| /src/sys/arch/arm/nxp/ |
| imx_com.c | 73 struct clk *per; local in function:imx_com_attach
92 per = fdtbus_clock_get(phandle, "per");
93 if (per != NULL && clk_enable(per) != 0) {
94 aprint_error(": couldn't enable per clock\n");
103 if (per != NULL) {
104 aprint_normal(", %u Hz", clk_get_rate(per));
106 imxuart_set_frequency(clk_get_rate(per), 2);
|
| /src/sys/dev/ |
| lockstat.c | 163 * Prepare the per-CPU tables for use, or clear down tables when tracing is
169 int i, per, slop, cpuno; local in function:lockstat_init_tables
189 per = le->le_nbufs / ncpu;
190 slop = le->le_nbufs - (per * ncpu);
201 for (i = per; i != 0; i--, lb++) {
|
| /src/sys/arch/amiga/dev/ |
| aucc.c | 101 aucc_data_t sc_channel[4]; /* per channel freq, ... */
265 /* init values per channel */
337 u_long per; local in function:aucc_set_out_sr
341 per = freqtoper(sr);
342 if (per > 0xffff)
344 sr = pertofreq(per);
348 sc->sc_channel[i].nd_per = per;
425 custom.aud[i].per = sc->sc_channel[i].nd_per;
508 * compute output length in bytes per channel.
528 custom.aud[i].per = sc->sc_channel[i].nd_per
808 u_int per; local in function:freqtoper
[all...] |
| /src/sys/arch/amiga/amiga/ |
| custom.h | 140 unsigned short per; member in struct:Custom::Audio
|
| /src/sys/dev/ic/ |
| mfi.c | 2040 int i, per, rv = EINVAL; local in function:mfi_ioctl_vol
2093 per = (int)sc->sc_ld_details.mld_progress.mlp_cc.mp_progress;
2094 bv->bv_percent = (per * 100) / 0xffff;
2101 per = (int)sc->sc_ld_details.mld_progress.mlp_bgi.mp_progress;
2102 bv->bv_percent = (per * 100) / 0xffff;
2114 * The RAID levels are determined per the SNIA DDF spec, this is only
2125 bv->bv_size = sc->sc_ld_details.mld_size * 512; /* bytes per block */
2236 bd->bd_size = pd->mpd_size * 512; /* bytes per block */
2494 vdhs->bv_size = pd->mpd_size * 512; /* bytes per block */
2502 sdhs->bd_size = pd->mpd_size * 512; /* bytes per block *
[all...] |
| isp.c | 1193 /* First do overall per-card settings. */
1274 /* now do per-channel settings */
1388 * Set current per-target parameters to an initial safe minimum.
1430 isp_prt(isp, ISP_LOGDEBUG0, "Initial Settings bus%d tgt%d flags 0x%x off 0x%x per 0x%x",
6232 * isn't an error, per se.
7329 * There are no 'per-bus' settings for Fibre Channel.
7485 uint8_t off, per; local in function:isp_setdfltsdparm
7499 per = ISP_80M_SYNCPARMS & 0xff;
7502 per = ISP_40M_SYNCPARMS & 0xff;
7505 per = ISP_20M_SYNCPARMS & 0xff
[all...] |
| /src/sys/compat/linux/common/ |
| linux_misc.c | 1153 syscallarg(unsigned long) per;
1156 int per; local in function:linux_sys_personality
1158 per = SCARG(uap, per);
1160 if (per == LINUX_PER_QUERY) {
1165 switch (per & LINUX_PER_MASK) {
1168 led->led_personality = per;
1175 retval[0] = per;
|
| /src/sys/dev/usb/ |
| ohci.c | 646 * The OHCI hardware can handle at most one page crossing per
811 uint32_t s, ctl, rwc, ival, hcr, fm, per, rev, desca /*, descb */; local in function:ohci_init
1044 per = OHCI_PERIODIC(ival); /* 90% periodic */
1045 OWRITE4(sc, OHCI_PERIODIC_START, per);
1752 /* Do not allow RHSC interrupts > 1 per second */
|
| if_athn_usb.h | 217 uint8_t per; member in struct:ar_wmi_evt_txrate
|
| /src/sys/arch/hp300/stand/common/ |
| scsireg.h | 356 u_char per : 1; /* post error */ member in struct:scsi_err_recovery
|
| /src/sys/dev/pci/ |
| mfii.c | 3105 int i, per, rv = EINVAL; local in function:mfii_ioctl_vol
3152 per = (int)sc->sc_ld_details[i].mld_progress.mlp_cc.mp_progress;
3153 bv->bv_percent = (per * 100) / 0xffff;
3160 per = (int)sc->sc_ld_details[i].mld_progress.mlp_bgi.mp_progress;
3161 bv->bv_percent = (per * 100) / 0xffff;
3180 * The RAID levels are determined per the SNIA DDF spec, this is only
3191 bv->bv_size = sc->sc_ld_details[i].mld_size * 512; /* bytes per block */
3327 bd->bd_size = pd->mpd_size * 512; /* bytes per block */
|
