Home | History | Annotate | Line # | Download | only in mca 
      1 /*	$NetBSD: 3c523reg.h,v 1.2 2008/04/28 20:23:53 martin Exp $	*/
      2 
      3 /*-
      4  * Copyright (c) 2001 The NetBSD Foundation, Inc.
      5  * All rights reserved.
      6  *
      7  * Redistribution and use in source and binary forms, with or without
      8  * modification, are permitted provided that the following conditions
      9  * are met:
     10  * 1. Redistributions of source code must retain the above copyright
     11  *    notice, this list of conditions and the following disclaimer.
     12  * 2. Redistributions in binary form must reproduce the above copyright
     13  *    notice, this list of conditions and the following disclaimer in the
     14  *    documentation and/or other materials provided with the distribution.
     15  *
     16  * THIS SOFTWARE IS PROVIDED BY THE NETBSD FOUNDATION, INC. AND CONTRIBUTORS
     17  * ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED
     18  * TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
     19  * PURPOSE ARE DISCLAIMED.  IN NO EVENT SHALL THE FOUNDATION OR CONTRIBUTORS
     20  * BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
     21  * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
     22  * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
     23  * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
     24  * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
     25  * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
     26  * POSSIBILITY OF SUCH DAMAGE.
     27  */
     28 
     29 /*
     30  * The 3c523 i/o space is 8 bytes long. The first 6 bytes is the ethernet
     31  * address, followed by control & status register and card's revision number.
     32  */
     33 #define	ELMC_IOADDR_BASE	0x300
     34 #define	ELMC_IOADDR_SIZE	8
     35 #define ELMC_CTRL		6	/* control & status register */
     36 #define ELMC_REVISION		7	/* revision, first 4 bits only */
     37 #define ELMC_REVISION_MASK	0xf
     38 
     39 /*
     40  * The following define the bits for the control & status register.
     41  *
     42  * The bank select registers can be used if there is more than 16KB
     43  * of memory on the card. Bank 3 is the one for the bottom 16KB
     44  * (i.e. the common size), but the card defaults to bank 0. Hence we
     45  * need to set the bank to 3 to make the card operate at all.
     46  */
     47 #define ELMC_CTRL_BS0		0x01	/* RW bank select */
     48 #define ELMC_CTRL_BS1		0x02	/* RW bank select */
     49 #define ELMC_CTRL_BS3		(ELMC_CTRL_BS0|ELMC_CTRL_BS1)	/* shortcut */
     50 #define ELMC_CTRL_INT		0x04	/* RW interrupt enable, assert high */
     51 #define ELMC_CTRL_LOOP		0x20	/* RW loopback enable, assert high */
     52 #define ELMC_CTRL_CHA		0x40	/* RW channel attention, assert high */
     53 #define ELMC_CTRL_RST		0x80	/* RW 82586 reset, assert low */
     54 
     55 /*
     56  * The base memory space address is 0xc0000 (see 3c523 docs). The card
     57  * has actually 24KB of memory, but we only use first 16KB -
     58  * the upper 8KB is card's BIOS.
     59  */
     60 #define ELMC_MADDR_BASE		0x0c0000
     61 #define ELMC_MADDR_SIZE		0x4000		/* use only 16K of shared mem */
     62 
     63