mrg Exp 4 # 5 # floppy install kernel. try to keep this in sync with GENERIC but 6 # leave as much disabled as possible. 7 8 include "arch/sparc/conf/std.sparc" 9 10 #options INCLUDE_CONFIG_FILE # embed config file in kernel binary 11 12 makeoptions COPTS="-Os" # Optimise for space. Implies -O2 13 14 maxusers 32 15 16 # Enable the hooks used for initializing the root memory-disk. 17 options MEMORY_DISK_HOOKS 18 options MEMORY_DISK_IS_ROOT # force root on memory disk 19 options MEMORY_DISK_SERVER=0 # no userspace memory disk support 20 ## The miniroot size must be kept in sync manually with the size of 21 ## the `ramdisk' image (which is built in distrib/sparc/ramdisk). 22 options MEMORY_DISK_ROOT_SIZE=1536 # size of memory disk, in blocks 23 options MEMORY_DISK_RBFLAGS=RB_SINGLE # boot in single-user mode 24 25 pseudo-device md 1 # memory disk device (ramdisk) 26 27 ## System kernel configuration. See options(4) for more detail. 28 29 30 # Options for variants of the Sun SPARC architecure. 31 # We currently support three architecture types; at least one is required. 32 options SUN4 # sun4/100, sun4/200, sun4/300 33 options SUN4C # sun4c - SS1, 1+, 2, ELC, SLC, IPC, IPX, etc. 34 options SUN4M # sun4m - SS10, SS20, Classic, etc. 35 36 options SUN4_MMU3L # 3-level MMU on sun4/400 37 38 ## System options specific to the sparc machine type 39 40 # Blink the power LED on some machines to indicate the system load. 41 #options BLINK 42 43 ## Use a faster console than the PROM's slow drawing routines. Not needed 44 ## for headless (no framebuffer) machines. 45 #options RASTERCONSOLE # fast rasterop console 46 #options FONT_GALLANT12x22 # the console font 47 #options FONT_BOLD8x16 # a somewhat smaller font 48 #options RASTERCONSOLE_FGCOL=WSCOL_BLACK 49 #options RASTERCONSOLE_BGCOL=WSCOL_WHITE 50 51 # wscons stuff 52 options WSEMUL_SUN 53 #options WSEMUL_VT100 54 options WSDISPLAY_COMPAT_RAWKBD 55 options WSDISPLAY_CUSTOM_OUTPUT 56 options WS_DEFAULT_FG=WSCOL_BLACK 57 options WS_DEFAULT_BG=WSCOL_LIGHT_WHITE 58 options WS_KERNEL_FG=WSCOL_GREEN 59 options WS_KERNEL_BG=WSCOL_LIGHT_WHITE 60 61 #### System options that are the same for all ports 62 63 ## Root device configuration: change the ?'s if you are going to use a 64 ## nonstandard root partition (other than where the kernel is booted from) 65 ## and/or nonstandard root type (not ffs or nfs). Normally this can be 66 ## automagically determined at boot time. 67 68 config netbsd root on ? type ? 69 70 ## System call tracing (see ktrace(1)). 71 #options KTRACE 72 73 ## Collect statistics on kernel malloc's and free's. This does have a 74 ## significant performance hit on slower machines, so it is intended for 75 ## diagnostic use only. 76 #options KMEMSTATS 77 78 ## System V compatible IPC subsystem. (msgctl(2), semctl(2), and shmctl(2)) 79 #options SYSVMSG # System V message queues 80 #options SYSVSEM # System V semaphores 81 #options SYSVSHM # System V shared memory 82 #options SHMMAXPGS=1024 # 1024 pages is the default 83 84 ## Loadable kernel module support; still under development. 85 86 options USERCONF # userconf(4) support 87 options PIPE_SOCKETPAIR # smaller, but slower pipe(2) 88 #options SYSCTL_INCLUDE_DESCR # Include sysctl descriptions in kernel 89 90 ## NFS boot options; tries DHCP/BOOTP then BOOTPARAM 91 options NFS_BOOT_BOOTPARAM 92 #options NFS_BOOT_BOOTP 93 options NFS_BOOT_DHCP 94 95 #### Debugging options 96 97 ## The DDB in-kernel debugger runs at panic (unless DDB_ONPANIC=0), or at 98 ## serial console break or keyboard reset, where the PROM would normally 99 ## intercept. DDB_HISTORY_SIZE adds up/down arrow command history. 100 #options DDB # kernel dynamic debugger 101 #options DDB_HISTORY_SIZE=100 # enable history editing in DDB 102 #options DDB_ONPANIC=1 # see also sysctl(8): `ddb.onpanic' 103 104 ## You may also use gdb, on another computer connected to this machine over 105 ## a serial port. Both KGDB_DEV and KGDB_DEVRATE should be specified; 106 ## KGDB_DEV is a dev_t encoded device number of the serial port to use. 107 ## (0xc01 = ttya, 0xc02 = ttyb.) 108 #options KGDB # support for kernel gdb 109 #options KGDB_DEV=0xc01 # kgdb device number (this is `ttyb') 110 #options KGDB_DEVRATE=38400 # baud rate 111 112 113 ## Compile the kernel with debugging symbols (`netbsd.gdb' is the debug file), 114 ## such that gdb(1) can be used on a kernel coredump. 115 116 #makeoptions DEBUG="-g" 117 118 119 ## Adds code to the kernel that does internal consistency checks, and will 120 ## cause the kernel to panic if corruption of internal data structures 121 ## is detected. 122 #options DIAGNOSTIC # extra kernel sanity checking 123 124 ## Enable (possibly expensive) debugging code that may also display messages 125 ## on the system console 126 #options DEBUG 127 128 #options MIIVERBOSE # verbose PHY autoconfig messages 129 130 ## Make SCSI error messages more verbose when explaining their meanings. 131 #options SCSIVERBOSE 132 133 ## `INSECURE' turns off the kernel security level (securelevel = 0 always). 134 ## This allows writing to /dev/mem, loading kernel modules while multi-user, 135 ## and other insecurities good only for development work. Do not use this 136 ## option on a production machine. 137 options INSECURE 138 139 ## `FDSCRIPTS' allows non-readable but executable scripts by providing a 140 ## pre-opened opaque file to the script interpreter. `SETUIDSCRIPTS', 141 ## which implies FDSCRIPTS, allows scripts to be set-user-id using the same 142 ## opaque file mechanism. Perl calls this "secure setuid scripts." 143 144 #options FDSCRIPTS 145 #options SETUIDSCRIPTS 146 147 ## Options for compatibility with previous releases foreign system binaries. 148 ## In the cases of COMPAT_SUNOS and COMPAT_SVR4, you may need to set up 149 ## additional user-level utilities or system configuration files. See 150 ## compat_sunos(8) and compat_svr4(8). 151 152 #options COMPAT_43 # 4.3BSD system interfaces 153 #options COMPAT_10 # NetBSD 1.0 binary compatibility 154 #options COMPAT_11 # NetBSD 1.1 binary compatibility 155 #options COMPAT_12 # NetBSD 1.2 binary compatibility 156 #options COMPAT_13 # NetBSD 1.3 binary compatibility 157 #options COMPAT_14 # NetBSD 1.4 binary compatibility 158 #options COMPAT_15 # NetBSD 1.5 binary compatibility 159 #options COMPAT_16 # NetBSD 1.6 binary compatibility 160 #options COMPAT_20 # NetBSD 2.0 binary compatibility 161 #options COMPAT_30 # NetBSD 3.0 binary compatibility 162 #options COMPAT_40 # NetBSD 4.0 binary compatibility 163 #options COMPAT_SUNOS # SunOS 4.x binary compatibility 164 #options COMPAT_SVR4 # SunOS 5.x binary compatibility 165 #options TCP_COMPAT_42 # 4.2BSD TCP/IP bug compat. Not recommended. 166 options COMPAT_BSDPTY # /dev/[pt]ty?? ptys. 167 168 ## File systems. You probably need at least one of FFS or NFS. 169 file-system FFS # Berkeley Fast Filesystem 170 file-system NFS # Sun NFS-compatible filesystem client 171 #file-system KERNFS # kernel data-structure filesystem 172 #file-system NULLFS # NULL layered filesystem 173 file-system MFS # memory-based filesystem 174 #file-system FDESC # user file descriptor filesystem 175 #file-system UMAPFS # uid/gid remapping filesystem 176 #file-system LFS # Log-based filesystem (still experimental) 177 #file-system PORTAL # portal filesystem (still experimental) 178 #file-system PROCFS # /proc 179 file-system CD9660 # ISO 9660 + Rock Ridge file system 180 #file-system UNION # union file system 181 #file-system MSDOSFS # MS-DOS FAT filesystem(s). 182 #file-system PTYFS # /dev/pts/N support 183 184 ## File system options 185 #options NFSSERVER # Sun NFS-compatible filesystem server 186 #options QUOTA # FFS quotas 187 #options FFS_EI # FFS Endian Independent support 188 #options NFS_V2_ONLY # Exclude NFS3 code to save space 189 options FFS_NO_SNAPSHOT # No FFS snapshot support 190 options WAPBL # File system journaling support - Experimental 191 192 ## Network protocol support. In most environments, INET is required. 193 options INET # IP (Internet Protocol) v4 194 #options GATEWAY # packet forwarding ("router switch") 195 #options MROUTING # packet forwarding of multicast packets 196 #options PIM # Protocol Independent Multicast 197 #options DIRECTED_BROADCAST # allow broadcasts through routers 198 #options ISO,TPIP # OSI networking 199 #options EON # OSI tunneling over IP 200 #options NETATALK # AppleTalk (over Ethernet) protocol 201 #options NTP # Network Time Protocol in-kernel support 202 #options PPS_SYNC # Add serial line synchronization for NTP 203 #options PFIL_HOOKS # Add pfil(9) hooks, intended for custom LKMs. 204 #options IPFILTER_LOG # Add ipmon(8) logging for ipfilter device 205 #options IPFILTER_LOOKUP # ippool(8) support 206 #options PPP_BSDCOMP # Add BSD compression to ppp device 207 #options PPP_DEFLATE # Add deflate (libz) compression to ppp device 208 #options PPP_FILTER # Add active filters for ppp (via bpf) 209 #options TCP_DEBUG # Record last TCP_NDEBUG packets with SO_DEBUG 210 211 212 #### Main bus and CPU .. all systems. 213 mainbus0 at root 214 cpu0 at mainbus0 215 216 #### Bus types found on SPARC systems. 217 218 sbus0 at mainbus0 # sun4c 219 obio0 at mainbus0 # sun4 and sun4m 220 sparcvme0 at mainbus0 # sun4 221 iommu0 at mainbus0 # sun4m 222 sbus0 at iommu0 # sun4m 223 sparcvme0 at iommu0 # sun4m 224 vme0 at sparcvme0 # mi VME attachment 225 226 ## SBus expander box 227 xbox* at sbus? slot ? offset ? 228 sbus* at xbox? 229 230 ## SBus to PCMCIA bridge 231 # Currently enabling nell* with audioamd* causes panic at attach 232 #nell* at sbus? slot ? offset ? # PCMCIA bridge 233 #pcmcia* at nell? 234 235 #### Standard system devices -- all required for a given architecture 236 237 ## Auxiliary system registers on sun4c and sun4m 238 auxreg0 at mainbus0 # sun4c 239 auxreg0 at obio0 # sun4m 240 241 ## Power status and control register on Sun4m systems 242 power0 at obio0 243 244 ## Mostek clock found on 4/300, sun4c, and sun4m systems. 245 ## The Mostek clock NVRAM is the "eeprom" on sun4/300 systems. 246 clock0 at mainbus0 # sun4c 247 clock0 at obio0 # sun4m 248 clock0 at obio0 addr 0xf2000000 # sun4/300 249 250 ## Intersil clock found on 4/100 and 4/200 systems. 251 oclock0 at obio0 addr 0xf3000000 # sun4/200 252 oclock0 at obio0 addr 0x03000000 # sun4/100 253 254 ## Memory error registers. 255 memreg0 at mainbus0 # sun4c 256 memreg0 at obio0 # sun4m 257 memreg0 at obio0 addr 0xf4000000 # sun4/200 and sun4/300 258 memreg0 at obio0 addr 0x04000000 # sun4/100 259 260 ## ECC memory control 261 eccmemctl0 at mainbus0 # sun4m 262 263 ## Timer chip found on 4/300, sun4c, and sun4m systems. 264 timer0 at mainbus0 # sun4c 265 timer0 at obio0 # sun4m 266 timer0 at obio0 addr 0xef000000 # sun4/300 267 268 ## EEPROM found on 4/100 and 4/200 systems. Note that the 4/300 269 ## doesn't use this driver; the `EEPROM' is in the NVRAM on the 270 ## Mostek clock chip on 4/300 systems. 271 eeprom0 at obio0 addr 0xf2000000 # sun4/200 272 eeprom0 at obio0 addr 0x02000000 # sun4/100 273 274 275 #### Serial port configuration 276 277 ## Zilog 8530 serial chips. Each has two-channels. 278 ## zs0 is ttya and ttyb. zs1 is the keyboard and mouse. 279 zs0 at mainbus0 # sun4c 280 zs0 at obio0 # sun4m 281 zs0 at obio0 addr 0xf1000000 level 12 flags 0x103 # sun4/200 and sun4/300 282 zs0 at obio0 addr 0x01000000 level 12 flags 0x103 # sun4/100 283 284 zs1 at mainbus0 # sun4c 285 zs1 at obio0 # sun4m 286 zs1 at obio0 addr 0xf0000000 level 12 flags 0x103 # sun4/200 and sun4/300 287 zs1 at obio0 addr 0x00000000 level 12 flags 0x103 # sun4/100 288 289 zs2 at obio0 addr 0xe0000000 level 12 # sun4/300 290 291 zstty* at zs? 292 293 # these are for wscons 294 kbd0 at zstty? 295 ms0 at zstty? 296 wskbd* at wskbddev? 297 wsmouse* at wsmousedev? 298 299 ## Magma Serial/Parallel driver 300 #magma* at sbus? slot ? offset ? 301 #mtty* at magma? 302 #mbpp* at magma? 303 304 ## PCMCIA serial interfaces 305 #com* at pcmcia? 306 #pcmcom* at pcmcia? 307 #com* at pcmcom? 308 309 #### Disk controllers and disks 310 311 # 312 313 ## The following flags may be set for the NCR53c94 based esp driver: 314 ## bits 0-7: disable disconnect/reselect for the corresponding target 315 ## bits 8-15: disable synchronous negotiation for target [bit-8] 316 317 ## sun4/300, sun4c, sun4m on-board SCSI, and FSBE/S SBus SCSI cards. 318 ## Both `dma' and `esp' are needed in all cases. 319 ## Two kinds of additional SBus SCSI interfaces are available. One uses 320 ## "esp at sbus" like the sun4c on-board; the other uses "esp at dma". 321 322 ## sun4/300 SCSI - an NCR53c94 or equivalent behind 323 ## an LSI Logic DMA controller 324 325 dma0 at obio0 addr 0xfa001000 level 4 # sun4/300 326 esp0 at obio0 addr 0xfa000000 level 4 flags 0x0000 # sun4/300 327 328 dma0 at sbus0 slot ? offset ? # sun4c/sun4m 329 esp0 at sbus0 slot ? offset ? flags 0x0000 # sun4c 330 esp0 at dma0 flags 0x0000 # sun4m 331 332 # FSBE/S SCSI 333 dma* at sbus? slot ? offset ? # SBus 334 esp* at sbus? slot ? offset ? flags 0x0000 # SBus (older proms) 335 esp* at dma? flags 0x0000 # SBus 336 337 scsibus* at esp? 338 339 ## Qlogic ISP SBus SCSI Card 340 isp* at sbus? slot ? offset ? 341 scsibus* at isp? 342 343 ## NCR5380-based "Sun SCSI 3" VME SCSI controller. 344 ## This driver has several flags which may be enabled by OR'ing 345 ## the values and using the "flags" directive. 346 ## Valid flags are: 347 ## 348 ## 0x01 Use DMA (may be polled) 349 ## 0x02 Use DMA completion interrupts 350 ## 0x04 Allow disconnect/reselect 351 ## 352 ## E.g. the following would enable DMA, interrupts, and reselect: 353 ## si0 at vme0 addr 0x200000 irq 3 vect 0x40 flags 0x07 354 ## 355 ## By default, DMA is enabled in the driver. 356 357 si0 at vme0 addr 0x200000 irq 2 vect 0x40 358 scsibus* at si? 359 360 ## NCR5380-based "SCSI Weird" on-board SCSI interface found 361 ## on sun4/100 systems. The flags are the same as the "si" 362 ## controller. Note, while DMA is enabled by default, only 363 ## polled DMA works at this time, and reselects do not work 364 ## on this particular controller. 365 366 sw0 at obio0 addr 0x0a000000 level 3 367 scsibus* at sw? 368 369 ## PCMCIA SCSI controllers 370 #aic* at pcmcia? 371 #scsibus* at aic? 372 373 374 ## These entries find devices on all SCSI busses and assign 375 ## unit numbers dynamically. 376 sd* at scsibus? target ? lun ? # SCSI disks 377 st* at scsibus? target ? lun ? # SCSI tapes 378 cd* at scsibus? target ? lun ? # SCSI CD-ROMs 379 #ch* at scsibus? target ? lun ? # SCSI changer devices 380 #ss* at scsibus? target ? lun ? # SCSI scanners 381 #uk* at scsibus? target ? lun ? # unknown SCSI 382 383 384 ## Xylogics 753 or 7053 VME SMD disk controllers and disks, found 385 ## on sun4 systems. 386 xdc0 at vme0 addr 0xee80 irq 3 vect 0x44 387 xdc1 at vme0 addr 0xee90 irq 3 vect 0x45 388 xdc2 at vme0 addr 0xeea0 irq 3 vect 0x46 389 xdc3 at vme0 addr 0xeeb0 irq 3 vect 0x47 390 xd* at xdc? drive ? 391 392 ## Xylogics 451 or 451 VME SMD disk controllers and disks, found 393 ## on sun4 systems. 394 xyc0 at vme0 addr 0xee40 irq 3 vect 0x48 395 xyc1 at vme0 addr 0xee48 irq 3 vect 0x49 396 xy* at xyc? drive ? 397 398 399 ## Floppy controller and drive found on SPARCstations. 400 401 fdc0 at mainbus0 # sun4c controller 402 fdc0 at obio0 # sun4m controller 403 fd* at fdc0 # the drive itself 404 405 ## PCMCIA IDE controllers 406 #wdc* at pcmcia? 407 #wd* at wdc? 408 409 ## A disk-like interface to files. Can be used to create floppy, CD, 410 ## miniroot images, etc. 411 412 #pseudo-device vnd 413 414 ## Concatenated and striped disks; with this, you can create a software-based 415 ## disk array similar to a "RAID 0" setup. See ccd(4). 416 417 #pseudo-device ccd 4 418 419 ## RAIDframe disk driver: software RAID driver. See raid(4). 420 421 #pseudo-device raid 4 422 423 ## Memory disk device, used on boot floppies with compressed 424 ## kernel-plus-root-disk images. 425 426 #pseudo-device md 1 427 428 429 #### Network interfaces 430 431 ## LANCE Ethernet - an AMD 7990 LANCE behind specialized DMA glue 432 ## Three flavors of additional SBus ethernets are available. One attaches 433 ## directly like the sun4c on-board, one uses the ledma device like the 434 ## sun4m on-board, and one uses the lebuffer device. 435 436 le0 at obio0 addr 0xf9000000 level 6 # sun4/300 437 le0 at sbus0 slot ? offset ? # sun4c on-board 438 ledma0 at sbus0 slot ? offset ? # sun4m on-board 439 le0 at ledma0 # sun4m on-board 440 le* at sbus? slot ? offset ? # SBus 441 ledma* at sbus? slot ? offset ? # SBus 442 le* at ledma? # SBus 443 lebuffer0 at sbus? slot ? offset ? # SBus 444 le0 at lebuffer? # SBus 445 lebuffer* at sbus? slot ? offset ? # SBus 446 le* at lebuffer? # SBus 447 448 449 ## sun4/100 and sun4/200 Ethernet - an Intel 82586 on-board 450 ## or on a Multibus/VME card. 451 ie0 at obio0 addr 0xf6000000 level 6 # sun4/200 on-board 452 ie0 at obio0 addr 0x06000000 level 6 # sun4/100 on-board 453 ie1 at vme0 addr 0xe88000 irq 3 vect 0x75 # VME 454 ie2 at vme0 addr 0x31ff02 irq 3 vect 0x76 # VME 455 ie3 at vme0 addr 0x35ff02 irq 3 vect 0x77 # VME 456 ie4 at vme0 addr 0x2dff02 irq 3 vect 0x7c # VME 457 458 ## qec/be, qec/hme 459 qec* at sbus? slot ? offset ? 460 be* at qec? 461 qe* at qec? 462 463 # midway ATM 464 en0 at sbus? slot ? offset ? 465 466 # PCMCIA ethernet devices 467 #ep* at pcmcia? 468 #mbe* at pcmcia? 469 #ne* at pcmcia? 470 #sm* at pcmcia? 471 472 # MII/PHY support 473 #exphy* at mii? phy ? # 3Com internal PHYs 474 #icsphy* at mii? phy ? # Integrated Circuit Systems ICS189x 475 #inphy* at mii? phy ? # Intel 82555 PHYs 476 #lxtphy* at mii? phy ? # Level One LXT-970 PHYs 477 #nsphy* at mii? phy ? # NS83840 PHYs 478 #qsphy* at mii? phy ? # Quality Semiconductor QS6612 PHYs 479 #sqphy* at mii? phy ? # Seeq 80220/80221/80223 PHYs 480 #tlphy* at mii? phy ? # ThunderLAN PHYs 481 #ukphy* at mii? phy ? # generic unknown PHYs 482 483 ## Loopback network interface; required 484 pseudo-device loop 485 486 ## SLIP and CSLIP interfaces, for IP over a serial line. 487 #pseudo-device sl 488 489 ## PPP, the successor to SLIP. See pppd(8). 490 #pseudo-device ppp 491 492 ## Starmode Radio IP, a special hardware network device. 493 #pseudo-device strip 494 495 ## Network "tunnel" device, allowing protocol stacks to run in the userland. 496 ## This is used by the third-party user-mode "ppp" program, and others. 497 #pseudo-device tun 498 499 ## Generic L3 over IP tunnel 500 #pseudo-device gre # generic L3 over IP tunnel 501 502 ## Berkeley Packet Filter, required to run RARPD. A generic C-language 503 ## interface that allows selective examining of incoming packets. 504 #pseudo-device bpfilter 505 506 ## IP Filter, used in firewall and NAT applications. See ipnat(8) for 507 ## one example of the use of the IP Filter. 508 #pseudo-device ipfilter 509 510 511 #### Audio and video devices 512 513 ## /dev/audio support (`audioamd' plus `audio') 514 ## 515 #audioamd0 at mainbus0 # sun4c 516 #audioamd0 at obio0 # sun4m 517 #audioamd0 at sbus0 slot ? offset ? # sun4m 518 #audio* at audioamd0 519 520 #audiocs0 at sbus0 slot ? offset ? # SUNW,CS4231 521 #audio* at audiocs0 522 523 524 ## Sun "bwtwo" black and white framebuffer, found on sun4, sun4c, and sun4m 525 ## systems. If your sun4 system has a cgfour installed in the P4 slot, 526 ## the P4 entries for "bwtwo" will attach to the overlay plane of the 527 ## "cgfour". 528 529 bwtwo0 at sbus0 slot ? offset ? # sun4c and sun4m 530 bwtwo* at sbus? slot ? offset ? # 531 #bwtwo0 at obio0 addr 0xfd000000 level 4 # sun4/200 532 #bwtwo0 at obio0 addr 0xfb300000 level 4 # sun4/300 in P4 slot 533 #bwtwo0 at obio0 addr 0x0b300000 level 4 # sun4/100 in P4 slot 534 535 ## Sun "cgtwo" VME color framebuffer 536 #cgtwo0 at vme0 addr 0x400000 irq ? vect 0xa8 537 538 ## Sun "cgthree" Sbus color framebuffer 539 cgthree0 at sbus? slot ? offset ? 540 cgthree* at sbus? slot ? offset ? 541 #cgthree0 at obio? slot ? offset ? # sun4m 542 543 ## Sun "cgfour" color framebuffer with overlay plane. See above comment 544 ## regarding overlay plane. 545 #cgfour0 at obio0 addr 0xfb300000 level 4 # sun4/300 P4 546 #cgfour0 at obio0 addr 0x0b300000 level 4 # sun4/100 P4 547 548 ## Sun "cgsix" accelerated color framebuffer. 549 cgsix0 at sbus? slot ? offset ? 550 cgsix* at sbus? slot ? offset ? 551 #cgsix0 at obio0 addr 0xfb000000 level 4 # sun4/300 P4 552 #cgsix0 at obio0 addr 0x0b000000 level 4 # sun4/100 P4 553 554 ## Sun "cgeight" 24-bit framebuffer 555 #cgeight0 at obio0 addr 0xfb300000 level 4 # sun4/300 P4 556 #cgeight0 at obio0 addr 0x0b300000 level 4 # sun4/100 P4 557 558 ## Sun "tcx" accelerated color framebuffer. 559 #tcx0 at sbus? slot ? offset ? 560 #tcx* at sbus? slot ? offset ? 561 562 # Sun "cgfourteen" accelerated 24-bit framebuffer. 563 cgfourteen* at obio0 # sun4m 564 565 # P9100-based display on Tadpole SPARCbook 3. 566 pnozz0 at sbus? slot ? offset ? 567 568 # Sun ZX/Leo 24-bit framebuffer 569 # XXX no wsdisplay support 570 #zx* at sbus? slot ? offset ? 571 572 # Fujitsu AG-10e accelerated graphics 8/24-bit board 573 agten* at sbus? slot ? offset ? 574 575 # generic framebuffer console 576 genfb* at sbus? slot ? offset ? 577 578 # make sure wsdisplay0 is the console 579 wsdisplay0 at wsemuldisplaydev? console 1 580 wsdisplay* at wsemuldisplaydev? 581 582 #### Other device configuration 583 584 ## Pseudo ttys, required for network logins and programs like screen. 585 586 pseudo-device pty 2 # pseudo-terminals (Sysinst needs two) 587 588 ## Random device, used to implement /dev/random (a source of random noise), 589 ## and generate randomness for some kernel formulae. 590 591 pseudo-device rnd 592 #pseudo-device fss 4 # file system snapshot device 593 594 pseudo-device wsmux # mouse and keyboard multiplexor 595 pseudo-device wsfont 596
Indexes created Fri Oct 03 02:09:57 GMT 2025